Sealey mes02 Instruction Booklet

instructions for

I

MPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

engine rebuild stand - multicylinder

model no: mes02

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.

refer to

instruction

manual

1. safety

 Warning! Ensure all Health and Safety, local authority , and general workshop practice regulations are strictly adhered to when using this

equipment.

8 dO nOt use unit if damaged.

9 replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9 Keep the stand clean for best and safest performance.
9 locate the stand in a suitable work area. Keep area clean and tidy and free from unrelated materials. ensure there is adequate lighting.
9 use on a firm, level surface capable of sustaining the stand and the load.
9 maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9 ensure all non-essential persons keep a safe distance whilst the stand is in use.
9 lock ratchet in position with locking pin before fixing a load and ensure the engine is centred and securely mounted.
9 ensure the stand and load are stable.

9 dO nOt allow untrained persons to use the stand.
8 dO nOt exceed the rated capacity of 75kg.
8 dO nOt use the stand for purposes other than those for which it is designed.

9 When not in use store stand in a safe, dry, childproof area.

2. intrOductiOn

suitable for a wide variety of engines and transmissions. features fully adjustable lower mounting arms and swivel castors, capable of supporting
larger (maximum 75kg) multi cylinder engines. supports can rotate for accessibility to all parts of the engine.

3. specificatiOn

model no: .................................................................. mes02

maximum capacity: ........................................................75kg

min./max. width engine mounting brackets: ........150-360mm

min./max. length: ................................................. 550/940mm

min./max. height: ................................................. 540/795mm

© Jack sealey limited

Original Language Version

mes02| issue 1 15/03/16

4. assembly

refer to g.1.

4.1. insert bottom frame (5) into bottom frame (2). secure with locking bolt (4).

4.2. Bolt upright posts (1) to either end of bottom frame assembly (5 & 2) using bolt (9), washer (7) and nut (6).

4.3. insert expansion posts (11 & 12) into upright posts (1), secure with pins (10) and r clips.

4.4. insert rotary frame 1 (23) into expansion post (11). Secure rst with circlip (25) and then bolt (13) washer (14) and nut (15).

4.5. insert rotary frame 2 (24) into expansion post (12). Secure rst with circlip (25) and then bolt (13) washer (14) and nut (15).

4.6. use ratchet (16) and locking bolt (4) on top of expansion post 2 (12) to adjust angle of rotary frames (24 & 25).

4.7. fit wheels (8) using washer (7) and nut (6).

4.8. slide supporting frames (21 & 22) onto rotary frames 1 & 2 (23 & 24), secure with bolts (20).

4.9. secure all fasteners.

5. OperatiOn

refer to gs. 2 & 3.

5.1. use original engine mounting bolts or studding, washers
and nuts of appropriate size to secure the engine to the stand
using supporting frames (21 & 22).

fig.1

y

fig.2

fig.3

parts support is available for this product. to obtain a parts listing and/or diagram,

please log on to www.sealey.co.uk, email [e-mail] or telephone [phone].

recycle unwanted materials instead of disposing of them as waste. all tools, accessories and packaging should be sorted,

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.

impOrtant: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

© Jack sealey limited

taken to a recycling centre and disposed of in a manner which is compatible with the environment.

When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)

into approved containers and dispose of the product and the fluids according to local regulations.

sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar

Original Language Version

environmental protection

01284 757500
01284 703534

www.sealey.co.uk

Web

[e-mail]

mes02| issue 1 15/03/16