Sealey SAC2103B.V2,SAC2153B.V2,SAC2203B.V2 Instructions Manual
INSTRUCTIONS FOR:
COMPRESSORS BELT DRIVE 100LTR/3.0HP,
150LTR/3.0HP, 200LTR/3.0HP DIRECT DRIVE
MODEL No's: SAC2103B.V2, SAC2153B.V2, SAC2203B.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
SAC2103B.V2 Illustrated.
(others will differ slightly)
1 Direct compressed
air outlet.
2. Tank
3. Pressure reducer.
4. Belt guard.
5. Compressor unit.
6 Electric motor.
7. Pressure switch.
8. Pressure gauge.
9. Pivot wheel.
10. Condensate drain.
11. Wheel.
12. Check valve.
1. SAFETY INSTRUCTIONS
1.1. ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to
read, understand and comply with the following: You must check all
electrical products, before use, to ensure that they are safe. You must
inspect power cables, plugs, sockets and any other connectors for wear
or damage. You must ensure that the risk of electric shock is minimised
by the installation of appropriate safety devices. A Residual Current
Circuit Breaker (RCCB) should be incorporated in the main distribution
board. We also recommend that a Residual Current Device (RCD) is
used. It is particularly important to use an RCD with portable products
that are plugged into a supply which is not protected by an RCCB. If in
any doubt consult a qualified electrician. You may obtain a Residual
Current Device by contacting your Sealey dealer. You must also read
and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires that all portable
electrical appliances, if used on business premises, are tested
by a qualified electrician, using a Portable Appliance Tester
(PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of
electrical appliances responsible for the safe condition of those
appliances and the safety of the appliance operators. If in any
doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is
safe before connecting it to the power supply. See 1.1.1. and
1.1.2. and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit
and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or
damage and check all connections to ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance
matches the power supply to be used and that the plug is fitted
with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors.
Immediately have any faulty item repaired or replaced by a
qualified electrician.
1.1.10. Twin capacitors and a centrifugal switch aid trouble free starting
on a good 13amp supply. In some cases a 16amp supply may
be required and we recommend that a 16amp industrial
round pin plug should be fitted and connected to a 20amp
supply having a Type C breaker. If in doubt you must
contact a qualified electrician to ensure that a suitably rated
supply is available.
SAC2103B.V2
IMPORTANT! The use of extension leads to connect these
compressors to the mains is not recommended as the resulting
voltage drop reduces motor, and therefore pump performance.
1.2. GENERAL SAFETY INSTRUCTIONS
3 Familiarise yourself with the application and limitations of the
compressor.
3 Ensure the compressor is in good order and condition before
use. If in any doubt do not use the unit and contact an
electrician/service agent.
WARNING! Compressor must only be serviced by an
authorised agent. DO NOT tamper with, or attempt to adjust,
pressure switch or safety valve.
3 Before moving, or maintaining the compressor ensure it is
unplugged from the mains supply and that the air tank pressure
has been vented.
3 Maintain the compressor in good condition and replace any
damaged or worn parts. Use genuine parts only. Unauthorised
parts may be dangerous and will invalidate your warranty.
3 Read the instructions relating to any accessory to be used with
this compressor. Ensure the safe working pressure of any air
appliance used exceeds compressors output pressure. If using a
spray gun, check that the area selected for spraying is provided
with an air change system/ventilation.
3 Ensure the air supply valve is turned off before disconnecting
the air supply hose.
3 To move a transportable compressor use the handle only.
Lift the compressor so that the front leg gives enough clearance
for manoeuvring but maintain unit’s centre of gravity in front of
the wheels. DO NOT attempt to lift or move the compressor by
any other means.
3 Use the compressor in a well ventilated area and ensure it is
placed on a firm surface.
3 Keep tools and other items away from the compressor when
it is in use, and keep area clean and clear of unnecessary items.
3 Ensure the air hose is not tangled, twisted or pinched.
3 Keep children and unauthorised persons away from the working
area.
3 Only move the compressor by the handle if portable.
7 DO NOT dis-assemble compressor for any reason. The unit
must be checked by qualified personnel only.
7 DO NOT use the compressor outdoors, or in damp, or wet,
locations.
