instructions for
I
MPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
eLeCTRONIC STeTHOSCOPe
model no: VS0071
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
refer to
instruction
manual
Wear eye
protection
1. SAFeTY
WARNING! ensure Health & safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
9 familiarise yourself with the application and limitations of the equipment, as well as the specific potential hazards.
9 maintain the equipment in good condition
9 Keep the equipment clean for best and safest performance.
9 ensure cables and probe cannot contact moving parts.
8 DO NOT place cables and probe near high voltage items - Ht leads, spark plugs or ignition coil.
8 DO NOT allow untrained persons to operate the Vs0071.
8 DO NOT allow children to play with the Vs0071.
8 DO NOT operate the equipment when you are tired or under the influence of alcohol, drugs or intoxicating medication.
9 When not in use switch off equipment and store in a safe, dry, childproof area.
9 for prolonged storage, remove battery.
2. INTRODuCTION
Accurately pinpoints automotive noises and vibrations, which are converted into an electrical signal and amplied. Long pick up shaft allows use
in hard to reach places. features a volume control and supplied with headphones.
3. SPeCIFICATIONS
model no: .................................................................. Vs0071
Battery: ............................................................... 9V supplied
4. OPeRATION
4.1. remove battery compartment door on rear and connect battery.
4.2. Screw probe into head of amplier.
4.3. Fit headphone plug into socket in the base of the amplier and put headset on.
4.4. Switch unit on by initial movement of thumb wheel. Red LED conrms that unit is switched on.
4.5. further movement of the thumb wheel increases the headset volume; about half volume is the optimum setting for initial use.
increasing the volume may be necessary for faint sounds, but an increase in background noise will also occur.
4.6. Place the tip of the probe against the suspect part, taking care to comply with safety instructions in section 1.
4.7. the sound pitch and quality will vary, giving an indication of the location and severity of any potential problem.
WARNING! Prolonged exposure to high volumes of noise, or sudden very loud noises can result in permanent hearing loss.
5. MAINTeNANCe
5.1. renew battery with a similar 9V item, refer to section 4.1.
5.2. clean with a damp cloth and a mild detergent DO NOT use solvents.
8 DO NOT allow unit to become wet, store in a cool, dry place.
© Jack sealey limited
Original Language Version
Vs0071 | issue:2 (H, 4, l) 02/02/18
Weee ReGuLATIONS
dispose of this product at the end of its working life in compliance with the eu directive on Waste electrical and electronic equipment
(Weee). When the product is no longer required, it must be disposed of in an environmentally protective way. contact your local solid
waste authority for recycling information.
BATTeRY ReMOVAL ReFeR TO SeCTION 4.1. under the Waste Batteries and Accumulators regulations 2009, Jack sealey ltd are
required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with
Valpak’s registered compliance scheme. Jack sealey ltd Batteries Producer registration number (BPrn) is BPrn00705.
eNVIRONMeNT PROTeCTION
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: it is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
© Jack sealey limited
Original Language Version
Vs0071 | issue:2 (H, 4, l) 02/02/18
Loading...