Sealey LS575VH,LS575VH.v2 Instructions Manual

INSTRUCTIONS FOR:

HYDRAULIC LOG SPLITTER 8TONNE
575MM CAPACITY VERTICAL TYPE

MODEL: LS575VH

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY INSTRUCTIONS

1.1. SAFETY AND MAINTENANCE.

3 Keep the log splitter clean for best and safest performance.
3 Maintain the log splitter in a good condition (use an authorised service agent).
3 Use a qualified person to lubricate and maintain the log splitter.
7 DO NOT top up hydraulic unit using brake fluid. Use hydraulic jack oil only.
7 DO NOT operate the log splitter if damaged.
3 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

1.2. WORKSHOP/ENVIRONMENTAL SAFETY.

3 Locate the log splitter on dry, level and solid ground in a suitable work area with adequate lighting.
3 Keep the area clean and tidy and free from unrelated materials. Do not leave tools, logs or other items lying around where they could become a

tripping hazard.

7 DO NOT operate the log splitter in wet or damp areas or expose it to rain.
7 DO NOT operate the log splitter in areas where fumes from paint, solvents, or flammable liquids pose a potential hazard.

1.3. OPERATOR SAFETY.

3 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
3 Wear protective, electrically non conductive gloves .
3 Always wear safety goggles. Everyday spectacles are not sufficient protection.
3 Maintain correct balance and footing, do not over-reach. Ensure the floor is not slippery and wear non-slip, protective footwear.
7 DO NOT allow untrained persons to operate the log splitter.
7 DO NOT operate the log splitter with the guards or guides removed.
7 DO NOT operate the log splitter when you are tired or under the influence of alcohol, drugs or intoxicating medication.
3 The log splitter must always be operated by one person only.
3 Keep hands away from moving parts of the log splitter.
3 Keep hands away from splits and cracks which open in logs. They may close suddenly which could cause serious personal injury. For this

reason do not attempt to remove jammed logs by hand. A jammed log is a log which is only partially split and continues to grip the splitting
wedge.

1.4. SAFETY OF OTHERS.

7 DO NOT allow another person to help you with a jammed log.
3 Keep children and unauthorised persons away from the work area.
3 The log splitter must always be operated by one person only. Other people must

keep a safe distance from the log splitter especially when it is in operation.
3 Store the log splitter in a safe area away from children and other people not
qualified to use the log splitter.

1.5. GENERAL SAFETY.

7 DO NOT make any modifications to the log splitter.
7 DO NOT exceed the stated log capacity of the log splitter.
7 DO NOT use the log splitter for a task it is not designed to perform.
7 DO NOT force the log splitter to work beyond its specified capacity.
3 Ensure that there are no nails, screws or other foreign objects in logs to be split.
3 The ends of logs should be cut square and also if possible logs should be cut to

a uniform length.
p WARNING! The warnings, cautions and instructions referred to in this manual
cannot cover all possible conditions and situations that may occur. It must be
understood that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
3 When not in use, store the log splitter, with the hydraulic unit fully lowered, in a
safe, dry, childproof location.

2. INTRODUCTION & SPECIFICATION

Safe and easy way to split logs, offering continuous sizing and up to
8tonne of pressure. Seven tier wedge system allows workpiece to be as
near to wedge as possible so minimising splitting time. Operated by foot
pump requiring a maximum of 15 strokes to capacity (without load) for
easy and fast splitting.

Tier Log Lengths: ...................300, 350, 400, 450, 500, 550, 600mm

Maximum Log Diameter: .....................................160mm

Vertical Ram Travel:......................................... 158mm

Maximum Load Pressure: .....................................8tonne

Overall Size (W x D x H): .......................... 285 x 540 x 1040mm

Weight: ..................................................... 30kg

Original Language Version

LS575VH Issue: 1 - 24/11/09

3. ASSEMBLY & PREPARATION

3.1. Assembly.

3.1.1. Attach the hydraulic pump to the base by using two M8 allen
bolts (fig.1).

Fig.1

3.1.2. Slide the log support over the main post and down onto the
hydraulic pump unit (fig.1).

3.1.6. Attach foot pedal by inserting into the hydraulic pump socket.
Tighten bolt to secure the foot pedal in place (fig.4).

Fig.4

3.1.7. Attach the two springs into the centre holes of the feet.
Then attach the other ends of the springs to the log support.
(fig.5).

3.1.8. Attach the two log cradle arms to the splitter using four M6
bolts and four lock washers (fig.6).

Fig.5

Fig.2

3.1.3. Attach the two feet to the bottom of the main post, Secure
each foot using two M10 bolts, two lock washers Ø10 and
two M10 nuts. Bolt through the two outer holes (fig.2).

3.1.4. Slide the wedge assembly over the main post and locate
the pins into one of the sets of locating holes (fig.3).

3.1.5. Attach the two handles to the top of the log splitter, one
handle per side. Secure each handle using a lock washer Ø10
and a M10 nut (fig.3).

Fig.3

Fig.6

3.2. Transportation.

Carefully tip the log splitter backwards onto it's wheels, using
the handles to transport it short distances.

3.3. Work site preparation.
Plan the work site beforehand to ensure a safe working

environment and to save effort by positioning the logs so they
can easily be reached. Ensure that the log splitter is
positioned on firm and level ground. Locate site so that the
split wood can be stacked or loaded directly into a suitable
vehicle or trailer.
When cutting up wood for splitting, bear in mind the capacity
of the splitter, which is between 300mm and 600mm in 50mm
steps. Decide which length is most appropriate and cut the
wood slightly shorter than the set length.

Original Language Version

LS575VH Issue: 1 - 24/11/09