Sealey SM1310 Instructions Manual

INSTRUCTIONS FOR:

PLANER 150MM

MODEL No: SM1310

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1.1 ELECTRICAL SAFETY

  WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also
recommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are
plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.

1.1.1 The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2 The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition
of those appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.

1.1.3 Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power
supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester.

1.1.4 Ensure that cables are always protected against short circuit and overload.

1.1.5 Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.

1.1.6 Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.

1.1.7 DO NOT pull or carry the appliance by the power cable.

1.1.8 DO NOT pull the plug from the socket by the cable.

Blue
Neutral
Wire

1.1.9 DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.

Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.
To rewire, connect the wires as indicated above.
DO NOT connect either wire to the earth terminal.

1.1.10 Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.

1.1.11 If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.

Yellow & Green
Earth Wire

Brown
Live
Wire

Cable
Restraint

FUSE RATING:

THIS PRODUCT MUST BE

FITTED WITH A 13 AMP FUSE

1.2 General Safety

 WARNING!Disconnect the planer from the mains power before changing accessories, servicing or performing any maintenance.
 Locate the planer in a suitable working area. Use the planer on a strong flat working surface. Keep area clean and tidy and free from

unrelated materials and ensure there is adequate lighting.

 Maintain the planer in good condition (use an authorised service agent).
 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
 Keep the planer clean for best and safest performance and check moving parts alignment regularly.
 Wear approved eye safety protection.
 Handle loose blades with gloves or cloth as they are very sharp, but DO remove gloves and/or cloth before operating the planer.
 Keep your hands and fingers away from the blade when operating.
 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Ensure there are no foreign objects in the workpiece i.e. nails or screws.
 DO NOT start the planer with the workpiece touching the blade.
 DO NOT use the planer for a task it is not designed to perform.
 DO NOT allow untrained persons to operate the planer and keep children and unauthorised persons away from the working area.
 DO NOT get the planer wet or use in damp or wet locations or areas where there is condensation.
 DO NOT use planer where there are flammable liquids, solids or gases such as paint solvents, waste wiping or cleaning rags etc.
 DO NOT operate the planer if any parts are damaged or missing as this may cause failure and/or possible personal injury.
 DO NOT leave the planer operating unattended.
 DO NOT operate the planer when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT use the machine without the appropriate guard in place and ensure it is correctly adjusted.
 DO NOT use blades, which are blunt as this increases the danger of kickback.
 Any portion of the cutter block not being used for planning shall be guarded.

Original Language Version

SM1310 Issue: 2 - 23/11/09

 When planing short workpieces, a push-stick should be used.
 Check for alignment of moving parts, binding of moving parts, mounting and any other conditions that may affect it's operation.
 If a guard or other part is damaged it should be properly repaired or replaced by an authorized service centre unless otherwise indicated in

this instruction manual.

 Stay alert - Watch what you are doing, use common sense and do not operate the tool when you are tired.
 When not in use switch off the planer and remove plug from the power supply.

NOTE! Max. allowable blade projection over cutterblock 1.0mm/0.004 inch +10%.

2. APPLICATION & SPECIFICATION

Portable power planer with heavy-duty cast base for accurate and smooth planing. Accurate fence tilts between 45° and 90°. Fitted with two
blades capable of planing timber up to 150mm wide. No-volt release switch prevents uncontrolled re-start after power interruption. Dust
extraction port with collection bag. Adjustable cutting depth up to 3mm.

Motor ..................................1100W, 230V 50Hz.

Maximum cut (width x depth) .......................150 x 3mm

Cutter-head Speed ................................10000rpm

Fence Angle ........................................45-90°

Working Table Size.............................650 x 160mm

Weight .............................................17kg

FIG. 1

A

B

3. ASSEMBLY

3.1 ASSEMBLY

 WARNING! DO NOT plug the planer into the mains power
supply until completely assembled.
DO NOT allow brake fluids, petroleum, penetrating oils etc. to
come into contact with plastic parts of planer as damage may
result. The machine is shipped nearly complete in one carton.
Additional parts which need to be fastened to machine should
be located and accounted for before assembling. (fig. 1).

A. Planer
B. Angle fence
C. 4mm Hex wrench
D. 5mm Flat washer
E. 5mm Lock washer
F. Hex head bolt
G. Bag clamp
H. Dust collection bag

3.2 SETTING ANGLE FENCE (fig. 2)

3.2.1 Insert screw into the slot (A), then locate the fence on screw
(C). Securely tighten screw (A) first, then screw (C).
Angle adjustment is made by loosening knob (D) and
tilting fence to the desired angle using scale (B). Re-tighten
knob (D) fig. 2.

3.3 SETTING SAFETY GUARD (fig. 3)

3.3.1 To adjust the height of the guard, loosen knob A, raise
or lower the guard (B), until it is in firm sliding contact with the
workpiece. Tighten knob A.

3.3.2 After adjusting the guard height it can be adjusted sideways
to set the required stock width for jointing. (As in Fig.4)

ATTENTION: Make sure that the switch is in off position before
adjusting the cutting depth, replacing or adjusting the blades. Make
sure the blade screws are securely tightened.

FIG. 2

A

B

FIG. 3

G

H

C
D

E
F

C

D

A

Original Language Version

B

SM1310 Issue: 2 - 23/11/09