instructions for
MPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Galvanized steel floor cabinet 5 shelf
extra wide
model no: Gsc110385.v2
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
refer to
instructions
Wear protective
gloves
1. safety
GenerAl sAfetY
WArninG! ensure Health & safety, local authority, and general workshop practice regulations are adhered to when using this cabinet.
9 locate cabinet in a suitable work area.
9 Keep the work area clean, uncluttered and ensure there is adequate lighting.
warninG! use cabinet on level and solid ground, preferably concrete.
9 Keep the cabinet clean and tidy in accordance with good workshop practice.
9 Keep children and unauthorised persons away from the work area.
8 do not use the cabinet for any purpose other than that for which it is designed.
8 do not use the cabinet outdoors.
8 do not place the cabinet in a damp or wet location or an area where there is condensation.
8 do not clean the cabinet with any solvents which may damage the surfaces or the protective coating.
8 do not move the cabinet when there are items placed inside.
8 do not step on the shelves.
8 do not overload the cabinet.
2. introduction
floor standing galvanized steel cabinet with lockable double doors. Fitted with ve shelves, four of which are adjustable. Supplied with four
keys. ideal for factory, workshop or home use. features two rear wiring grommets allowing power tool batteries and other devices to be
charged whilst in storage. Floor cabinet is supplied at packed and will need some simple assembly.
3. specification
model no ....................................................... Gsc110385.V2
overall size (W x d x H) .....................1100 x 410 x 1830mm
shelf size ................................................1090 x 365 x 20mm
shelves ................................................................................5
4. asseMbly
4.1. Unpack the unit and conrm that all the parts listed.
4.2. Assemble the unit on a solid level surface.
4.3. the assistance of a second person will be required.
4.4. to assemble the unit you will require a rubber mallet and a Phillips-head screwdriver.
4.5. Where practical x unit to a wall for extra strength and durability.
© Jack sealey limited
Original Language Version
Gsc110385.V2 | issue 1 24/10/16
step 1
insert and slide front base bracket (e1) and back base
bracket (f1) into the bottom of left side panel (B1) and
right side panel (B2) as per diagram above. Attach
brackets using a self tapping screw (J) in each of
the four corners as shown in the diagram (g.1).
step 2
stand unit upright and install the left back panel (c1)
followed by the right back panel (c2). fix the back
panels with self tapping screws (J) as per the diagram
(g.2). At this stage, x all screws except those marked
with a cross. You will need an extra pair of hands to
assist from the opposite side while you x the screws.
g.1
g.2
g.3
step 3.
insert the middle column (G1) into the hole in the front base bracket (e1). fix it using a self tapping screw (J) from the back. install
the top panel (A1) and x it using self tapping screws (J) as per the diagram (g4). Install shelf supports (I) in the middle column
(G1) and in all four corners level for each designated height and then insert the shelves (d1).
© Jack sealey limited
Original Language Version
Gsc110385.V2 | issue 1 24/10/16
step 4.
install the right door (r1) and left door (l1) using the bottom hinge pins (K) and latches on the top. the space between the doors and
the top panel can be adjusted using washers (M) if necessary. Insert wiring grommets (N) into pre-cut holes in back panel.
g.4
environmental protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
iMportant: no liability is accepted for incorrect use of this product.
warranty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
Original Language Version
01284 757500
01284 703534
www.sealey.co.uk
sales@sealey.co.uk
Gsc110385.V2 | issue 1 24/10/16
Loading...