Sealey PSI300,PSI800,PSI600,PSI1000 Instructions Manual
INSTRUCTIONS FOR: POWER INVERTER
MODEL No’s:
PSI800,PSI1000
Thank you for purchasing a Sealey product. Manufactured
to a high standard thi sproduct will, if used according to these instructions and properly maintained, give you years of trouble free
performance.
IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO
SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
1. SAFETY INSTRUCTIONS
DANGER! - Beware, lead-acid batteries generate explosive gases during normal battery operation.
Wash immediately with soap and water if battery acid contacts skin or clothing. If acid enters eye, flush immediately with cool
clean running water for at least 15 minutes and seek immediate medical attention.
DO NOT smoke or allow a spark or flame in the vicinity of the battery or engine.
If the battery terminals are corroded or dirty, clean them before attaching the leads.
WARNING! To prevent the risk of sparking, short circuit and possible explosion DO NOT drop metal tools in the battery area,
or allow them to touch the battery terminals.
Before attaching to battery, remove personal metallic items such as rings, bracelets, necklaces and watches. A lead acid
battery can produce a short-circuit current which is high enough to weld such items to the vehicle and cause severe burns.
Keep children and unauthorised persons away from the working area.
WARNING! DO NOT use on any vehicles other than those with 12Volt DC systems.
WARNING! For delicate items such as laptops, an anti-surge device is recommended.
DO NOT connect to any AC power source.
DO NOT disassemble. The inverter must be checked by qualified service personnel only.
DO NOT get inverter wet or use in damp or wet locations or areas where there is condensation.
DO NOT use the inverter for any purpose other than for which it is designed.
DO NOT pull the cables or clips from the battery terminals.
DO NOT operate the inverter if damaged.
DO NOT connect to a positive earthed system. Ensure you have the polarity correct before connecting, red clip to positive (+)
battery terminal and black clip to negative (-) battery terminal.
Before connecting ensure nothing is plugged into the inverter, and the inverter is switched OFF.
WARNING! Inverters become hot during use.
When not in use store inverter in a safe, dry, childproof location.
2. INTRODUCTION & SPECIFICATIONS
Pure sine wave inverter designed to produce the same AV frequency produced on the grid, making it more reliable
thantraditionalinverters,withoutanyuctuationinpowerorperformance.Operatesfroma12VDCpowersupply
found in cars, caravans, boats and HGV’s. High performance outlet eliminates electrical interference, reducing noise
levels during use. Suitable for powering small TV’s, laptops, power tools and various other electrical equipment within
the wattage rating of the inverter. Features USB port for use on various domestic equipment such as digital cameras
and mobile phones. Aluminium case provides durability and maximum heat dissipation. Safety features include
automatic overload shutdown and short circuit protection. Supplied with vehicle accessory plug and/or battery
terminal leads depending on model.
12V/230V PURE SINE WAVE
PSI300, PSI600,
MODEL NO: ...............................PSI300 .................... PSI600 ..................... PSI800 ......................PSI1000
Input Voltage: ............................12V DC ................... 12V DC .................... 12V DC .....................12V DC
Output Voltage: .........................230V AC ................. 230V AC ...................230V AC ...................230V AC
Continuous Output: ..................300W ...................... 600W ........................ 800W ........................ 1000W
Maximum Output: .....................600W ...................... 1200W ...................... 1600W ...................... 2000W
No Load Current Draw: ............<0.6A ...................... <0.8A ........................<0.8A ........................<1.0A
Fuse Rating: ..............................40A ......................... 35A x 2 .....................50A x 2 .....................30A x 4
Ambient Temperatue Range: ...0°C/40°C ................ 0°C/40°C .................0°C/40°C .................0°C/40°C
Dimensions (L x Wx H): ...........200 x 110 x 60mm .. 245 x 110 x 60mm ....285 x 140 x 75mm ....315 x 140 x 80mm
Supply Connection: ..................Vehicle accessory ... Battery terminal ........Battery terminal ........ Battery terminal
plug & battery leads. leads. leads.
terminal leads.
