aIR OPERaTED PaNEL DRYER
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
WITH aDJUST aBLE aIRFLOW
mODEL NO: SDa01
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
Refer to
instruction
manual
Wear
eye protection
Wear
protective
clothing
Wear
a mask
1. SaFETY
9 Familiarise yourself with this products application and limitations.
WaRNING! Disconnect from the air supply before performing any maintenance.
9 maintain the dryer in good condition (use an authorised service agent).
9 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9 Locate the dryer in an adequate working area for its function, keep area clean and tidy and free from unrelated materials, and ensure
there is adequate ventilation and lighting.
9 Keep the dryer clean for best and safest performance.
9 Ensure the air system is suitable to the dryer consumption, (see specifications).
9 Wear approved respiratory protection and safety eye goggles.
9 Keep children and unauthorised persons away from the working area.
9 When not in use ensure the air supply is turned off.
9 Avoid unintentional operation.
8 DO NOT use the dryer for any purpose other than for which it is designed.
8 DO NOT operate dryer if any parts are missing or damaged as this may cause failure or personal injury.
8 DO NOT direct air from the air hose at yourself or others.
9 When not in use switch the dryer off, and disconnect from the air supply.
2. INTRODUcTION
Designed for drying water based paints. Operates on workshop air supply. Filter prevents airborne particles contaminating paint surface.
Adjustable airow to regulate as required. Ideal for localised or spot repair. May be hand held or mounted on optional Double Support Stand Model no: SDAST.
3. SPEcIFIcaTION
model no .....................................................................SDA01
Standard set up ...........................................................1.4mm
max. working pressure .................................................. 90psi
Air consumption ........................10cfm@15psi, 20cfm@90psi
Air inlet ......................................................................1/4”BSP
4. aIR SUPPLY
4.1. air Supply
4.1.1. Ensure spray dryer air valve is in the “off” position before connecting to the air supply.
4.1.2. You will require an air pressure of 90psi, and an air flow according to specification.
WaRNING! Ensure the air supply is clean and does not exceed 90 psi while operating the dryer. Too high an air pressure and
unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.3. Drain the air tank daily. Water in the air line will ruin the paint finish and damage the dryer.
4.1.4. Clean air inlet filter weekly. Recommended hook-up procedure is shown in (fig.1).
4.1.5. Keep hoses away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections are secure.
4.2. couplings
4.2.1. movement can cause failure if a quick change coupling is connected directly to the dryer when used without optional stand,
model No. SDAST. To overcome this, connect a leader hose to the dryer. A quick change coupling may then be used to connect the
leader hose to the air line recoil hose. (See g’s.1 & 2).
Fig. 1
© Jack Sealey Limited
Original Language Version
Fig. 2
SDA01 | Issue: 3 (H,3,F) 30/08/18
5. OPERaTION
5.1. Connect dryer to air supply as described in section 3.
5.2. Ensure the valve is in the ‘OFF’ (fig.3) position and turn on the air supply.
5.3. Open the valve (fig.3) to proceed, you can regulate the air flow by the amount you open the valve.
5.4. The SDA01 may either be used as a handheld device or used in conjunction with SDAST Double Stand (fig.4) enabling the user to leave
the dryer in place.
5.5. When finished, turn off, disconnect from the air supply and store in a dry location.
fig. 3
fig. 4
.
ENvIRONMENT PROTEcTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7aR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
SDA01 | Issue: 3 (H,3,F) 30/08/18
Loading...