INSTRUCTIONS FOR:
TEST LEAD KIT 92PC
MODEL No: TA111.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,
give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. PLEASE KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1. PERSONAL PRECAUTIONS.
When using the test leads, observe all normal safety rules concerning:
Protection against the dangers of electric current.
Protection of the test leads against misuse.
DO NOT use leads if damaged or if the internal wire is exposed in
any way.
1.2. GENERAL SAFETY INSTRUCTIONS.
WARNING! Never perform resistance measurements on live circuits.
Only measure on disconnected circuits.
These test leads are designed to be used on automotive circuits only.
DO NOT use on 110V and 230V applications.
Familiarise yourself with the application and limitations of the test
leads as well as the potential hazards.
IF IN ANY DOUBT CONSULT A QUALIFIED ELECTRICIAN.
When not in use, store the test leads in the case supplied.
Keep the work area clean, uncluttered and ensure there is adequate
lighting. Keep tools and other items away from the engine and ensure
that you can see the working parts of the engine clearly.
Observe standard workshop safety procedures when using the test
leads.
Consult the vehicle's handbook for fuse positions and check if the fuse
hasblown.Ifthefusehasblown,rstestablishthereasonforthis
before replacing with the same fuse type.
Ensure test leads are kept clear of hot surfaces and rotating parts.
Never apply voltage or current to the test leads that exceeds the
specified maximum.
DO NOT use the test leads for any purpose other than for which they
are designed.
DO NOT get the test leads wet, or use in damp or wet locations or
areas where there is condensation.
3. CONTENTS
Both flat and round terminals are available as shown below. Each male or
female connector is attached to a short lead with a 4mm banana socket at
the other end. Each lead is supplied in quantities of 3, other connectors
are shown overleaf.
fig.1
2. INTRODUCTION
Comprehensive set of test leads and components suitable for testing,
isolating and evaluating automotive electronic circuits. Kit includes standard
Ø4mm banana style plugs and sockets suitable for use with most diagnostic
multimeters and test equipment. Supplied in sectioned carry-case for quick
location of components.
3.1. FLAT TERMINALS (fig.1)
0.7mm (Male/Female) + Female banana sockets (3pcs each)
0.8mm (Male/Female) + Female banana sockets (3pcs each)
1.2mm (Male/Female) + Female banana sockets (3pcs each)
2.0mm (Male/Female) + Female banana sockets (3pcs each)
2.5mm (Male/Female) + Female banana sockets (3pcs each)
3.0mm (Male/Female) + Female banana sockets (3pcs each)
5.0mm (Male/Female) + Female banana sockets (3pcs each)
6.0mm (Male/Female) + Female banana sockets (3pcs each)
© Jack Sealey Limited
fig.2
3.2. ROUND TERMINALS (fig.2)
1.5mm (Male/Female) + Female banana sockets (3pcs each)
2.0mm (Male/Female) + Female banana sockets (3pcs each)
3.5mm (Male/Female) + Female banana sockets (3pcs each)
4.0mm (Male/Female) + Female banana sockets (3pcs each)
Original Language Version
TA111.V2 ISSUE No:1 07/06/13
fig.3
fig.7
3.3. ALLIGATOR CLIPS
Two clips are supplied, one red (positive) and one black (negative).
The banana sockets at the back of the terminals will accept the leads
supplied or the probe (fig.7). Quantity: 2.
fig.4
3.4. 1 to 2 CONNECTOR
Allows a one to two connection. Quantity: 2.
fig.5
3.5. LED STROBOSCOPE
Two colour, two way LED. LED changes colour in response to the
polarity. Quantity: 2.
3.7. PROBE
The probe has a 4mm banana socket in the end of the barrel thus
allowing connectivity with other components in the system.
Quantity: 2.
fig.8
3.8. MALE/FEMALE 1 to 1 CONNECTOR
Connectors are at either end of 100cm leads and allow a one to one
piggy-back connection. Quantity: 4.
fig.9
3.9. 5KW POTENTIOMETER
Use in conjunction with various sensors such as those for engine
coolant temperature, oil temperature etc. Quantity: 2.
fig.6
3.6. SRS CONNECTOR
Aids the setting up of a new SRS airbag and seat belt triggers after
an accident. Maximum current 0.25A, above this value the
connector will burn out. Quantity: 2.
fig.10
3.10. BACK PROBE
U
open circuit, break or bad connection.
se these probe to pierce wire insulation to allow to test closer to an
Quantity: 4.
4. PARTS
ITEM PART NO: DESCRIPTION
1 TA111.01 4.0mm ROUND TERMINAL (M) WIRE
2 TA111.02 3.5mm ROUND TERMINAL (M) WIRE
3 TA111.03 2.0mm ROUND TERMINAL (M) WIRE
4 TA111.04 1.5mm ROUND TERMINAL (M) WIRE
5 TA111.05 0.8mm FLAT TERMINAL (F) WIRE
6 TA111.06 1.2mm FLAT TERMINAL (F) WIRE
7 TA111.07 2.0mm FLAT TERMINAL (F) WIRE
8 TA111.08 2.5mm FLAT TERMINAL (F) WIRE
9 TA111.09 3.0mm FLAT TERMINAL (F) WIRE
10 TA111.10 5.0mm FLAT TERMINAL (F) WIRE
11 TA111.11 6.0mm FLAT TERMINAL (F) WIRE
12 TA111.12 6.0mm FLAT TERMINAL (M) WIRE
13 TA111.13 5.0mm FLAT TERMINAL (M) WIRE
14 TA111.14 3.0mm FLAT TERMINAL (M) WIRE
15 TA111.15 2.5mm FLAT TERMINAL (M) WIRE
16 TA111.16 2.0mm FLAT TERMINAL (M) WIRE
17 TA111.17 1.2mm FLAT TERMINAL (M) WIRE
18 TA111.18 0.8mm FLAT TERMINAL (M) WIRE
19 TA111.19 1.5mm FLAT TERMINAL (F) WIRE
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
ITEM PART NO: DESCRIPTION
20 TA111.20 2.0mm FLAT TERMINAL (F) WIRE
21 TA111.21 3.5mm FLAT TERMINAL (F) WIRE
22 TA111.22 4.0mm FLAT TERMINAL (F) WIRE
23 TA111.23 ALLIGATOR CLIPS (RED)
24 TA111.24 ALLIGATOR CLIPS (BLACK)
25 TA111.25 LED STROBOSCOPE
26 TA111.26 1 TO 2 CONNECTOR
27 TA111.27 PROBE (RED)
28 TA111.28 PROBE (BLACK)
29 TA111.29 BACK PROBE (RED)
30 TA111.30 BACK PROBE (BLACK)
31 TA111.31 SRS CONNECTOR
32 TA111.32 5K POTENTIOMETER (VARIABLE RESISTOR)
33 TA111.33 1 TO 1 CONNECT WIRE (RED)
34 TA111.34 1 TO 1 CONNECT WIRE (BLACK)
35 TA111.35 CASE
36 TA111.V2.36 0.7mm FLAT TERMINAL (F) WIRE
37 TA111.V2.37 0.7mm FLAT TERMINAL (M) WIRE
© Jack Sealey Limited
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk, IP32 7AR
Original Language Version
01284 757500
01284 703534
www.sealey.co.uk
Web
sales@sealey.co.uk
TA111.V2 ISSUE No:1 07/06/13
Loading...