InStruCtIonS For:
AIR RATCHET WRENCH 1/4" & 3/8"
SQ DRIVE SUPER STUBBY
MoDEl no'S: SA632.V2 & SA633.V2
Thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PlEASE READ THESE INSTRUCTIONS CAREfUllY. NOTE THE SAfE OPERATIONAl REQUIREmENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTlY AND WITH CARE fOR THE PURPOSE fOR WHICH IT IS INTENDED. fAIlURE TO DO SO mAY CAUSE DAmAGE AND/OR
PERSONAl INJURY AND WIll INVAlIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAfE fOR fUTURE USE.
1. SAfETY
Follow all workshop safety rules, regulations, and conditions when using wrench.
WARNING!Disconnect from air supply before changing accessories or servicing.
Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Un-authorised parts may be
dangerous and will invalidate the warranty.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
secure.
Wear approved safety eye/face shield, ear defenders and hand protection.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and non essential persons away from the working area.
DO NOT use the wrench for a task it is not designed to perform.
WARNING! DO NOT use wrench if damaged or thought to be faulty. Contact Service Agent.
DO NOT use wrench unless you have been instructed in its use by a qualified person.
DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT carry wrench with your hand on power trigger, in order to avoid unintentional starting.
DO NOT direct air from the air hose at yourself or others.
When not in use disconnect from air supply and store in a safe, dry, childproof location.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
2. INTRODUCTION
ultra-compact air ratchet wrenches fit in the palm of the hand. Perfect for working around tightly-packed engine compartments. ratchet yoke
designed and manufactured to provide additional strength. rear exhaust with baffle to reduce noise.
ImPORTANT WARRANTY INfORmATION
This product is covered by a 1 year parts and labour warranty, except for the ratchet head. This does not affect your statutory rights. DO NOT
operate with external leverage, hence exceeding rated torque. DO NOT drop the tool after task completion, always place down to prevent
ratchet head damage.
3. SPECIfICATION
mODEl: .................SA632.V2 .............SA633.V2
Drive Size: ................. 1/4”Sq ............... 3/8”Sq
Max torque: ........... 34nm(25lb.ft) ..........34nm(25lb.ft)
Air Consumption: ............ 2.4cfm ............... 2.4cfm
operating Pressure:............90psi ................ 90psi
Air Inlet Size: .............. 1/4”BSP ..............1/4”BSP
length: . . . . . . . . . . . . . . . . . . . . 125mm ...............125mm
noise Power: ...........101.49dB(A) ...........101.49dB(A)
noise Pressure: ..........91.33dB(A) ............91.33dB(A)
Weight: ......................0.5kg ................ 0.5kg
4. ASSEmBlY
4.1. Air Supply. (recommended hook-up procedure is shown in fig.2.)
4.1.1. Ensure wrench air valve (or trigger) is in the "off" position before connecting to the air supply.
4.1.2. You will require an air pressure of 90psi, and an air flow according to specification.
4.1.3. WARNING! Ensure the air supply is clean and does not exceed 90 psi while operating the wrench. too high an air pressure and/or
unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.4. Drain the
4.1.5. Clean compressor air inlet filter weekly.
4.1.6. line pressure should be increased to compensate for unusually long air hoses (over 8 metres). the minimum hose diameter should be
1/4” I.D. and fittings must have the same inside dimensions.
4.1.7. Keep the hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
4.2. Couplings.
Vibration may cause failure if a quick change coupling is connected directly to the wrench. to overcome this, connect a leader hose to
the wrench. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. See fig.1 & fig.2.
fig.1
compressor air tank daily. Water in the air line will damage the wrench.
fig.2
© Jack Sealey limited
Original Language Version
SA632.V2,SA633.V2 Issue: 1 - 22/08/14
5. OPERATION
WARNING! Ensure you read, understand and apply safety instructions before use.
5.1. With seized or rusted nut use a penetrating oil and a spanner to "crack" the fixing.
5.2. Fit the required socket to the wrench.
5.3. Connect the wrench to the air hose as indicated in section 4.
5.4. Place the socket over the subject nut and depress the trigger to operate the wrench.
5.5. to change the wrench direction turn the switch on the head of the wrench (see fig.3). F = Clockwise, r = Anti-clockwise.
DO NOT use worn or damaged sockets.
DO NOT use any additional force upon the wrench in order to remove a nut; it is possible to damage the head by using excessive
hand force.
DO NOT
allow the wrench to free run for an extended period of time as this will reduce bearing life.
fig.3
Palm grip surface
twist to change direction
Blanking cap
oil
daily
1/4" SA632.V2
3/8" SA633.V2
6. mAINTENANCE
WARNING!Disconnect wrench from air supply before changing accessories, servicing or performing maintenance. replace or
repair damaged parts. Use genuine parts only.
Un-authorised parts may be dangerous and will invalidate the warranty.
6.1. If the air system does not have an oiler, lubricate the air wrench daily with a few drops of Sealey air tool oil dripped into the air inlet to
prolong its life.
6.2. Clean the wrench after use with a dry cloth.
6.3. loss of power or erratic action may be due to the following:
a) Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or type of hose connectors. to remedy check
the air supply and follow instructions in section 4.
b) Grit or gum deposits in the wrench may also reduce performance. If your model has an air strainer (located in the area of the air
inlet), remove the strainer and clean it. Flush the wrench out with gum solvent oil or an equal mixture of SAE no 10 oil and paraffin.
Allow to drain before use.
6.4. For a full service contact your local Sealey service agent.
6.5. When not in use, disconnect from the air supply, clean the wrench with a dry cloth and store in a safe, dry, childproof location.
© Jack Sealey limited
Original Language Version
SA632.V2,SA633.V2 Issue: 1 - 22/08/14
Loading...