brake fluid tester
I
MPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
model no: Vs027.V3
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
Refer to
instruction
manual
Wear eye
protection
Wear
protective
gloves
fig.1
1. safetY
1.1. GeNeral safetY
88 88 dO NOt use the tester to perform a task for which it is not designed.
88 88 dO NOt allow untrained persons to use the tester.
88 88 dO NOt use whilst under the inuence of drugs, alcohol or intoxicating
medication.
89 88 Keep children and unauthorised persons away from the work area.
89 88 Keep work area clean and tidy and free from unrelated materials.
89 88 ensure the work area has adequate lighting.
89 88 After use, clean equipment and store in a cool, dry, child proof area.
8 88 WarNiNG!8Brake uid is ammable - keep away from sources of
ignition, including hot surfaces e.g. exhaust manifold.
1.2. brake fluid safetY
8 88 WarNiNG!8Brake uid will damage paintwork. Any spillage should be
ushed with water immediately.
9 Always read and comply with the warnings on the brake fluid container.
9 Wear eye protection and keep skin contact to a minimum. If brake fluid
enters eyes rinse with plenty of water and seek medical advice.
9 If swallowed seek medical advice immediately.
9 dispose of waste fluid in accordance with local authority regulations.
2. iNtrOductiON
Comparative electrolytic type tester. Checks moisture content of uid by resistance to electric current. Easily calibrated using new brake uid.
Audible test cycle with three LED read-out. Just insert probe and press button for immediate result. Works on DOT4 and 5.1 specication uids.
Uses 9V battery (not included).
3. specificatiON
Model No: .....................................Vs027.V3
moisture Content:
Green: ...........................................<0.5%
Yellow: ........................................0.5 - 3.5%
Red: .............................................>3.5%
4. preparatiON
4.1. battery installation
4.1.1. Open battery compartment at back of tester, g.2 and insert PP3 or equivalent observing correct polarity.
4.2. calibration
4.2.1. Unfold the test bar.
4.2.2. Clean the two probes on the test bar head (g.3)
4.2.3. Dip the test bar head into a sample of uid drawn from a container which was previously unopened and sealed (g.3). This is
particularly important as this uid will used as the reference against which subsequent samples are compared.
4.2.4. Press and hold the test button and turn the reset screw anticlockwise fully (g.4). All the LED’s should now be unlit.
4.2.5. Turn the reset screw clockwise until the green LED lights. The calibration procedure is now complete.
fig.2
fig.3
fig.4
© Jack Sealey Limited
Original Language Version
VS027.V3 | Issue:1 27/02/18
5. OperatiON
NOte: This tester is intended to provide a quick indication of the moisture content of brake uid. For a more precise measure we
recommend the use of a device which measures the boiling point of the uid, such as the Sealey VS0271 or VS0275.
5.1. Unfold the test bar and dip the head into the brake uid reservoir.
5.2. Press the test button for ve seconds and observe the LED indications:
GreeN: Moisture content below 0.5%; brake uid good.
YellOW: moisture content between 0.5% and 3.5%; brake uid poor. Replacement is recommended. If uid is not replaced: a further
check with a device measuring brake uid boiling point is recommended.
red: Moisture content above 3.5%. This should be regarded as an indication that the brake uid is unsafe and should be
replaced.
5.3. if iN aNY dOubt replace tHe brake fluid.
batterY reMOVal refer tO 4.1
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.
eNVirONMeNt prOtectiON
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
sealey Group, kempson Way, suffolk business park, bury st edmunds, suffolk. ip32 7ar
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
VS027.V3 | Issue:1 27/02/18
Loading...