Sealey SMC11, SMC12 Instruction Booklet

INSTRUCTIONS FOR
I
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
BATTERY CHARGER COMPACT AUTO MAINTENANCE-3-CYCLE 12V
MODEL NO: SMC11 & SMC12
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
Refer to instructions
Keep in dry area
protect from rain
Wear eye protection
Wear protective
gloves
Electrical shock hazard
Warning
corrosive
substance
Warning: explosive
material
Keep away
from sources of
ignition
Use in well
ventilated areas
1. SAFETY
Electrical Safety
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical products. You may obtain an RCD by contacting your local Sealey dealer. If the charger is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood. 9 Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. 9 Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure. 9 Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is tted with the
correct fuse - see fuse rating in these instructions. 8 DO NOT pull or carry the appliance by the power cable. 8 DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a rm grip on the plug. 8 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualied electrician.
This product is tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualied electrician.
Class II products are wired with live (brown) and neutral (blue) only and are marked with The Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’. B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
8 DO NOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualied electrician.
DANGER! BE AWARE, LEAD-ACID BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION.
FOR THIS REASON, IT VERY IMPORTANT TO READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY, EACH TIME YOU USE
THE CHARGING EQUIPMENT.
9 Follow these instructions and those published by the battery and vehicle manufacturers, and the maker of any equipment you intend to
use in the vicinity of the battery. Remember to review warning marks on all products and on engines.
WARNING! Modern vehicles contain extensive electronic systems.
You are required to check with the vehicle Manufacturer, for any specic instructions regarding the use of this type of equipment on
each vehicle.
No liability will be accepted for damage / injury, where this product is not used in accordance with all instructions.
© Jack Sealey Limited
Original Language Version
SMC11,SMC12 | Issue 2 (3, F) 02/05/18
Recommended fuse rating
3 Amp
1.1. Personal Precautions
9 Ensure there is another person within hearing range of your voice and close enough to come to your aid, should a problem arise when
working near a lead-acid battery. 9 Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery. 9 Have fresh water and soap nearby in case battery acid contacts skin, clothing or eyes. 9 Wash immediately with soap and water if battery acid contacts skin or clothing. If acid enters eye, flush eye immediately with cool, clean
running water for at least 15 minutes and seek immediate medical attention.
9 Remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit current
which is high enough to weld a ring or the like to metal, which would cause severe burns. 9 Ensure hands, clothing (especially belts) are clear of fan blades and other moving or hot parts of engine, remove ties and contain long hair.
8 DO NOT smoke or allow a spark or flame in the vicinity of battery or engine.
1.2. General Safety Instructions
9 Familiarise yourself with the application and limitations of the charger as well as the potential hazards. Also refer to the vehicle
manufacturer’s hand book. IF IN ANY DOUBT CONSULT A QUALIFIED ELECTRICIAN.
9 Ensure the charger is in good order and condition before use. If in any doubt do not use the unit, contact your Sealey Stockist. 9 Use the charger in the upright position only and ensure it is placed on a stable surface which will adequately support its weight. 9 Ensure the charger is disconnected from the mains supply before attaching/detaching the power clamps to/from the battery. 9 Keep tools and other items away from the engine and ensure you can see the battery and working parts of engine clearly. 9 Ensure the output of the charger is the same voltage as the battery. 9 Ensure that during charging, the charger is placed in a location where there is sufficient ventilation to prevent the build up of explosive
gases from a lead acid battery.
9 If battery has caps to access the battery fluid, remove the caps and check the fluid level before connecting the power clamps. If
necessary top-up the battery with distilled water by referring to the battery manufacturer’s instructions (Apply the personal
safety precautions described in part 1.2).
9 If the charger receives a sharp knock or blow the unit must be checked by a qualified service agent before using. 9 If the battery terminals are corroded or dirty clean them before attaching the power clamps. 9 Keep children and unauthorised persons away from the working area.
8 DO NOT dis-assemble the charger for any reason. The charger must only be checked by qualified service personnel. 8 DO NOT try to charge a non-rechargeable battery. 8 DO NOT try to start engine when charger is connected to battery. 8 DO NOT try to charge battery if battery fluid is frozen.
WARNING! To prevent the risk of sparking, short circuit and possible explosion DO NOT drop metal tools in the battery area, or allow
them to touch the battery terminals.
8 DO NOT allow power clamps to touch each other or to make contact with any metallic part of the vehicle. 8 DO NOT cross connect power leads from charger to battery. Ensure positive (+/RED) is to positive and negative (-/BLACK) is to negative. 8 DO NOT pull the cables or clamps from the battery terminals. 8 DO NOT use the charger outdoors, or in damp, or wet locations and DO NOT operate within the vicinity of flammable liquids or gases. 8 DO NOT use charger inside vehicle or inside engine compartment.
9 Ensure there is effective ventilation to prevent a build-up of explosive gases.
8 DO NOT use the charger for a task for which it is not designed.
WARNING! DO NOT simultaneously charge batteries of different capacities or discharge levels. WARNING! DO NOT charge a frozen battery. WARNING! If a fuse blows, ensure it is replaced with an identical fuse type and rating. Use only Sealey genuine parts.
9 When not in use, store the charger carefully in a safe, dry, childproof location.
NOTE:This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
2. INTRODUCTION
Fully automatic multi-cycle switch mode chargers and maintainers designed for charging a variety of batteries: SLA, WET, AGM/GEL and VRLA. Chargers will recover slightly sulphated batteries and may rescue drained batteries. With the SMC13 and SMC14 the digital display lets you know
exactly how the charger is performing and indicates the charging or maintenance phase and battery voltage. Supplied with multi-fit charger cables featuring crocodile clips and hard-wired terminals incorporating a water tight plug and socket for permanent installation - great for motorcycles and cars.
3. SPECIFICATION
Model No.............................................................................SMC11.....................................SMC12
Type..............................................................................3-Cycle12V..............................3-Cycle 12V
Input........................................................................................230V.........................................230V
Output.......................................................................................12V...........................................12V
Input Current..........................................................................0.25A........................................0.25A
Efciency................................................................................>80%........................................>80%
Charging Current.....................................................................0.8A..........................................1.5A
Back Current Drain......................................................<1Ah/month.............................<13Ah/month
Ambient Temperature..............................................-20°C to +50°C ........................-20°C to +50°C
Dimensions (LxWxH)................................................178x66x38mm ....................198 x 68 x 41mm
Housing Protection..................................................................IP20.........................................IP65
Weight....................................................................................0.4kg..................................... 0.49kg
© Jack Sealey Limited
Original Language Version
SMC11,SMC12 | Issue 2 (3, F) 02/05/18
Loading...
+ 1 hidden pages