Sealey ht108led Instruction Booklet

RechaRgeable head toRch 5W cRee xpg

MPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

led auto sensoR

Model no: ht108led

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.

Refer to
Instructions

1. safety

1.1. general safety
9 ensure the lamp is fully charged before initial use.

8 do not turn the torch on when it is being charged.
8 do not shine directly into your, other person’s or animal’s eyes.
8 do not allow children to use the torch.
8 do not handle or move the torch whilst it is being charged.
8 do not use the torch if you suspect that the battery or the torch casing is damaged.

do not leave battery in a discharged state, recharge battery immediately. before storage, fully recharge the battery,
subsequently recharge the battery at least once every six months of non-use.

1.2. electrical safety

Use only the USB charging lead supplied to charge the battery.

 WaRnIng! It is the user’s responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCd
(Residual Current device) is used with all electrical products, particularly portable equipment which is plugged into an electrical
supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.

1.2.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualied

electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualied electrician.

1.2.3. You must ensure that you:

9 Inspect the cable and connector for wear and damage to ensure items are safe before connecting to the power supply.

8 do not use if worn or damaged.

1.3 battery safety

 WaRnIng! To reduce the risk of burns or re:

8 do not Attempt to open, disassemble, modify or service the battery pack.
8 do not Crush, puncture, short external contacts or dispose of in re or water.
8 do not expose to temperatures above 60°C (140°).

9 Replace only with the battery pack designated for this product.

9 Recycle or dispose of used battery as stipulated by local regulation.
If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool
water and seek immediate medical attention.

2. IntRoductIon

Hands-free head torch with adjustable 5W CRee XPG led spotlight to direct light as required. Features auto sensor to activate light with
the wave of a hand and standard on/off push button switch. Two output options of 100% and a 30% energy saving mode. Powered by a
rechargeable 3.7V 2Ah li-ion battery. Supplied with micro USB charging lead.

3. specIfIcatIon

Model no: ............................................................ ht108led

Battery: ..........................................................li-ion 3.7V-2Ah

lumen output 100%/30% .....................................360/100lm

operating Time 100% / 30% illumination .....................2hr/6hr

Charging Time: .................................................................6hr

© Jack Sealey limited

Original Language Version

HT108led Issue 2 (F) 11/02/19

Adjustable head band

Battery compartment
screw cap

on/Mode Change/off

Button

USB Cover

4. opeRatIon

4.1. Remove USB cover to reveal USB charging point, where the provided USB charging cable can be inserted g.1.

4.2. Plug in the cable to an appropriate power source. Charging will take approximately 6hr.

4.3. When charged remove USB cable and replace the USB cover.

4.4. To switch on press on/mode change/off button (100%), press again to change mode (30%), press again to switch off.

4.5. To activate by hand movement, hold down (approx 3 sec.) on/mode change/off button until button turns red. light can now be
operated by passing hand in front of sensor. Press button again to switch off.

5. MaIntenance

5.1. Keep the torch clean by wiping with a damp cloth.

5.2. Remove batteries if not being used for a long period of time.

5.3. Store torch and batteries in a dry childproof area.

Sensor

g.1

note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.

Important: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

envIRonMent pRotectIon

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.

Weee RegulatIons

dispose of this product at the end of its working life in compliance with the eU directive on Waste electrical and electronic equipment
(Weee). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.

batteRy ReMoval

Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme.
Jack Sealey ltd Batteries Producer Registration number (BPRn) is BPRn00705.

sealey group, Kempson Way, suffolk business park, bury st edmunds, suffolk. Ip32 7aR

01284 757500 01284 703534 [e-mail] www.sealey.co.uk

© Jack Sealey limited

Original Language Version

HT108led Issue 2 (F) 11/02/19