INSTRUCTIONS FOR:
AIR HAMMER KIT COMPOSITE PREMIER
MEDIUM/LONG STROKE
MODEL NO’S: SA613.V2 & SA614.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to
these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
1. SAFETY INSTRUCTIONS
WARNING!
Ensure Health & Safety, local authority and general workshop practice regulations are
adhered to when using this equipment.
WARNING!Disconnect hammer from the air supply before changing accessories, servicing
or performing any maintenance.
Keep the hammer clean and maintain it in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
Keep the work area clean and uncluttered. Ensure that there is adequate lighting.
Ensure chisels are correctly rated for the job. DO NOT use damaged or suspect chisels.
WARNING! Wear approved safety eye or face protection, ear defenders and, if dust is
generated, respiratory protection.
Keep hands and body clear of the work when operating the hammer.
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip
shoes.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain
and/or tie back long hair.
Keep children and unauthorised persons away from the work area.
Secure unstable workpiece with a clamp, vice or other adequate holding device.
Avoid unintentional starting.
WARNING! Ensure that the correct air pressure is maintained and not exceeded.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before use and
ensure all connections are secure.
DO NOT use the hammer for a task it is not designed to perform.
DO NOT operate the hammer if any parts are damaged or missing as this may cause failure
and/or personal injury.
WARNING! DO NOT chisel into any materials containing asbestos.
WARNING! DO NOT chisel into any workpiece where there is a risk of a live electrical power
source.
DO NOT switch the hammer on whilst the chisel is in contact with the workpiece.
DO NOT carry the by the hose, or yank the hose from the air supply.
DO NOT hold the workpiece by hand. Use clamps or a vice (available from your Sealey
dealer) to secure the workpiece.
DO NOT allow untrained persons to operate the hammer.
DO NOT operate the hammer when you are tired or under the influence of alcohol, drugs or
intoxicating medication.
DO NOT
use hammer where there is flammable liquid, solid or gas such as paint solvent, including
waste wiping or cleaning rags etc.
DO NOT leave the hammer operating unattended.
DO NOT carry the hammer with your finger on the trigger.
DO NOT direct air from the air hose at yourself or others.
When work is complete, ensure that the air supply is turned off.
When not in use, disconnect from the air supply and store in a safe, dry, childproof area.
© Jack Sealey Limited
Original Language Version
SA613.V2, SA614.V2 Issue: 1 - 04/10/13
2. SPECIFICATIONS & INTRODUCTION
Composite lightweight housing reduces effects of chill on operator’s hands for added comfort.
Exhaust outlet adjusts 360° keeping airflow away from operator. Heat treated alloy steel impact
components ensures suitability for the professional workshop. Supplied in storage case with five
chisels.
Model No: .............SA613.V2 ....... SA614.V2
Chisel Shank Size: .401” Parker Taper .401” Parker Taper
Speed: .................4200bpm ........3000bpm
Stroke: ................... 50mm .......... 71mm
Air Consumption: ...........7.4cfm ..........7.8cfm
Operating Pressure:..........90psi ...........90psi
Air Inlet Size: ..............¼”BSP ..........¼”BSP
Weight: ...................1.36kg ..........1.56kg
Sound Power:............111dB(A) ........112dB(A)
Sound Pressure:..........100dB(A) ........101dB(A)
Vibration Figure:......... 13.21m/s2 ....... 14.04m/s
Uncertainty Value: .........1.8m/s2 ........ 1.88m/s
2
2
3. PREPARING TOOL FOR USE
3.1. Air Supply
WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the
hammer. Too high an air pressure and unclean air will shorten the product life due to
excessive wear, and may be dangerous causing damage and/or personal injury.
3.1.1. Ensure hammer air valve (or trigger) is in the "off" position before connecting to the air
supply.
3.1.2. An air pressure of 90psi is required, and an air flow according to specification.
3.1.3. Drain the air tank daily. Water in the air line will damage the hammer.
3.1.4. Clean air inlet filter weekly.
3.1.5. Line pressure should be increased to compensate for unusually long air hoses (over 8
metres). The minimum hose diameter should be 1/4” internal diameter and fittings must
have compatible dimensions.
3.1.6. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain
that all connections are secure.
3.2. Couplings
Vibration may cause failure if a quick change coupling is connected directly to the wrench.
To overcome this, connect a leader hose to the air hammer (Sealey ref: AH2R or AH2R/38).
A quick change coupling may then be used to connect the leader hose to the air line recoil
hose (see figs.1 & 2).
fig.1
© Jack Sealey Limited
Original Language Version
fig.2
SA613.V2, SA614.V2 Issue: 1 - 04/10/13
Loading...