Sealey SAC03224,SAC03250,SAC03290 Instructions Manual

INSTRUCTIONS FOR:

COMPRESSOR BELT DRIVE 1.5 HP
OIL FREE 24ltr, 50ltr, 90ltr

MODEL No's: SAC03224,SAC03250,SAC03290

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.

1. SAFETY INSTRUCTIONS

1.1. ELECTRICAL SAFETY

 WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any
other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety
devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a
Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply
which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting
your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.

1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.

1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to
the power supply. See 1.1.1 and 1.1.2 and use a Portable Appliance Tester.

1.1.4. Ensure that cables are always protected against short circuit and overload.

1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none are loose.

1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.

1.1.7. DO NOT pull or carry the appliance by the power cable.

1.1.8. DO NOT pull the plug from the socket by the cable.

1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Have any faulty item repaired
or replaced immediately by a qualified electrician. When an ASTA/BS approved UK 3 pin
plug is damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.

To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.

1.1.10. Products which require more than 13Amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.

1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable. If extension reel is to be used outdoors, ensure it is marked for outdoor use.

1.2. GENERAL SAFETY INSTRUCTIONS

 WARNING! This compressor must only be serviced by an authorised agent.
  Familiarise yourself with the application and limitations of the compressor.
  Ensure the compressor is in good order and condition before use. If in any doubt do not use the unit and contact an electrician/service

agent.

  Before moving, or maintaining the compressor ensure it is unplugged from the mains supply and that the air tool is disconnected.
  Use the compressor in a well ventilated area and ensure it is placed on a firm surface.
  Keep tools and other items away from the compressor when it is in use, and keep area clean and clear of unnecessary items.
  Keep children and unauthorised persons away from the working area.
 DANGER! DO NOT direct the output jet of air towards people or animals.
 WARNING! If an electrical fuse blows, ensure it is replaced with an identical fuse type and rating.
  DO NOT dis-assemble compressor for any reason. This unit must only be checked and serviced by an approved service agent.
  DO NOT use the compressor outdoors or in damp or wet locations.
  DO NOT operate within the vicinity of flammable liquids, gases or solids.
  DO NOT touch compressor cylinder head as it may be hot and will remain so for some time after shutdown.
  DO NOT use this compressor to perform a task for which it has not been designed.
  DO NOT leave the compressor running unattended.
  DO NOT operate the compressor whilst under the influence of drugs, alcohol or other intoxicating medication.
  DO NOT cover the compressor or restrict air flow around the machine whilst operating.
  DO NOT allow anyone to operate the compressor unless they have received full instructions.
  When not in use, store the compressor carefully in a safe, dry, dust free, childproof location.
 When the compressor is not in use, it should be switched off, disconnected from the mains supply and the air drained from

the tank.

© Jack Sealey Limited

Original Language Version

Original Language Version

FUSE RATING: 13AMP

SAC03224,SAC03250,SAC03290 ISSUE:3(SP) 11/11/13

NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible
for their safety. Children should be supervised to ensure that they do not play with the appliance.

2. INTRODUCTION & SPECIFICATION

Aluminium

app lications . Oil free, single piston pump is belt driven by a 1.5hp motor and xed to a vertical type tank, saving space around the workshop.

Precision welded receiver tank manufactured to meet Pressure Vessel Directive 2009/105/EC. Fitted with fully automatic pressure cut-out switch
and air regulator with gauge. Supplied with handle and wheels (SAC03050 & SA03290) for easy manoeuvrability. Fitted with ASTA/BS approved
non-rewirable plug.

cylinder with cast iron lining gives reduced weight and improved resistance to wear. Suitable for general purpose workshop

Model No: .................................SAC03224 .............SAC03250 ....................SAC03290

Motor Output: ..............................1.5hp .................1.5hp ............................1.5hp

Voltage/Phase ..............................230V - 1ph .............230V - 1ph .....................230V-1ph

Rated Supply: ..............................13A...................13A............................... 13A

Air Displacement cfm(ltr/min): ..................5.6(158) ...............5.6(158) ........................5.6(158)

Maxiimum Free Air Delivery cfm(ltr/min) . . . . . . . . . . 3.32(94) ...............3.32(94) ........................3.32(94)

Maximum Pressure: .........................116psi/8bar ............116psi/8bar...................116psi/bbar

Receiver Capacity: ..........................24ltr ..................50ltr ..............................90ltr

Dimensions (W x D x H) ......................415 x 415 x 500mm......430 x 455 x 710mm .....430 x 455 x 1035mm

Weight: ...................................15.8kg ................23.4kg ............................35kg

3. PREPARATION

3.1. Remove compressor from packaging and inspect for any shortages or damage. If anything is found to be missing or damaged, contact

your supplier.

3.2. If wheels and/or feet are not fitted to compressor, fit them using the appropriate nuts, bolts and washers supplied.

3.3. Confirm that the mains voltage corresponds with the voltage shown on the compressor data plate.

4. OPERATION

SAC03224

SAC03224

g.1

 WARNING! Ensure that you have read, understood and apply Section 1 safety instructions.

4.1. The compressor should be located and operated in a position that allows good air circulation around the unit. Locate the compressor

in a convenient position for the work to be undertaken. Ensure that it is standing on a stable and level surface. Ensure the feet/wheels
are in direct contact with the surface.

4.2. Attach the required air tool to the air outlet. (fig1.B)

4.3. Plug the mains plug into a mains electrical socket, but do not switch the compressor on until the workpiece and air tool are fully

prepared.

4.4. Switch on the unit by pulling the red On/Off switch outwards(fig 1.A).

4.5. The output pressure is regulated by the pressure regulator. (fig 1.C). Turn the regulator knob clockwise to increase pressure to

the required level and vice-versa.The setting can then be retained by tightening the red locking ring below the knob.
When the compressor is not being used, set the regulated pressure to zero so as to avoid damaging the regulator.

4.5.1. The right-hand pressure gauge (fig 1.E) indicates the pressure inside the main tank. The left-hand gauge (fig.1.D) indicates the
pressure supplied to the air equipment. The pressure switch stops the motor when the maximum tank pressure is reached and
restarts it when pressure falls below the minimum threshold - approximately 2bar (29psi) less than the maximum pressure.

SAC03250

SAC03290

SAC03250,SAC03290

g.2 g.3

g.1

© Jack Sealey Limited

Original Language Version

SAC03224,SAC03250,SAC03290 ISSUE:3(SP) 11/11/13