instructions for
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
transportacar trolley
model no: re901
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
refer to
instructions
Wear safety
footwear
1. safety
9 ensure the trolley is in sound condition and good working order. take action for immediate repair or replacement of damaged parts.
use genuine parts only. the use of improper parts may be dangerous and will invalidate the warranty.
WarnInG! Prepare the vehicle ready for resting and moving on the trolley. ensure the vehicle will not move, tip, fall etc
once it has been seated on the trolley. take any necessary precautions to protect persons, property and equipment when using this
trolley.
9 locate the trolley in a suitable, well lit working area.
9 Keep working area clean and tidy and free from unrelated materials.
9 use trolley on level and solid ground, preferably concrete. Avoid
tarmacadam as trolley may sink in.
9 ensure the vehicle engine is switched off .
9
ensure there are no passengers in the vehicle.
9 ensure all non-essential persons keep a safe distance whilst the
9 trolley is in use.
9 only place trolley under those lifting points recommended by vehicle
manufacturer (see vehicle hand book).
9 check the lifting point is stable and correctly held in trolley supports.
9 ensure the trolley wheels are free to move and that there are no
obstructions.
9 ensure you have a clear view and necessary assistance when
transporting vehicle.
9 ensure there are no persons or obstructions beneath the vehicle before moving.
9 When stationary, always lock the two brake wheels.
8 Do not operate the trolley if damaged.
8 Do not allow untrained persons to operate the trolley.
8 Do not exceed the rated capacity of the trolley.
WarnInG! Do not use the trolley to hold and move a vehicle which is unstable.
8 Do not allow the vehicle to move on the trolley.
8 Do not move vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
8 Do not work under the vehicle unless supported by axle stands which have been correctly positioned.
8 Do not ride on the trolley.
8 Do not use the trolley without appropriate supports.
8 Do not use the trolley for purposes other than which it is intended.
9 When not in use store trolley in a safe, dry, childproof area.
g.1
2. IntroDuctIon
Heavy duty steel frame-work suitable for supporting partly dismantled or badly damaged vehicles. enables easy movement around body shop.
supports interchangeable between v-crutches and sill clamps. supports and clamps adjustable for height and overall width. the trolley is fitted with
2 brake locking wheels.
3. specIfIcatIons
Model no: ...................................................................re901
capacity: .................................................................... 2000kg
min. height: ................................................................250mm
max. height: ...............................................................310mm
min. width: ................................................................1035mm
max. width: ...............................................................1430mm
length: .......................................................................600mm
(widths measured between the centre of the trolley points)
© Jack sealey limited
Original Language Version
re901 | issue 3(i) 10/04/17
4. asseMbly
4.1. Assemble four wheels with nuts, spring washer, washers, and bolts. ensure that the
two locking wheels are at the same end.
4.2. remove extension arm (fig1.c) from main beam undoing knob (A) and lifting arm off.
4.3. Assemble main beam (c) to wheel frames by fixing with four bolts, spring washers,
washers and nuts at each end (B).
4.4. check that all connections are tight and replace the extension arm (c) by screwing
knob (A) into the holding plate set inside the frame of the main beam.
4.5. screw the appropriate supports into the end of the extension arm at point (X) and place
the unused supports in their storage eyes (d).
WarnInG! Before use ensure section 1 safety instructions are read and understood.
4.6. check and prepare the vehicle as mentioned in the safety instructions ensuring the ground
on which the trolley is to
4.7. Position the trolley supports under the vehicle manufacturer’s recommended lifting point. if using the sill clamps ensure
they are correctly fitted and tightened. check that the vehicle is secure and there are no persons or obstacles beneath
the vehicle or in the path of transportation. ensure the wheel brakes are unlocked and move the vehicle.
4.8. When the trolley destination is reached, the trolley wheel brakes must be applied to stop further movement.
Do not use trolley as a support stand for working on, or under, the vehicle. the trolley is designed for manoeuvring only.
travel is level and solid (not tarmacadam).
g.2
5. MaIntenance
5.1. Before each use check for broken, cracked, bent, or loose parts, or any visible damage. if any suspect item is found remove trolley
from service and take necessary action to remedy the problem.
Do not use the trolley if believed to have been subjected to abnormal load or shock load.
5.2. Keep the trolley clean and periodically oil the wheel bearings.
6. parts DIaGraMpart
7.
Item part no Description
1 re901/01 screW m6x10
2 re901/02 PressinG BoArd
3 re901/03 dePression BAr
4 re901/04 PressinG BoArd
5 re901/05 Bolt m12x35
6 re901/06 WAsHer
7 re901/07 sPrinG
8 re901/08 nut m12
9 re901/09 BeArinG Post
10 re901/10 Bolt m12x70
11 re901/11 WAsHer
12 re901/12 Bolt m10x25
13 re901/13 GriP
14 re901/14 sPrinG Pin
15 re901/15 screW
16 re901/16 locA tinG AdAPtor
17 re901/17 BlocK
18 re901/18 moVABle BeAm
19 re901/19 crossBeAm
20 re901/20 suPPort BeAm
21 re901/21 sPrinG WAsHer
22 re901/22 nut m10
23 re901/23 Bolt m8x20
24 re901/24 WAsHer
25 re901/25 nut m8
26 re901/26 cAstor AssemBl Y
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
IMportant: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
recycle unwanted materials instead of disposing of them as waste. all tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
Original Language Version
environmental protection
01284 757500
01284 703534
www.sealey.co.uk
sales@sealey.co.uk
re901 | issue 3(i) 10/04/17
Loading...