© Jack Sealey Ltd
Original Language Version
PSI300, PSI600, PSI800, PSI1000 Issue:1 -
06/12/12
g.1
g.3
PSI300
PSI600 PSI800
PSI1000
g.2
3. SETUP & OPERATION
3.1 Power Source Requirements.
3.1.1 . The inverter must be connected to a 12V DC negative earth system. DO NOT use with a positive earth system.
3.1.2 . The power source must be capable of providing between 10.5V and 15.0V and able to supply the necessary current
to operate the load.
3.2. Connecting Battery Leads to Inverter.
Check the battery is 12VDC. DO NOT use with a 6V or 24V battery.
Ensure that inverter is switched OFF and no flammable fumes are present before connecting to battery.
3.3. PSI300
3.3.1. Select either vehicle accessory plug lead or battery terminal lead.
3.3.2. To attach the battery leads remove the terminal caps from the rear of the inverter (Fig.2).
Place the black lead eyelet connector over the black (-) terminal post on the inverter, replace and tighten the
terminal cap.
3.3.3 . Place the red lead eyelet connector over the red (+) terminal post on the inverter, replace and tighten the terminal
cap.
3.3.4 . If using vehicle accessory plug lead, plug into vehicle accessory socket. (Some vehicle accessory sockets are not
permanently live; if the inverter does not operate immediately, try turning the ignition key to the first position).
3.3.5 . If using battery terminal lead, ensure battery terminals are clean; if necessary clean away any corrosion.
Connect red (+) clip then black (-) clip to red (+) and black (-) terminals of battery.
3.4. PSI600
3.4.1. Attach leads to inverter as in 3.3.2. and 3.3.3. above.
3.4.2. Connect as in 3.3.5. above.
3.5. PSI800, PSI1000
3.5.1. Attach leads to inverter as in 3.3.2. and 3.3.3. above.
3.5.2. Undo the securing bolt for the red (+) battery terminal and secure the red battery lead to the red (+) terminal post on the
battery.
3.5.3. Undo the securing bolt for the black (-) battery terminal and secure the black battery lead to the black (-) terminal post on
the battery.
3.5.4. Check all connections are secure.
3.6. Connection to Load.
Most electrical appliances, tools etc, have a rating plate indicating the power consumption in Amps or Watts. Use
these ratings to ensure you remain under the inverters continuous capacity. If the rating is shown in amps,
multiply the value by the voltage (230V) to determine the wattage.
3.6.1. Ensure that the inverter is switched OFF. Plug the equipment you wish to use into the inverter’s 3 pin socket or into the
USB port as required.
3.6.2. Make sure the load does not exceed the wattage rating of the inverter.
3.6.3. Switch the inverter on, check that everything is working and the green LED is lit (fig 3).
WARNING! DO NOT connect the inverter to any AC distribution wiring or any AC load circuit in which the neutral conductor
is connected to ground (earth) or to the negative of the DC (battery) source.
3.7. Placement of Inverter.
3.7.1. For best and safest operation the inverter should be placed on a flat and stable surface.
3.7.2 . Use only in a dry location, do not allow inverter to get wet.
3.7.3 . Use in cool ambient temperature of between 0°C and 40°C. Do not place on or near a heating vent.
3.7.4 . Allow sufficient space around the inverter for cooling. If the inverter overheats it will shut down and will not restart until it
has cooled down.
3.7.5 . DO NOT use near flammable materials or anywhere that flammable gasses could accumulate.
3.7.6 . The inverter may become uncomfortably hot during extended periods of full power use.
WARNING!DO NOT place on or near materials that may be affected by heat.
© Jack Sealey Ltd
Original Language Version
PSI300, PSI600, PSI800, PSI1000 Issue:1 -
06/12/12
Loading...