Seametrics EX90 Installation Guide

I
EX90 New Meter Installation
Precision Flow Measurement
An ON
CON Brand
Meter with Indicator and hinged cover
Saddle Assembly
(Packaged Separately)
Display Security Seal
Optional
Quick Start Guide
U-clip Retainer
Gasket
Cable Gland
Recommended Tools
Recommended:
3/32” or 2.5mm (small) at head screw driver
Crescent Wrench
• 5/32” Hex Key
Warnings
Conrm that U-clip retainer is installed and never remove the U-clip retainer when pipe is under pressure—may result in serious injury.
Saddle bolts must be tightened evenly. Do not over tighten.
Install security seal during installation if regulations require.
Refer to instruction manual for further details.
Power/Output Cable
Optional:
Channel locks
6” Strap Wrench
Improper sealing of cables or cable glands will void warranty.
Ensure proper grounding when required.
Programming pipe ID, pipe insertion hole size and straight pipe
conguration is required for the meter to read.
253.872.0284 Page 1 of 4 seametrics.com
Positioning
Flow
EX90 New Meter Installation
Quick Start Guide
Choose a position that will ensure a full pipe.
Side (3 o’clock) and top (12 o’clock) installations are acceptable.
Choose a position that will minimize ow distortion.
Flow
*10X/5X
2X
Upstream straight pipe is selected during initial setup. Upstream options are 5X or 10X the diameter and are based on the amount of straight pipe available in either new or propeller meter replacement installation. Downstream straight pipe requirement
is 2X the diameter. See programming setup for details.
BEFORE INSTALLING measure & record inside diameter (ID) of pipe.
1. Clean the mounting surface, remove any roughness from the area.
4. Place saddle top over gasket. Make
sure saddle top covers entire gasket.
Place the saddle clamps under the pipe and align with the clamp guides on the saddle top.
2. Cut a 1.75” hole into pipe. 3. Place gasket centered over pipe
opening.
5. Place saddle plates over saddle
clamp threads. Attach nuts and tighten as shown below. Torque to
6. Insert the EX90 sensor into the saddle tting and secure with U-clip and seal if required.
75 ft-lb in cross pattern.
th
4
nd
2
st
1
rd
3
Seametrics • 19026 72nd Avenue South • Kent, Washington 98032 • USA
(P) 253.872.0284 • (F) 253.872.0285 • 1.800.975.8153 • seametrics.com
LT-14500 r1.6-20190308
3/8/2019
EX90 New Meter Installation
Green (C1) Pulse+
Black (C1) DC-
Quick Start Guide
Wiring
Unscrew the display lid and remove it from the meter. Unsnap the display assembly and remove it from the meter exposing the internal wiring connector. Install the wires through the cable glands into the 2 pin screw connector.
(C1 = power/output cable)
C1
White (C1) Pulse­Green (C1) Pulse+
With Pulse Output Only
With No External Output
If not using external output, no wiring is required.
C1
White (C1) Pulse-
NOTE:
Pulse with External Power
Red (C1) DC+
WARNING: Improper sealing of glands or cables will invalidate any warranty.
Remove plug & o-ring. Insert cable gland/strain relief. Feed cable through cable gland.
Seametrics • 19026 72nd Avenue South • Kent, Washington 98032 • USA
(P) 253.872.0284 • (F) 253.872.0285 • 1.800.975.8153 • seametrics.com
Clamp cable with strain relief clips. Attach drain wire lug to bracket post.
CRITICAL!
Torque cable gland sealing nut to 22 in-lbs.
LT-14500 r1.6-20190308
3/8/2019
Menu System
1.2345678
TAP
TAP
SAMP SETEX EXIT
INFO
PRESS + TO SET OUTER WALL DIAMETER AND WALL THICKNESS
SETUP
SAMP
SAMP SETEX EXIT
INFO
PRESS + TO SET OUTER WALL DIAMETER AND WALL THICKNESS
SETUP
SAMP SETUP EXIT
ID
INFO
PRESS AND TO CHANGE
SAMP SETUP EXIT
HOLE
INFO
PRESS AND TO CHANGE
SAMP SETUP EXIT
PRESS + TO EXIT MENU AND RETURN TO FLOW DISPLAY
INFO
SAMP
SAMP
SAMP
SAMP
LARGE
04.500
IN.
SAMP SETEX EXIT
INFO
PRESS + TO SET OUTER WALL DIAMETER AND WALL THICKNESS
SETUP
SAMP SETUP EXIT
ID
INFO
PRESS AND TO CHANGE
SAMP
SAMP
04.500
IN.
