iNStruCtiONS FOr:
Pin cLutcH air iMPact
WrencH 1/2” DriVe
MODEl NO: sa6001.V2
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLease reaD tHese instructions carefuLLy. note tHe safe oPerationaL reQuireMents,
WarninGs anD cautions. use tHis ProDuct correctLy anD WitH care for tHe PurPose for WHicH
it is intenDeD. faiLure to Do so May cause DaMaGe anD/or PersonaL inJury anD WiLL inVaLiDate
tHe Warranty. PLease KeeP instructions safe for future use.
1. safety instructions
Follow all workshop safety rules, regulations, and conditions when using wrench.
WarninG!Disconnect from air supply before changing accessories or servicing.
Maintain the wrench in good condition and replace any damaged or worn parts. Use
genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
WarninG! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
Only use impact sockets which are specifically designed for use with an impact wrench.
Wear approved safety eye/face shield, ear defenders and hand protection.
WarninG! Due to the possible presence of asbestos dust from brake linings, when working
around vehicle brake systems we recommend you wear suitable respiratory protection.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and non essential persons away from the working area.
Do not use the wrench for a task it is not designed to perform.
WarninG! Do not use wrench if damaged or thought to be faulty. Contact Service Agent.
Do not use wrench unless you have been instructed in its use by a qualified person.
Do not carry the wrench by the air hose, or yank the hose from the air supply.
Do not operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
Do not carry wrench with your hand on the power trigger in order to avoid unintentional starting.
Do not direct air from the air hose at yourself or others.
When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. introDuction & sPecification
Composite casing with soft grip makes the tool lighter, easier to handle and helps reduce vibration
and chill. Handle exhaust reduces noise level. New pin clutch design gives the wrench a high
torque output making it suitable for jobs that would normally require a 3/4” impact wrench. Dial
type power and direction control on rear of wrench. Suitable for heavy tyre shop use.
Working/Maximum torque:. . . . . . . 700/800lb.ft
ultimate torque: ...................950lb.ft
Free Speed.....................10000rpm
Air Consumption: .................. 5.4cfm
Operating Pressure:. . . . . . . . . . . . . . . . . 90psi
© Jack Sealey limited 2013
Original Language Version
Air inlet Size: ....................1/4“BSP
Weight: ...........................2.1kg
Noise Power: ..................111.6dB(A)
Noise Pressure: ................110.6dB(A)
SA6001.V2 issue: 4 (SP) - 22/08/13
3. PreParinG WrencH for use
WarninG! Ensure the air supply is clean and does not exceed
90 psi while operating the wrench. too high an air pressure and/or
unclean air will shorten the product life due to excessive wear, and
may be dangerous causing damage and/or personal injury.
3.1 air suPPLy
3.1.1 Ensure wrench air valve (or trigger) is in the "off" position before
connecting to the air supply.
3.1.2 You will require an air pressure of 90psi, and an air flow according to specification.
3.1.3 Drain the compressor air tank daily. Water in the air line will damage the wrench.
3.1.4 Clean compressor air inlet filter weekly. recommended hook-up procedure is shown in fig 1.
3.1.5 line pressure should be increased to compensate for unusually long air hoses (over 8
metres). the minimum hose diameter should be 1/4” i.D. and fittings must have the same
inside dimensions.
3.1.6 Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain
that all connections are secure.
3.2 couPLinGs
Vibration may cause failure if a quick change coupling is connected directly to the wrench.
to overcome this, connect a leader hose to the wrench. A quick change coupling may then
be used to connect the leader hose to the air line recoil hose. See fig 1 & 2.
fig 1
fig 2
4. oPeratinG instructions
WarninG! ensure you read, understand and apply safety instructions before use.
4.1 Only use impact sockets which are specifically designed for use with a impact wrench.
4.2 Connect the wrench to the air hose as in chapter 3.
4.3 Place the socket over the subject nut and depress the trigger to operate the wrench.
4.4 to change direction use the dial located on the rear, this also controls the power of the
wrench.
Do not use any additional force upon the wrench in order to remove a nut.
Do not allow wrench to free run for an extended period of time as this will reduce bearing
life.
© Jack Sealey limited 2013
Original Language Version
SA6001.V2 issue: 4 (SP) - 22/08/13
Loading...