INSTRUCTIONS FOR:
LOCKING WHEEL NUT REMOVAL SET 10pc
MODEL NO:SX272
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Instruction
Manual
Wear Eye
Protection
Wear Protective
Gloves
1. SAFETY
WARNING! DO NOT use the tool if damaged or thought to be faulty.
WARNING! Ensure that Health & Safety, Local Authority Regulations and general workshop practice Regulations are adhered to
when using tools.
WARNING! If jacking up a vehicle refer to manufactures instructions for vehicle and jack.
8 DO NOT use the tool for a task it is not designed to perform.
8 DO NOT use worn, or damaged sockets.
8 DO NOT use the tool unless you have been instructed in its use by a qualied person.
8 DO NOT operate the tool if you are tired or under the inuence of alcohol, drugs or intoxicating medication.
9 Maintain the tool in good condition.
9 Follow all workshop safety rules, regulations and conditions.
9 Maintain correct balance and footing. Ensure the oor is not slippery and wear non-slip shoes.
9 Keep children and non essential persons away from the working area.
2. INTRODUCTION
Conical shaped design allows socket to fit over locking/wheel nut. Socket is hammered onto nut using the punch, so nut and socket wedge
together. Nut can then be removed with a breaker bar or impact wrench. Set also includes drift to remove nut from socket.
3. SPECIFICATION
Model No: ....................................................................SX272
Drive: .....................................................................22mm Hex
Maximum Internal Sizes: ..........................Ø18, 19.3, 20, 21.3, 22.3, 23.3, 24.3, 25.2mm
© Jack Sealey Limited
Original Language Version
SX272 Issue: 1 - 04/05/17
4. OPERATION
4.1. Select the appropriate removal socket to create a tight fit over the wheel nut.
4.2. Fit the socket over the wheel nut and insert the punch (fig.1).
4.3. Using a suitable hammer, strike the punch sharply several times until the socket has gripped the wheel nut.
4.4. Place either a wrench or impact socket over the hex at the rear of the removal socket.
4.5. Release the wheel nut by turning as a unit with the removal socket.
4.6. Hold the removal socket in a vice and pass the drift through the rear end of the socket and strike the drift to release the wheel nut (fig.2)
WARNING: Take care when removing the nut from the removal socket: the nut can exit the socket with considerable force
g.1
g.2
5. MAINTENANCE
5.1. Clean the inside of the socket with abrasive paper or cloth to remove any dirt or irregularity.
5.2. Keep the kit clean and store all the components in the case after use.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, dispose of it according to local regulation
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
Environmental Protection
s.
NOTE: It is our policy to improve products continually and as such we reserve the right to alter data, specifications and component parts without
prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey Limited
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
01284 757500
01284 703534
www.sealey.co.uk
sales@sealey.co.uk
SX272 Issue: 1 - 04/05/17
Loading...