Sealey PW2200,PW2500 Instructions Manual
INSTRUCTIONS FOR
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
PRESSURE WASHER 140/170BAR
WITH TSS & ROTORBLAST NOZZLE 230V
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
Refer to
instruction
manual
Wear eye
protection
Wear ear
protection
Wear safety
footwear
Wear protective
clothing
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the pressure washer is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is tted with the correct
fuse - see fuse rating in these instructions.
8 DO NOT pull or carry the appliance by the power cable.
8 DO NOT pull the plug from the socket by the cable.
8 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired
or replaced immediately by a qualied electrician.
1.1.3. This product is tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualied electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualied electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
MODEL NO: PW2200, PW2500
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualied electrician.
1.2. GENERAL SAFETY
WARNING! Water and electricity are dangerous partners. Be extremely cautious and ALWAYS be aware that this device uses an
electric motor. Always plug into a RCD (See electrical safety above). Unplug from mains before changing accessories or servicing.
WARNING! DO NOT use the washer if any part of the unit, gun, nozzle, detergent tank, hose or cables is damaged. Replace or
repair using genuine parts only. Unauthorised parts may be dangerous and will invalidate your warranty. Always check connections
are correctly secured and not cracked or damaged in any way before using the machine.
WARNING! Use washer on a at, levelled surface, in an upright position. Failure to do so will invalidate your warranty.
NEVER lay the washer down during use.
9 Ensure you comply with all local water supply regulations. Power washers may only be connected to mains water supply if a
check valve is installed in the supply hose, or at the tap outlet.
9 The supply hose must be reinforced, and have an internal diameter of 1/2”. The water supply must be at least equal to the
cleaner capacity. The water temperature must NOT exceed 122°F (50°C). The water supply pressure must NOT exceed 6 bar (90psi).
9 Always be aware of the hazards that may occur during use. Study all applications and limitations of the washer before use.
9 Use where air can freely circulate around the washer to avoid the machine overheating.
9 Keep the washer in good condition. Use an authorised service agent to service the unit.
9 Wear adequate protective clothing, goggles and anti-slip rubber soled footwear.
9 Position the washer as near to the water supply as possible.
WARNING! Ensure all persons and animals keep at a minimum distance of 15mtr from the washer when in use.
WARNING! The pressure washer must only be used with clean water. Unltered water or corrosive chemicals must not be used as
these will damage the cleaner.
9 Ensure the nozzle is aimed correctly at the work surface before switching on the machine.
9 Before activating the trigger, grip the gun rmly to counteract the recoil from the high pressure water jet.
WARNING! Avoid sudden bursts of water as these will cause water pressure to drop and put extreme pressure on hoses and
connectors.
9 If, during operation, power failure occurs turn the electricity and water off for safety reasons.
© Jack Sealey Limited
Original Language Version
PW2200, PW2500 | Issue:4(L) 10/10/17
Recommended fuse rating
13 Amp
WARNING! The high pressure jet will cause loose particles to be propelled at high speed, which may cause serious injury.
WARNING! DO NOT operate the machine without a water supply. Dry running can seriously damage the unit.
WARNING! DO NOT leave the washer switched on for more than 15 minutes without operating the trigger.
8 DO NOT obstruct ventilation grilles during operation.
8 DO NOT use the washer with ammable or toxic liquids or any other product. Use only recommended detergent. Unapproved
detergents may corrode the machine cover and accessories.
8 DO NOT jam the trigger in the operating position.
8 DO NOT adjust any internal control valves, as they have been factory set.
8 DO NOT connect other appliances to the machine inlet or outlet.
8 DO NOT use hoses and ttings other than those designed for use with this machine.
8 DO NOT move the unit by pulling the hoses or electrical cables. Use the handle and transport by means of the wheels.
8 DO NOT touch plug with wet hands. To avoid the risk of electrocution keep all connections dry and off the ground.
8 DO NOT direct jet against yourself, other persons, animals, electrical equipment or the machine itself.
8 DO NOT use washer if you are tired or under the inuence of alcohol, drugs or intoxicating medication.
8 DO NOT allow children or untrained persons to operate the washer.
WARNING! Discharge residual pressure before disconnecting the washer hose. Pressure left in unit may cause injury.