EX90 New Meter Installation
Quick Start Guide
100
All menu screens consist of two rows of tabs surrounding a dialog box that lets you view and change setup parameters. To enter the Menu System perform the hold and tap sequence.
Changing Settings
Enter Pipe Settings (Required)
1. SETUP
View or change meter conguration settings.
2. SETUP (Menu Functionality)
The highlighted value can be changed using the arrows. The value on the left is the menu name. Cycle through these by pressing . Press to highlight and change the value of the menus.
3. ID (Required)
View or change inner diameter of the pipe. Measurement in inches.
4.HOLE (Required)
View or change installation pipe hole size. Tap then to toggle between small and large sizes.
Note: See instruction manual page 14 for hole size description.
5. Pipe (Required)
View or change pipe conguration based on installation. Tap then to toggle between 10/2, 5/2 or STRAIGHT (conditions with 10 diameters or more)
INFO: Meter model, serial number, rmware version SAMP: Sample rate (Default is set to 5 seconds. Battery life with a 5-second
FWD TOTAL
TOTAL CU FT X1000 RATE GPM
The HOME Screen displays ow volume, direction of the ow total and ow RATE along with status conditions such as Empty Pipe. Two buttons below the LCD display are used to access menu screens for viewing and changing meter setup parameters.
These two buttons are light sensors which can detect when a nger is covering them and activate upon release. Only three button touch actions are needed to control navigation through the menus, settings changes and back to the home screen.
HORIZONTAL SCROLLING:
Tap right-hand button to scroll horizontally through
SELECT: Tap left-hand button to change a highlighted item
within a tab dialog. menu tabs or move horizontally within a tab dialog when applicable.
INITIAL SETUP OF ID, HOLE, AND PIPE IS REQUIRED FOR THE METER TO OPERATE PROPERLY.
INFO
PRESS + TO SET OUTER WALL DIAMETER AND WALL THICKNESS
SAMP
SAMP SETEX EXIT
INFO
ID
PRESS AND TO CHANGE
SAMP
SAMP SETUP EXIT
INFO
HOLE
PRESS AND TO CHANGE
SAMP
SAMP SETUP EXIT
INFO
PIPE
PRESS AND TO CHANGE
SAMP SETUP EXIT
SAMP
SETUP
04.500
LARGE
SMALL
10/2 ELB
IN.
sampling rate is four years. Increase sampling interval to extend battery life. (May vary depending on environmental factors. See instruction manual for more details.)
Seametrics • 19026 72nd Avenue South • Kent, Washington 98032 • USA
(P) 253.872.0284 • (F) 253.872.0285 • 1.800.975.8153 • seametrics.com
ENTER/EXIT: Hold left button while tapping right
+
HOLD TAP
button once to enter or exit a tab dialog or to navigate between the HOME and other menu screens.
+
HOLD TAP
EXIT (To SUBMENU)
The EXIT tab in the MAIN MENU has a second function. Tap ve times, to enter a SUBMENU screen from which you can access the following additional options:
T UNIT
View or change TOTAL volume units
R UNIT
View or change ow RATE units
Set P
View or change pulse output scaling
DAMP
View or change # of sample periods for rolling average*
EXIT
Return to HOME SCREEN or enter SUBMENU
T UNIT R UNIT SET P DAMP
PRESS + EXIT MENU AND RETURN TO FLOW DISPLAY
SET 4
SET 20 SET F EXIT
SAMP
T UNIT R UNIT SET P DAMP
TOTAL = GALLONS PRESS + TO SET TOTAL UNITS FOR DISPLAY
SET 20
SET FSAMP EXIT
T UNIT R UNIT SET P DAMP
FLOW RATE = GALLONS/MIN PRESS + TO SET RATE UNITS FOR DISPLAY
SET 20
SET FSAMP EXIT
T UNIT R UNIT SET P DAMP
00001.0 GALLONS PRESS + TO SET GALLONS TOTALIZED PER PULSE SENT OUT PULSE1
SET 20
SET FSAMP EXIT
T UNIT R UNIT SET P DAMP
DAMPING = 1 PRESS + TO SET DAMPING VALUE
SET 20
SET FSAMP EXIT
T UNIT R UNIT SET P DAMP
PRESS + EXIT MENU AND RETURN TO FLOW DISPLAY
SET 20
SET F EXIT
LT-14500 r1.6-20190308
3/8/2019
Loading...