instructions for
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
tablet video borescope Ø5.5mm camera
model no: vs8223.v2
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
refer to
instructions
1. safety
9 Always perform automotive testing in a safe environment.
9 Keep your work area clean and well lit.
9 Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
9 operate the tool in a well-ventilated work area.
8 do not operate the tool in explosive atmospheres, such as in the presence of ammable liquids, gases, or heavy dust.
8 do not use the tool around corrosive chemicals which can damage the tool.
8 do not abuse the exible cable. Never use the exible cable to carry the tool.
8 do not drop the borescope, it is not shock proof.
9 Keep bystanders and children away while operating the tool.
9 Keep the tool dry, clean, free from oil, water and grease. use a small amount of mild detergent on a clean cloth to clean the outside
of the tool when necessary and store in a dry, childproof area.
9 Turn the borescope off when not in use.
9 Remove the batteries when cleaning the unit or before storing the unit for a long period of time.
9 When necessary replace all four batteries. Use only the size and type of battery specified.
2. introduction
fitted with large 110mm TFT screen and tablet design makes the image incredibly clear but also very portable. Includes the added advantage of
probe storage inside the rear of the case so no additional storage required. Features controls for light intensity, digital zoom, mirror ip function
and image rotation. Waterproof probe pod with IP67 rating and supplied in storage pouch. Powered by 4 x AA batteries (Supplied).
3. specification
model no ..............................................................Vs8223.V2
camera Ø ...................................................................5.5mm
field of Vision ...................................................................62
Pod length ...................................................................35mm
camera Probe Length ................................................830mm
Adjustable Light Control ...................................................Yes
screen Size ................................................................ 110mm
screen resolution .................................................... 480x272
mirror flip/rotate function ...............................................Yes
Power source ...............................................4xAA (supplied)
o
fig.1
© Jack sealey limited
Original Language Version
VS8223.V2 | Issue 1 30/10/17
VS8223.V2 | Issue 1 30/10/17
4. battery installation
4.1. Turn unit over to expose back. Press in the plastic tab on the right middle of the back cover and lift up to open.
4.2. Use a screwdriver to remove the screw in bottom middle of the battery cover.
4.3. Remove cover and insert 4AA batteries as shown inside the compartment.
4.4. replace screw.
fig.2 fig.3
5. operation
This borescope inspection camera unit comes fully assembled. Before rst use, carefully peel off the plastic label over the LCD.
5.1. To begin use, carefully uncoil the camera probe assembly coiled around the battery compartment.
5.2. Once probe is fully extended, align the cable with the opening on the upper right of the backside of the unit.
5.3. Align and replace the cover inserting the left hand tabs into the housing rst.
5.4. Press down to ensure a good t, making sure the cable ts through the opening.
5.5. Turn unit over, press and hold the power button for 3 seconds to turn on.
5.6. Point the camera-tipped end of the probe at the target, feed the probe through any holes or bend the probe around objects if necessary.
8 do not forcefully bend, kink, or pull the probe, this will damage it.
5.7. Use the function buttons as described in g.1 to set light output, screen size, zoom and viewing orientation.
5.8. Press and hold power button again for 3 seconds to turn off.
6. maintenance
6.1. Make sure the screws are properly tightened to be able to work safely. Use only original accessories and original spare parts.
6.2. If the device is not used, it should be stored in a dry place, away from children.
6.3. If the cable is damaged, replace it with another one which has the same characteristics. Entrust this operation to a qualied technician or
a repair shop.
6.4. All defects should be repaired by a service workshop authorized by the manufacturer.
environment protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Weee reGulations
dispose of this product at the end of its working life in compliance with the eu directive on Waste electrical and electronic equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
battery removal
refer to section 4. Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential
purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered
compliance scheme. Jack Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.
note: it is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
sealey Group, Kempson Way, suffolk business park, bury st edmunds, suffolk. ip32 7ar
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
© Jack sealey limited
Original Language Version
VS8223.V2 | Issue 1 30/10/17
Loading...