instructions for
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
micro air compressor with worklight
12V
model no: ms163
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
refer to
instructions
1. safety
9 familiarise yourself with the application, limitations and potential hazards of the compressor.
warNiNg! disconnect the compressor from the battery before changing accessories, servicing or performing any maintenance.
9 this appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
9 use only the supplied adaptors.
9 maintain the compressor in good condition, Do Not use if damaged.
9 ensure that there are no flammable or combustible materials (including gases) near the compressor when in use.
WArninG! this compressor is capable of high pressure. do not exceed the maximum safe pressure of the item being inflated.
WArninG! the gauge on the compressor is for guidance only. Where pressure is critical (e.g. tyres) check with a gauge of known
accuracy.
8 Do Not leave compressor operating unattended.
8 Do Not operate in wet or damp conditions.
warNiNg! to prevent overheating and subsequent damage to the unit, switch off after 15 minutes continuous operation and allow to cool
for 15 minutes before switching back on.
9 After use store in a safe, dry, childproof area with the connector locking lever in the unlocked position.
2. iNtroDuctioN
compact design incorporating integrl storage for air output hose. features a work light and pressure guage which reads up to 5.5bar/80psi.
Powered by a 12V motor suitable for inating tyres on motorcycles and cars. supplied with vehicle accessory socket plug and battery clips.
3. specificatioN
model no .....................................................................ms163
Hose length ...............................................................100mm
Power cord length ......................................................2.8mtr
operating Voltage ............................................................12V
4. operatioN
4.1. preparation for use:
note: Your ignition may need to be set to position ‘i’ (on) for the 12V output from the 12V accessory socket to function. furthermore, it is
recommended that your car engine is running when using this product so that your battery is not depleted and full power is supplied to the
unit. (Always check that the car is in neutral and the handbrake is on). this compressor is designed for use with a car 12V or motorcycle dc
power supply; do not connect to any other type of electrical power.
4.2. power connection:
connect either the vehical ‘accessory plug or the ‘battery clips’ to the ‘power lead’. for car use, plug in the ‘car accessory plug’ into the cars
accessory socket. for bike use, connect the ‘battery clips’ onto the terminal of the battery. red to + and Black to –.
Note: When connected the led light will be lit.
4.3. using the compressor:
Attach the air line securely to the valve on the tyre or any other item to be inated (use adaptors if necessary screw the adaptors into the Air
Line. Inating adapters for air rubber rings/air beds/footballs, etc.)
Press the ‘switch’ on and the compressor will start.
The compressor will inate the tyre (or other item).
Periodically stop the compressor to allow the gauge to steady so that it can be read.
once the correct pressure is reached, switch off and disconnect the air line from the valve.
Note: it is recommended in the interests of your safety that you check your tyres with a Bs approved tyre gauge to ensure your tyres are at
the correct pressure. Always check your tyres when they are cold.
© Jack sealey limited
Original Language Version
ms163 | issue 1 30/09/16
5. troubleshootiNg
Problem Posible cause solution
compressor does not run. Poor connection between cigarette lighter
plug adaptor and lighter socket.
rotate plug in socketto improve contact.
clean out socket.
g.1
ignition required to be on to power socket.
socket fuse blown
compressor runs but does not inate Valve connector or adaptor leaking.
other leaks
compressor runs at reduced speed Voltage low
overheating
parts support is available for this product. to obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
environmental protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
weee regulations
dispose of this product at the end of its working life in compliance with the eu directive on
Waste electrical and electronic equipment (Weee). When the product is no longer required, it must be disposed
of in an environmentally protective way. contact your local solid waste authority for recycling information.
turn on ignition
check and replace fuse if necessary
remove and ret connector or adaptor.
check compressor, connector hose and item
being inated for leaks
check condition of vehicle battery/charging
system
switch off compressor immediately and leave
to cool for 30 min.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
importaNt: no liability is accepted for incorrect use of this product.
warraNty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
Original Language Version
01284 757500
01284 703534
www.sealey.co.uk
sales@sealey.co.uk
ms163 | issue 1 30/09/16
Loading...