Page 1
1.1. ELECTRICAL SAFETY
WARNING! It is the owner’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and
all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD together with portable products that are
plugged into an electrical supply not protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual Current
Device by contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by
a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply. The pump and cable are
designed for submerging in water and as such must not be tampered with (if in doubt, contact a qualified electrician).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply leads, plugs and all electrical connections for wear and damage, especially power connections, to
ensure that none is loose.
1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power
supply to be used, and check that plugs are fitted with the correct capacity fuse. A 13 amp
plug may require a fuse smaller than 13 amps for certain products, see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by its power supply lead.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damaged leads, plugs or connections. Immediately replace or have
repaired by a qualified electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted. In case
of damage, cut off and fit a new plug according to the following instructions (discard old plug
safely).
(UK only - see diagram at right). Ensure the unit is correctly earthed via a three-pinplug.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and that
the restraint is tight.
1.1.10. The electrical cable is designed for use in water and must not be substituted. If damaged contact a qualified electrician.
1.1.11. Extension cable use. Only use a cable designed for use with water equipment. Contact your dealer or a qualified electrician
for advice. Ensure water is kept clear of electrical mains power supply. DO NOT touch switch or plug with wet hands.
INSTRUCTIONS FOR:
SUBMERSIBLE POND PUMPS STAINLESS
STEEL
MODEL No's: WPP1750S/WPP3000S/WPP3600S
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.2 . GENERAL SAFETY
WARNING! This pump must be used in accordance with Health & Safety, government, local authority and water authority rules and
regulations including appropriate procedures for the protection of persons, animals, equipment and property.
Familiarise yourself with application, limitations and potential hazards peculiar to the pump.
WARNING! Disconnect the pump from the mains power before changing accessories, servicing or performing any maintenance.
WARNING! DO NOT have contact with the water whilst the submerged pump is connected to the mains supply.
Maintain the pump in good condition (use an authorised service agent). Keep the pump clean.
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Switch off the power on all devices that are in contact with the water before carrying out any cleaning or maintenance work on the device.
DO NOT operate the pump if any parts are damaged or missing as this may cause failure and/or personal injury.
DO NOT use the pump for any purpose other than that for which it is designed.
DO NOT operate the pump out of water. The pump pick-up area must be completely submerged during operation.
DO NOT operate the pump during freezing temperatures. DO NOT leave the pump in water that may freeze.
DO NOT carry the pump by its electrical cable, or outlet pipe.
DO NOT use the device in water additionally chlorinated or in acidic or alkaline solutions.
DO NOT use in salt water.
DO NOT let the pump run dry. This can cause irreparable damage.
RECOMMENDED
FUSE RATING 5 AMP
Original Language Version
WPP1750S, WPP3000S, WPP3600S Issue: 2(L) - 30/06/16
© Jack Sealey Limited
Page 2
2. INTRODUCTION & SPECIFICATIONS
Manufactured from high impact stainless steel for added durability and corrosion resistance. A range of pond pumps suitable for creating
garden water features such as fountains and waterfalls. They also provide the important functions of filtration and water circulation which
are necessary to maintain healthy plant and fish life.
3. OPERATING INSTRUCTIONS
WARNING! Ensure that you read, understand and apply the safety instructions in Section 1.
3.1. Start-up.
3.1.1. Place directly into the water. Put the pump on a horizontal surface, which is elevated by the edge of the basin to prevent the pump
from becoming excessively muddy.
Technical Data.
Model No: WPP1750S WPP3000S WPP3600S
Fountain Head Effects: Spume Spout 23cm 38cm 55cm
Water Clock Spout 42cm 70cm 85cm
Waterfall Spout 110cm/120cm 110cm 160cm
Outlet Size OD: 13mm 13mm 13mm
Maximum Output: 29ltr(6gal)/min 50ltr(10gal)/min 60ltr(13gal)/min
Maximum Head: 2.3mtr 3.2mtr 4mtr
Motor Power: 50W 85W 120W
Supply: 230V 230V 230V
Cable Length: 10mtr 10mtr 10mtr
3.2. Fountain Heads.
3.2.1. A selection of fountain heads are supplied with the pump (fig.2). Choose the desired style and install onto the outlet pipe.
3.3. Fountain and Water Spout Connection.
3.3.1. Additional water hose can be connected to the water spout connection (fig.1) with a hose of 19mm OD .
3.3.2. To open the spout connection, turn the regulating valve (fig.1) anticlockwise between 0-90° to adjust the flow between the spout and
the fountain head.
3.4. Water Spout Only.
3.4.1. Turn the regulating valve all the way clockwise to 90°. All the water flow will now be through the water spout.
fig. 1
fig. 2
Original Language Version
WPP1750S, WPP3000S, WPP3600S Issue: 2(L) - 30/06/16
© Jack Sealey Limited
Page 3
4. MAINTENANCE
WARNING! With the exceptions listed below, all pump and electrical cable service maintenance and repair must be
undertaken by an authorised service agent only. Failure to observe this rule may be dangerous and will invalidate your warranty.
WARNING!
Ensure that the pump is disconnected from the mains power supply before attempting any service or maintenance.
4.1. Cleaning the filter sponge.
4.1.1. Press the filter housing together on both sides, turn anticlockwise (fig.3) and pull off the cover.
4.1.2. Remove the sponge filter (fig.3) from the housing and clean with clean cold water.
Caution: Never use the pump without the filter in place as this could lead to damage to the pump.
4.2. Cleaning the functioning parts.
4.2.1. Open the pump chamber lid (fig.4) by twisting it anticlockwise and pulling it clear of the pump body. Remove the washer from the
bottom of the shaft.
4.2.2. Remove the magnetic impeller (fig.5) carefully from the shaft. As this is done the magnetic force of the impeller must be overcome.
There is a washer on the top end of the impeller shaft.
4.2.3. Do not use any implements to remove dirt from inside the pump, but simply wash it out with lukewarm water.
4.2.4. Use a soft sponge to remove any dirt deposits.
4.2.5. To reassemble the pump, check that the washer is fitted on the top end of the shaft, carefully slide the magnetic impeller onto the
shaft. At a certain point, the impeller will be drawn into the housing by the magnetic force.
4.2.6. Check that the rubber bearing (fig.5), at the end of the shaft, is correctly mounted.
4.2.7. Before closing the pump chamber with the lid make sure that its o-ring is correctly seated.
4.2.8. Plug the supply cable into the mains supply briefly (no more than 3 seconds) to check that the impeller turns freely. A certain level of
noise is inevitable during this dry run, this is no cause for concern. When it is used in water, the pump should operate silently.
4.3. Winter storage
4.3.1. Place the pump in water filled vessel in a frost free room. Storage in water prevents deposits from accumulating on the pump. If the
pump is stored dry, these deposits can block the impeller. If you wish to store the pump dry, you must ensure that the functioning
parts and filters have been thoroughly cleaned and dried.
4.3.2. DO NOT operate pump in temperatures of below 5°C.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
fig. 3 fig. 4
fig. 5
Environmental Protection.
Recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which
is compatible with the environment.
WEEE Regulations.
Dispose of this product at the end of its working life in compliance
with the EU Directive on Waste Electrical and Electronic Equipment.
When the product is no longer required, it must be disposed of in an
environmentally protective way. Contact your local solid waste
authority for recycling information.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or telephone 01284 757500.
Original Language Version
WPP1750S, WPP3000S, WPP3600S Issue: 2(L) - 30/06/16
© Jack Sealey Limited
Loading...