Sealey YK15FFP, YP20FFP, YK30FFP, YK50FFP Instruction Booklet

HYDRAULIC PRESS PREMIER FLOOR TYPE
I
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
WITH FOOT PEDAL
Model no: YK15FFP, YP20FFP, YK30FFP &
YK50FFP
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
Refer to
instructions
Wear a face
shield
Wear protective
gloves
Wear safety
footwear
Wear protective
clothing
Warning;
Crushing of
hands
1. SAFETY
9 Familiarise yourself with the applications, limitations and hazards of the press. 9 Maintain the press in good condition (use an authorised service agent). 9 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 9 Keep the press clean for best and safest performance. 9 locate the press in an adequate working area for its function, keep area clean and tidy and free from unrelated materials and ensure
there is adequate lighting. 9 ensure the workpiece is correctly secured before operating the press. 9 ensure that all fittings are tight before each use. 9 Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair. 9 Keep hands and body clear of the table when operating the press. 9 Maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes. 9 Keep children and unauthorised persons away from the working area. 9 Securely attach the press to a flat, firm, level surface capable of supporting the weight of press and any workpiece taking into account
clearance for workpieces. 9 When not in use, release pressure from the hydraulic unit and clean the press. Stand or store the arbor plates in a safe location.
8 DO NOT operate the press if any parts are missing as this may cause failure and/or possible personal injury. 8 DO NOT use the press for a task it is not designed to perform. 8 DO NOT make any modifications to the press. 8 DO NOT exceed the rated capacity of the press. 8 DO NOT apply off-centre loads. 8 DO NOT allow the workpiece or the arbor plates to fall from the table. 8 DO NOT get the press wet or use in damp or wet locations or areas where there is condensation. 8 DO NOT operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication. 8 DO NOT climb upon the press. 8 DO NOT use the press to compress a spring or any other item that could disengage and cause a potential hazard including personal
injury.
8 DO NOT stand directly in front of a loaded press and never leave a loaded press unattended. 8 DO NOT allow untrained persons to operate the press.
WARNING! Always wear approved eye or face protection when operating the press. A full range of personal safety equipment is
available from your Sealey stockist.
WARNING: DO NOT top up hydraulic unit with brake fluid, or any other fluid other than a good quality hydraulic oil (Sealey Part
number: HJo500MlS/HJo5lS) as this may cause serious damage to the hydraulic unit and will invalidate the warranty.
WARNING! Always position the press against a wall. If the press is situated in an open workshop, it is essential that a guard
be placed at the rear of the unit. This will prevent injury to bystanders in the event of the work piece ejecting suddenly.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.
DANGER! The press is top heavy. If it requires moving after assembly or for relocation, use suitable slings around the top
crossbeam, or lift direct with a forklift with the forks located under the top crossbeam. DO NOT use a pallet truck.
2. INTRODUCTION
Steel frame construction with speed/torque adjustable hydraulic pump featuring manual handle or foot pedal. Sliding hydraulic ram assembly gives from 169 - 245mm of lateral travel (depending on the model). Frame head fitted with ram pressure gauge. Supplied with flat pressing plate/V-blocks.
© Jack Sealey limited
Original Language Version
YK15FFP, YP20FFP, YK30FFP & YK50FFP Issue 2 08/08/18
3. SPECIFICATION
Model: YK15FFP YK20FFP YK30FFP YK50FFP Type: Floor Floor Floor Floor Capacity: 15tonne 20tonne 30tonne 50tonne Ram Stroke: 160mm 185mm 150mm 200mm Lateral Travel: 169mm 179mm 200mm 245mm Maximum Height - Ram to Table: 985mm 918mm 1031mm 1048mm Minimum Height - Ram to Table: 173mm 38mm 151mm 67mm Table Aperture: 140mm 152mm 164mm 235mm Working Table Depth: 156mm 172mm 184mm 259mm Working Table Width: 600mm 630mm 695mm 910mm Overall Height: 1616mm 1619mm 1830mm 1877mm Gauge Included: Yes Yes Yes Yes Weight: 92kg 112kg 186kg 300kg Guard Available (Optional): n/A YKSG20 YKSG30 YKSG50
4. ASSEMbLY
g.1
4.1. PRESS ASSEMbLY (refer to fig.1 as a guide to assembly)
4.1.1. Attach slings around the top cross member, using a suitable hoist or gantry lift the main frame (1) out of the transportation crate into an upright position.
4.1.2. Keep the main frame (1) held safely upright. DO NOT allow to fall. Attach base sections (2) with supports (3) to the left and right hand posts. only fully tighten the securing nuts and bolts when the base sections (2) are square to the main frame.
4.1.3. Attach the hydraulic unit (4) and protection cover (5) to the right hand post of the main frame (1).
4.1.4. Connect the hydraulic hose (6) from the hydraulic unit (4) to the union on the adaptor (7) in the top cross member of the main frame (1).
4.1.5. locate the pressure gauge hole in the adaptor (7) and remove the plug with a hex key (this may be very tightly secured). Screw the pressure gauge (8) into the adaptor (7).
4.1.6. Attach the foot pedal (9) to the hydraulic unit (4) with the connecting bars (10) and secure with the pivot bolt (11) to the bottom of the right hand post of the main frame (1).
4.1.7. (YK50FFP only) Move the hand winch from the inside of the left hand post of the main frame (1) and attach to the outside of the left hand post of the main frame (1). ensure that the cables are located correctly in the rollers before fully tightening (See inset fig.1). Fit the plastic return pipe from the hydraulic unit (fig.2) to the back of the hydraulic ram (fig.3).
4.1.8. Hold work table (12) in position with work table pins (13) and secure with the safety clips (14).
© Jack Sealey limited
Original Language Version
YK15FFP, YP20FFP, YK30FFP & YK50FFP Issue 2 08/08/18
Loading...
+ 2 hidden pages