Sears 10853 Instructions Manual

ASSEMBLY INSTRUCTIONS: 10853 Large Rock- Look Fountain with LED lights.

1. Make sure there is access to a GFCI outlet (Ground Fault Circuit Interrupter) designed for outdoor
use that can be used for an electrical supply.

2. Place the base on clean level ground that is free from debris and sharp objects. Make sure not to
place on any surface that may be damaged by water. This fountain is for outdoor use only.

3. Place pump into fountain basin at the back pump cavity.

4. Place both lights in the round indents in the bottom of the basin and tip them to spot light the water
falls area. The lights are soft lighting meant to be seen at night.

5. Hook the wires into the plastic retainers to keep the wires neat.

6. The hose is curled up in the top section, pull out and set top section in place and thread the hose
through the middle hole at the same time.

7. Connect pump outlet to hose. Make sure the hose is not crimped as it will restrict the water flow.

8. Fill basin with water.

9. Plug pump into appropriate outdoor outlet. (If you are unclear about what is an appropriate outlet,
please consult a certified electrician familiar with local codes.)

10. Check water flow and examine fountain for leaks.

11. Put the pump cover in place.

12. Enjoy your fountain – please remember to keep adding water as needed. Hint: If bubbles start to
show in the water outlet, it is usually because the water is too low and the pump intake is starting to
suck in air. Add water until the air bubbles go away.

DO NOT RETURN THIS ARTICLE TO THE STORE

CUSTOMER SERVICE CENTER

Thank you for purchasing your new fountain.

Should you encounter problems after following all the steps herein contained please contact our

customer support: Call 1-866-231-8893 or email: [e-mail]

Kindly provide the model #, place and date of purchase and a short description of the problem

ATTENTION

Troubleshooting:

If no water comes out, disconnect the power supply and verify if any hose is crushed.
Make sure there is enough water in the fountain.
Connect and disconnect the power a few times. The pump should function.
Wait a while in order to allow the water to circulate properly.

Be careful not to spill water onto the plug of the pump.

DO NOT allow the pump to run dry!

Keep the water clean at all times.
Remove all forms of debris.
Never run the pump dry.
Verify water level frequently to compensate for evaporation during the summer.

This fountain must be stored indoors for the winter.

This fountain is for outdoor decorative use only.
This fountain is designed to function with water only.
Never leave a running fountain unattended.
The water in the fountain is not safe to drink
Keep away from small children and pets.

WARNING! RISK OF ELECTRICAL SHOCK!

This pump is supplied with a grounding conductor and grounding type plug. To reduce the risk of electric
shock, be certain that it is connected to a properly grounded, grounding type receptacle.

Always disconnect power supply before manipulating fountain.
Connect only to a grounded outdoor power outlet of 120V- 60Hz.

Do not attempt to repair a damaged pump/power cord. Ask for a replacement pump/cord from the
manufacturer.
To avoid possible injuries do not tamper with pump/cord assembly.

Must be used only with the pump AND /OR transformer AND/OR adapter provided.
Pump Model: PT-707 MIX (0).
AC Adapter Type MAO 121300..

The LED lights will last approximately 2 years and cannot be replaced.
Consult your supplier.

WARNING!

To reduce the risk of electrical shock, use pump only on self-contained fountains no larger than 5 feet in any
dimension.

Precautions:

 Excessive weight or pressure on any of the fountain sections may cause it to tip or fall over. Keep pets and

children away from any of the fountain sections. Do not place any items on the edge of the bowl – such as a
potted plant.
If the entire fountain falls into the water accidentally, turn off the circuit breaker immediately.

 Do not operate the fountain if the pump has been dropped or has a

damaged power cord or plug.

 If the plug or your wall receptacle gets wet due to water dripping down

the power cord or for any other reason, do not remove the plug from
the wall outlet until the circuit breaker is turned off.

 NOTE: Allow the pump power cord to hang at a lower level than the

wall outlet to form a “drip loop”. This will help prevent water from dripping down the power cord and getting

into the wall outlet.

GFCI

DRIP LOOP