9 After use, disconnect washer from electrical mains and water supply and store in a safe, dry, childproof area.
9 Protect from freezing conditions during winter.
NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or
lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
2. INTRODUCTION
Semi-professional, heavy-duty unit for extensive domestic and light commercial use. Fitted with powerful induction motor (for motor power and
pump performance see ‘specications’). Features automatic Total Stop System (TSS) which switches the motor on and off when the lance trigger
is operated, prolonging the motor life. Also tted with high quality polished chrome and brass ttings. Features hose hanging hook, accessory
storage on the back of the unit and side mounted gun and lance holder ensuring the unit stays clutter free and fully mobile. Supplied with
variable nozzle, 5mtr hose and Rotablast nozzle which helps develop the same Effective Cleaning Power (ECP) as a larger pressure washer (for
delivery pressure see ‘specications’). Fitted with heavy-duty composite wheels for transportation over rough terrain.
Model No. PW2200 features dual built-in dual detergent tanks, enabling the user to switch between two different cleaning products by simply
using the detergent selection control. E.g: General Purpose Detergent, Model No’s AK130 or AK131 and Trafc Film Remover, Model No’s
AK132 or AK133.
3. SPECIFICATION
Model No: ............................................................. PW2200
Maximum Pressure: ................................... 140bar/2030psi
Effective Cleaning Pressure (ECP) ............ 257bar/3727psi
Water Flow: ............................................................400ltr/hr
Motor Power: ............................................................1800W
Supply: ................................................................230V~13A
Total Stop System (TSS): .............................................. Yes
Rotablast Nozzle: .......................................................... Yes
Hose Length: ................................................................ 5mtr
Weight: ..................................................................... 17.2kg
Model No: ............................................................. PW2500
Maximum Pressure: ................................... 170bar/2350psi
Effective Cleaning Pressure (ECP) ............ 275bar/3995psi
Water Flow: ............................................................438ltr/hr
Motor Power: ............................................................2200W
Supply: ................................................................230V~13A
Total Stop System (TSS): .............................................. Yes
Rotablast Nozzle: .......................................................... Yes
Hose Length: ................................................................ 5mtr
Weight: ..................................................................... 19.7kg
PW2200
PW2500
4. SET UP
4.1. CONNECTING THE WATER SUPPLY
4.1.1. Use a reinforced hose pipe with an internal diameter of 1/2” and connect to the mains water supply. Before attaching the hose to the
pressure washer flush the hose through with some clean water to remove any foreign matter from within the hose.
4.1.2. Connect female quick connection hose fitting to inlet on the front of the machine (fig.1)
4.2. CONNECTING THE HIGH PRESSURE HOSE (PW2200 ONLY)
4.2.1. Insert the high pressure hose into the hose fitting at the lower rear of the machine and screw the collar onto the threaded outer (fig.2)
ensuring the connector is tight. The PW2500 is pre-connected via the inside of the hose storage reel.
4.2.2. Attach the other end of the high pressure hose to the gun (fig.3). To attach the hose, push the male hose connector into the underside
of the gun and screw the collar onto the gun fitting. Ensure that the connection is tight to prevent leakage.
4.3. ASSEMBLING THE LANCE AND NOZZLE
4.3.1. Push the nozzle into the gun as shown in fig.4 and screw the threaded male lance connector into the gun, again ensuring that the
connection is tight.
WARNING! Ensure the nozzle is locked into position, failure to ensure this could result in the nozzle being ejected under high pressure
when operating the gun.
4.4. CONNECTING TO THE MAINS ELECTRICAL SUPPLY
WARNING! Ensure the On/Off switch is in the ‘Off’ position.
4.4.1. Using an RCD plugged into a 13A mains socket, DO NOT turn the power on. DO NOT touch the plug with wet hands.
© Jack Sealey Limited
Original Language Version
PW2200, PW2500 | Issue:4(L) 10/10/17
Loading...