How it Works
Sealife
Loading...
SL670
User Manual
32 pgs9.36 Mb0
Table of contents
Loading...

Sealife SL6722, SL672, SL670, SL6702, SL671 User Manual

...
Sea Dragon 1500
Photo/Video/Dive Light
Item SL672
Sea Dragon 2000
Photo/Video/Dive Light
Item SL984
Sea Dragon 2100 S/F
Photo/Video/Dive Light
Item SL670
Sea Dragon 2500
Photo/Video/Dive Light
Item SL671
Contents:
VII. Maintaining a waterproof seal
VIII. Care and maintenance (After your dive) ................. 11
www.sealife-cameras.com/manuals
Español - Deutsch - Français - Italiano - Nederlands
2
(Before your dive) .......10

I. Safety Warnings

Make sure you follow these important safety warnings to avoid the risk of fire or injury.
Avoid using the light above water for prolonged periods of time. The
light is designed for underwater use and water is needed to displace heat. The metal light head at full power will reach temperature of about 140F (60C) degrees within a few minutes, which may cause burning if touched. A thermal sensor will automatically dim the light if internal temperatures reaches 150F (65C) degrees. Immediately turn off light if any parts of the light become hot to the touch.
If water has entered the light, immediately turn off power and follow these instructions: Remove and dry the battery. DO NOT use the battery
once it has become wet. Wet batteries must be replaced. Allow battery to dry and dispose it in accordance with local battery recycling regulations. The battery chamber is waterproof. If no water has entered the LED light head, the chamber may be cleaned without causing permanent damage to the electronics. Rinse the waterproof battery compartment with fresh water and allow the inside to dry. Replace the o-rings and apply lube. Install new, fully-charged battery and test light. If light does not operate properly, please contact your local SeaLife dealer or the SeaLife service center in your country.
Do not use battery if the outer casing is cracked, separated, damaged or has become wet. Dispose battery in accordance with local battery
recycling regulations.
3

I. Safety Warnings

Never expose battery to fire or intense heat. Do not expose light to direct sunlight for prolonged periods of time.
Remove batteries from light before transporting, traveling or long periods of storage. Remember to use the protective battery cover included when
the battery is not inside the light or charging tray to prevent accidental short-circuiting the battery contacts.
Airlines impose strict safety regulations for handling and shipping lithium ion batteries. Spare lithium batteries may not be packed in your checked baggage but may be packed in your carry-on baggage. It is important to pack spare batteries in such a way as to prevent metal objects from touching the contacts and potentially short-circuiting the battery. Always use protective battery cover included when the battery is not inside the light or charging tray to prevent accidental short-circuiting the battery contacts.
Only use the specified battery and battery charger approved by SeaLife.
Using any other battery or charger may cause fire, injury and permanently damage the light.
Observe all SCUBA dive safety rules and control your buoyancy at all times. Consult your dive instructor for dive safety questions.
Visit www.sealife-cameras.com for updates to this manual and
underwater photography tips.
4

II. Check What You Got

One of the following lights
Sea Dragon 1500F Light (SL672)
with Flex-Connect Grip (SL9905) and
Micro Tray (SL9902)
Sea Dragon 2100SF Light (SL670)
with Flex-Connect Grip (SL9905) and
Single Tray (SL9903)
Sea Dragon 2000F Light (SL984)
with Flex-Connect Grip (SL9905) and
Single Tray (SL9903)
Sea Dragon 2500F Light (SL671)
with Flex-Connect Grip (SL9905) and
Single Tray (SL9903)
5
(GoPro adapter NOT included when light is part
of a SeaLife Camera Set)

III. Product view with call-outs

Major parts 1 - Light head
2 - Metal cooling bezel 3 - Release buttons 4 - Flex-Connect grip 5 - Tray 6 - 1/4-20 Mounting screw 7 - Rubber friction pad 8 - Power button / Brightness adjust 9 - Battery status indicator 10 - Battery cap 11 - Pressure safety valve 12 - Flex-Connect swivel connector
7

IV. Charging and Loading the Battery

1) Charge battery (green light = fully charged)
2) Unscrew the battery cap
3) Insert fully charged battery. Important: Make sure O-ring and sealing surfaces are perfectly
clean and undamaged.
4) Screw on battery cap. (Do not overtighten or use tools.)
Battery charged
when green
8

V. Operating the light

1) Push and hold the power button for 1 second to power ON the light.
2) Push the power button to change between the following light modes:
1500F, 2000F and 2500F lights: 100% 50%
25% 100% etc. 2100SF light: 100% Flood
50% Flood 25% Flood 100% Spot 100% Flood - etc.
3) Push and hold the mode button for 2 seconds to power OFF the light.
Power Button
Battery
status
indicators

VI. Battery Status Indicator

3 status lights indicate remaining battery power:
Status lights Battery power
3 solid 100% 2 solid 75% 1 solid 50% 1 blinking 25%
9

VII. Maintaining a waterproof seal (Before your dive)

1) The light uses two O-rings to maintain a waterproof seal.
2) Every time you open the battery cap make sure the O-rings and sealing surfaces are clean, undamaged and lubricated.
3) Dampen a clean cotton cloth and wipe it around the o-ring and o-ring contact surfaces to remove any hair, sand or debris.
4) Carefully inspect the o-ring for cuts, tears or other damage. Replace o-rings if damaged.
5) Lube O-rings regularly. Apply a small amount of silicone lube on your finger tip and wipe it around the O-rings. Wipe off excess lubricant. The o-ring surface should have shiny, wet appearance.
O-rings
O-rings contact
surface
Important:
Replace O-rings every year if damaged or not. Visit your local SeaLife dealer or www.sealife-cameras.com for information on ordering spare o-rings.
10
Loading...
+ 22 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use