Sealey SMS2003 Instructions Manual
INSTRUCTIONS FOR:
SAW BLADE SHARPENER - BENCH MOUNTING 110W
MODEL No: SMS2003
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1. ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also
recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are
plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections
to ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation
extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol
To rewire, connect the wires as indicated above DO NOT connect either wire to the earth terminal.
1.1.10. Products which require more than 13Amps are supplied without a plug. In this case you must contact a qualified electrician to ensure that
a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your
electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm
1.2. GENERAL SAFETY
WARNING! Disconnect the saw blade sharpener from the mains power, and ensure that the cutting disc is at a complete standstill before
attempting to service or perform any maintenance.
Maintain the saw blade sharpener in good condition (use an authorised service agent).
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Locate the saw blade sharpener in a suitable work area. Bolt securely to the workbench through the four holes on the base. Ensure that
the surface is flat and capable of supporting the weight of the sharpener (see fig.1). Keep the area clean and tidy and free from unrelated
materials, and ensure that there is adequate lighting.
Keep the saw blade sharpener clean for best and safest performance and check moving parts alignment regularly.
WARNING! Before each use check that the grinding stone is secure and that it is not worn or damaged. Test the grinding stone by
running it for a minute prior to its use. NOTE: Only competant persons should attempt to change grinding stones.
Ensure that replacement stones are not damaged in any way - cracks or deformations etc. Also check the mounting flanges to check that
they are not deformed, burred or chipped. DO NOT over tighten a stone and never tamper with a stone in order to adapt it to a different
size holder.
WARNING! Never operate the sharpener without the grinding wheel cover in place.
Ensure that replacement grinding wheels meet the speed rating of the tool.
WARNING! This machine is designed to sharpen saw blades. DO NOT attempt to sharpen any other tools and DO NOT attempt to
grind any other objects.
WARNING! Wear approved safety eye protection, ear defenders and gloves.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the work area.
2
section cable.
, are fitted with live (brown) and neutral (blue) wires only.
2
, but to be absolutely sure that the
RECOMMENDED
FUSE RATING 5AMP
© Jack Sealey Limited
Original Language Version
SMS2003 Issue: 1 27/02/14
WARNING! Keep away from the grinding wheel when it is turning, and make sure no one is standing close in the line of the grinding wheel
trajectory.
DO NOT allow untrained persons to operate the saw blade sharpener.
DO NOT get the machine wet, or use in damp or wet locations or areas where there is condensation.
WARNING! DO NOT use the saw blade sharpener where there are flammable liquids, solids or gases such as paint solvents and including waste
wiping rags etc.
DO NOT operate the saw blade sharpener if any parts are missing or damaged as this may cause failure and/or personal injury.
DO NOT operate the saw blade sharpener when you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use switch off the saw blade sharpener and remove the plug from the power supply.
2. INTRODUCTION & SPECIFICATIONS
Suitable for sharpening TCT saw blades ranging from Ø90 to Ø400mm. Fitted with a Ø100mm diamond coated grinding disc for optimising
saw blade performance. Precision 0-25° angle adjustment allowing each tip to be sharpened exactly the same. Quick and easy to use, whilst
saving money on having to constantly buy new blades.
Specifications:
Model No: ................... SMS2003
Motor Power: ..............110W - 230V
Free Speed: ..................5300rpm
Wheel Diameter:................ 100mm
Minimum Blade Diameter: .........90mm
Maximum Blade Diameter:........ 400mm
Angle Adjustment: ................0-25°
Weight: ..........................5kg
3. CONTENTS
Unpack the product and check the contents. Ensure that there is no damage. If any problem is noted, contact your supplier immediately.
Fig.1
4. OPERATION
Before sharpening saw blades ensure that you wear approved safety goggles, ear defenders, and safety gloves. All safety
instructions in Section 1 must be followed.
WARNING! Always ensure that the machine is switched off before connecting the plug to the socket and always disconnect before
carrying out any work on the machine.
4.1. Remove the knob, all washers, the spring and the centring piece from the saw blade holder.
4.2. Put the saw blade (which needs to be sharpened), on the bolt and reassemble in the order indicated on the picture below. (See fig.2).
Fig.2
4.3. The saw blade only needs to be centred but not tightly xed. Screw down the fastening knob only as much as necessary for sufcient
tension, so that the saw blade can still be turned. Make sure that the centring piece is not slanted. (See g.2).
© Jack Sealey Limited
Original Language Version
SMS2003 Issue: 1 27/02/14
Loading...