
INSTRUCTIONS FOR:
ReAR AXLe BUSH TOOL FORD FIeSTA IV, Ka
Model No: VSe4779.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLeASe ReAD THeSe INSTRUCTIONS CAReFULLY. NOTe THe SAFe OPeRATIONAL ReQUIRemeNTS, WARNINGS AND CAUTIONS.
USe THe PRODUCT CORReCTLY AND WITH CARe FOR THe PURPOSe FOR WHICH IT IS INTeNDeD. FAILURe TO DO SO mAY CAUSe
DAmAGe AND/OR PeRSONAL INJURY, AND WILL INVALIDATe THe WARRANTY. PLeASe KeeP INSTRUCTIONS SAFe FOR FUTURe USe.
1. SAFeTY INSTRUCTIONS
WARNING! Ensure Health and Safety, local authority and general
workshop practice regulations are adhered to when using tools.
DO NOT use tools if damaged.
Maintain tools in good and clean condition for best and safest
performance.
Ensure that the vehicle which has been jacked up is adequately
supported with axle stands.
Wear approved eye protection. A full range of personal safety
equipment is available from your Sealey dealer.
Wear suitable clothing to avoid snagging. Do not wear jewellery
and tie back long hair.
DO NOT use the tool for purposes other than for which it is
designed
DO NOT use the tool when you are tired or under the influence
of alcohol, drugs or intoxicating medication.
DO NOT use an impact wrench with this tool.
When not in use, store tool in a safe, dry childproof area.
IMPORTANT! These instructions are provided as a guide
only. Always refer to the vehicle manufacturer's service
instructions or a propriety manual, to establish the current
procedure and data.
WARNING: The warnings, cautions and instructions discussed in
this manual cannot cover all possible conditions and situations
that may occur. It must be understood that common sense and
caution are factors which cannot be built into this product, but
must be applied by the operator.
breakdown of this procedure refer to the vehicle manufacturer’s
service instructions, or a proprietary manual.
3.4 Thoroughly apply penetrating oil to each bush to aid extraction from
the bush housing.
3.5 To extract the old bush, assemble the tool onto the bush as shown
in Fig.2. Ensure that the screw rod (1) is well lubricated prior to
assembly. Hold the retention nut (2) with a 24mm ring spanner.
Using a ratchet wrench with a 24mm deep socket turn the nut on
the force nut assembly (6) clockwise to drive the bush out of its
housing.
2. INTRODUCTION & APPLICATION
2.1 Introduction: Remove/Install rear axle mounting bushes in Ford
Fiesta IV, Ka. Can be used in situ – no need to remove the rear
trailing link assembly from vehicle.
2.2 Applications: Ford Fiesta IV, Ka-1996 onwards.
Fig.1
ITem DeSCRIPTION
1 SCREW ROD
2 RETENTION NUT
3 PUSHING CUP
ITem DeSCRIPTION
4 RECEIVING CUP
5 INS ER TIO N C UP
6 FORCE NUT
3. OPeRATION
DO NOT use AN IMPAcT wReNch wITh ThIs TOOl.
3.1 Before working under the vehicle ensure that it is adequately
supported.
3.2 Thoroughly lubricate the screw rod threads each time the tool is
used.
3.3 Remove the rear wheels to gain access to the bush housings at
the top of each trailing arm. For a detailed and up to date
Original Language Version
Fig.2
3.6 To insert the new bush, assemble the tool and bush onto the bush
housing as shown in Fig.3. Ensure that the screw rod (1) is well
lubricated prior to assembly. Hold the retention nut (2) with a 24mm
ring spanner. Using a ratchet wrench with a 24mm deep socket turn
the nut on the force nut assembly (6) clockwise to drive the bush
into the housing.
Fig.3
VSE4779.V2 Issue: 1 - 24/11/11

ALWAYS KeeP SCReW ROD
WeLL LUBRICATeD.
DO NOT USe AIR TOOLS.
Screw rod maximum load 150Nm. exceeding this load will shorten the life of the screw rod. The screw rod is
considered to be a consumable item and is NOT covered under warranty.
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to
www.sealey.co.uk, email sales@sealey.co.uk or phone 01284 757500.
NOTe: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without
prior notice. ImPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of
which will be required for any claim. INFORmATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave
your full name and address, including postcode.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business
Park, Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
01284 757500
01284 703534
www.sealey.co.uk
Web
sales@sealey.co.uk
email
VSE4779.V2 Issue: 1 - 24/11/11