© Jack Sealey Limited
Original Language Version
SAC2103B.V2, SAC2153B.V2, SAC2203B.V2 Issue: 1 - 30/10/13
7 DO NOT operate within the vicinity of flammable liquids,
gases or solids.
7 DO NOT touch compressor cylinder, cylinder head or pipe
from head to tank as these may be hot.
7 DO NOT use this product to perform a task for which it has
not been designed.
7 DO NOT deface the certification plate attached to the
compressor tank.
7 DO NOT cover the compressor or restrict air flow around the
unit whilst operating.
q DANGER! DO NOT direct the output jet of air towards
people or animals.
7 DO NOT operate the compressor without an air filter.
7 DO NOT allow anyone to operate the compressor unless
they have received full instructions.
WARNING! The air tank is a pressure vessel and the
following safety measures apply:
7 DO NOT tamper with the safety valve, DO NOT modify or alter
the tank in any way and DO NOT strap anything to the tank.
7 DO NOT subject the tank to impact, vibration or to heat and
DO NOT allow contact with abrasives or corrosives.
3 Drain condensation from tank daily and inspect inside walls
for corrosion every three months and have a detailed tank
inspection carried out annually. The tank shell must not fall
below the certified thickness at any point.
WARNING! If an electrical fuse blows, ensure it is replaced
with an identical fuse type and rating.
3 When not in use, store the compressor carefully in a safe,
dry, childproof location.
3
When the compressor is not in use, it should be
switched off, disconnected from the mains supply and
the air drained from the tank.
2. INTRODUCTION & SPECIFICATIONS
Our top of the range single phase compressors, these units are suitable for the professional workshop and are fitted with a genuine 3hp
motor. Twin capacitors and a centrifugal switch aid trouble free starting on a good 13amp supply. In some cases a 16amp supply may be
required. Pumps feature heavy-duty full cast cylinders capped by alloy heads for improved heat dissipation and long life. Heavy-duty drive
guards protect belt and flywheel that is designed to force air over the pump to aid cooling.
Model: .......................SAC2103B.V2............ SAC2153B.V2 ............ SAC2203B.V2
Motor Output (HP):.........................3.......................3 .......................3
Voltage (V)/Phase: ..................... 230/1....................230/1 ....................230/1
Input current (A): .........................16......................16 ......................16
Speed (rpm): ..........................1280....................1280 ....................1280
Air Displacement (cfm/Lm): ............. 15/425...................15/425 ...................15/425
Max Free Air Delivery (cfm/Lm):.........10.9/309................. 10.9/309 .................10.9/309
Max Pressure (psi/bar): ................ 145/10...................145/10 ...................145/10
Tank Capacity (L): .......................100.....................150 ..................... 200
Dimensions (WxDxH) (mm):.......1040x460x910............ 1320x400x855 ............ 1440x440x900
Weight (kg): .............................66...................... 85 ...................... 97
Noise db(A): .............................76...................... 76 ......................76
Noise LwA db(A): . . . . . . . . . . . . . . . . . . . . . . . . . 96......................96 ......................96
3. PREPARATION
3.1. Remove compressor from packaging and inspect for any
shortages or damage. If anything is found to be missing or
damaged contact your supplier.
3.2. Save the packing material for future transportation of the
compressor. We recommend that you store the packing in a
safe location, at least for the period of the guarantee. Then, if
necessary, it will be easier to send the compressor to the
service centre.
3.3. Assemble the two xed wheels and the castor wheel to the
SAC2103B.V2 as shown in g.1.
3.4. Confirm that the mains voltage corresponds with the voltage
shown on the compressor data plate.
3.5. Position the compressor on a at surface or with a maximum
permissible inclination of 10° (g.2). Site in a well ventilated
place, protected against atmospheric polution and not in a
place subject to explosion hazard. If the surface is inclined and
smooth, check if the compressor moves while in operation – if
it does, secure the wheels with two wedges. If the surface is in
a raised position, make sure it cannot fall, securing it in a
suitable way.
fig.2
fig.1
SAC2103B.V2
fig.3
© Jack Sealey Limited
Original Language Version
SAC2103B.V2, SAC2153B.V2, SAC2203B.V2 Issue: 1 - 30/10/13
Loading...