instructions for
I
MPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
lifting kit 2tonne 5pc
model no: Jkit01
thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
refer to
instructions
1. Safety
tRolley Jack
9 ensure the jack is in sound condition and good working order. take action for immediate repair or replacement of damaged parts.
use genuine parts only. the use of improper parts may be dangerous and will invalidate the warranty.
9 locate the jack in a suitable, well lit working area.
9 Keep working area clean and tidy and free from unrelated materials.
9 use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
9 Place chocks under wheels of vehicle (but ensure wheels of jack can freely move).
9 ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PA rK”
9 ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.
9 ensure there are no passengers in the vehicle.
9 ensure all non-essential persons keep a safe distance whilst the jack is in use.
9 only place jack under those lifting points recommended by vehicle manufacturer (see vehicle handbook).
9 check the lifting point is stable and centred on the jack saddle.
9 ensure the jack wheels are free to move and that there are no obstructions.
▲ DANGER! Use the jack for lifting only, NOT for supporting the lifted load.
9 use suitable capacity axle stands under the vehicle before proceeding with any task.
9 ensure there are no persons or obstructions beneath the vehicle before lowering.
9 use a qualified person to maintain or repair the jack hydraulic system.
8 Do not operate the jack if damaged.
8 Do not allow untrained persons to operate the jack.
8 Do not exceed the rated capacity of the jack (2 tonne). When lifting a load of maximum capacity or close to it, it is recommended that
the effort be reduced by the use of assistance during this operation.
8 Do not allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.
8 Do not jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
8 Do not work under the vehicle until axle stands have been correctly positioned.
8 Do not use the jack for purposes other than that for which it is intended.
8 Do not top up hydraulic system with brake fluid. use hydraulic jack oil only.
8 Do not adjust the safety overload valve.
9 When not in use store jack, fully lowered, in a safe, dry, childproof area.
aXle StanDS
WaRning!
Do not oveRloaD aXle StanDS beyonD RateD capacity. oveRloaDing can cauSe DaMage to, oR failuRe of,
the aXle StanDS. poSition loaD on centRe of cRutch/SaDDle only. alWayS uSe StanDS in paiRS on haRD
level SuRface capable of SuStaining the loaD. uSe of StanDS on otheR than haRD level SuRfaceS can
ReSult in loaD inStability anD poSSible loSS of loaD. Do not uSe on taRMacaDaM. failuRe to folloW
theSe inStRuctionS May ReSult in DaMage to aXle StanDS, loSS of loaD ReSulting in pRopeRty DaMage,
SeRiouS peRSonal inJuRy oR loSS of life.
▲ DangeR! gReat caRe MuSt be taken to enSuRe you loWeR the vehicle (oR otheR loaD)
SloWly anD caRefully onto the centReS of the cRutch/SaDDle of the aXle StanDS.
9 use only as specified by the manufacturer.
9 ensure the load does not exceed the maximum capacity as marked on the axle stand, per pair.
9 use no more than a single pair of stands either on the front, rear or one side of the vehicle. use in pairs.
9 no alterations or modifications shall be made to this product.
9 use on a hard, level surface, e.g. concrete. Do not use on uneven ground or tarmacadam.
9 securely chock wheels in contact with the ground. Before jacking and placing the stands, apply vehicle
handbrake (put automatics in ‘Park’).
9 make sure that each stand is securely located under a strong point on the vehicle; consult the vehicle manufacturer’s handbook for
guidance. ensure that height adjust locking mechanism is fully located before applying any load to the axle stand.
9 ensure that the load is located centrally on the saddle, and that the weight is directed through the vertical axis of the stand.
9 exercise extra care when using with a three wheeled vehicle or a trailer. refer to vehicle manufacturer’s instructions.
if automatic).
© Jack sealey limited
Original Language Version
JKit01| issue 4 27/09/16
9 once vehicle is supported, ensure that the vehicle and stands are stable before starting work. ensure that it is not possible for the vehicle
to move before commencing any work.
9 inspect stands before each use. Do not use if they show signs of damage. Do not use if it is suspected that they have been
overloaded.
9 Before commencing any work or going beneath the vehicle, undertake a risk assessment. ensure that a responsible person is aware of
the work about to be undertaken.
9 replace any labels on the axle stand should they become unreadable. this applies in particular to any warning or operation instruction
labels. if replacement labels are required, contact your sealey stockist.
8 Do not use axle stands on the highway, or anywhere else if it is deemed to be unsafe.
8 Do not push or twist the vehicle/load whilst it is supported on stands.
8 Do not mix components between stands. use only as supplied.
8 Do not allow children or animals in the vicinity of a vehicle supported on axle stands.
8 Do not leave a vehicle on axle stands in an area that could be considered a hazard to others or property.
9 folloW StepS 1, 2, anD 3 to coRRectly place vehicle / loaD onto aXle StanDS.
2. iintRoDuction
comprises essential equipment required to safely jack up a vehicle. includes a 2tonne trolley jack, a pair of folding wheel chocks, a pair of axle
stands (2tonne combined), 6 wheel padded creeper for comfort whilst carrying out maintenance and an extending l-bar wrench with 17mm & 19mm
socket.
3. iSpecification
Model no: .................................................................. Jkit01
Jack:
capacity: ................................................. 2 tonnes (2,000 kg)
minimum saddle height: .............................................140mm
maximum saddle height: ............................................340mm
maximum chassis height: ...........................................123mm
length: .......................................................................450mm
Weight: .......................................................................... 8.7kg
axle stands:
capacity each: ..........................................1 tonne (1,000 kg)
capacity pair: .......................................... 2 tonnes (2,000 kg)
minimum height: ......................................................... 291mm
maximum height: ........................................................ 391mm
creeper:
frame:............................................................................ steel
size l x W x d: ........................................901 x 425 x 120mm
Wheels: ................................................................................6
© Jack sealey limited
Original Language Version
JKit01| issue 4 27/09/16
Loading...