Sealey GSA674K Instructions For Use Manual

Refer to

Instructions

Wear Ear

Protection

Wear Eye
Protection

Wear a

Mask

Wear Protective

Gloves

INSTRUCTIONS FOR

AIR ANGLE GRINDER/

SANDER KIT 42PC

MODEL No: GSA674K

1. SAFETY

 Follow all workshop Health & Safety rules, regulations and conditions when using tool.

 WARNING! Disconnect from air supply before changing bit or servicing.

 Maintain grinder in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.

 WARNING! Check correct air pressure is maintained and not exceeded. We recommended 90psi.

Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all
connections are secure.
 WARNING! Before each use check grinding bit is secure, and the bit is not worn or damaged, if damaged, replace
immediately.

 Ensure replacement grinding bits are not damaged (cracks, deformations or splinters etc).
 Always use the correct grinding bit suitable for the material being ground. Ensure the maximum speed specification of the bit is

higher than that indicated on the machine data plate.
 WARNING! Always wear approved eye or face protection when operating the grinder.
 Use breathing protection in accordance with COSHH regulations if fumes or dust pose a hazard. Wear ear defenders and
safety gloves.

 Keep hands and body clear of the workpiece when operating the grinder.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Secure unstable workpiece with a clamp, vice or other adequate holding device.
 Keep children and non essential persons away from the working area.
 Avoid subjecting grinding bit to excessive strain, always ease grinding bit against workpiece (a harsh impact may break the bit).

Maintain a controlled, adequate progression.

 DO NOT get the grinder wet or use in damp or wet locations.
 DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
 DO NOT use the grinder for a task it is not designed to perform.
 WARNING! DO NOT use grinder if damaged or faulty. Contact your local service agent.
 DO NOT use grinder unless you have been instructed in its use by a qualified person.
 DO NOT carry the grinder by the air hose, or yank the hose from the air supply.
 DO NOT direct air from the air hose at yourself or others.
 WARNING! DO NOT grind any materials containing asbestos.
 DO NOT turn the grinder on whilst the grinding bit is in contact with the workpiece.
 DO NOT use grinder where there are flammable liquids, solids or gases such as paint solvents, including waste wiping or

cleaning rags etc as generated sparks may be dangerous.
 DO NOT touch the workpiece close to the ground surface as it will be very hot. Allow to cool. The workpiece may also be very
sharp.

 DO NOT operate grinder if you are tired, under the influence of alcohol, drugs or intoxicating medication.
 When not in use disconnect from air supply and store in a safe, dry, childproof location.

LEAD PAINT WARNING!

Paint once contained lead as a traditional ingredient. Dust from the removal of such paint is toxic and contact with it must be
avoided. The following action must be taken when using the sander on paint that you suspect may contain lead.

1. User must determine potential hazard relating to age of paint to be removed (modern paints do not contain lead).

2. DANGER! Keep all persons and pets away from the work area. The following are particularly vulnerable to the effects of lead paint dust:
Pregnant women, babies and children.

3. We recommend personal protection by using the following safety items:
a) Paint Spray Respirator
b) PE Coated Hooded Coverall
c) Latex Gloves

4. Take adequate measures to contain the paint dust, flakes and scrapings.

5. Continue to wear safety equipment as in (3) above and clean all areas thoroughly when the task is complete.

6. Ensure that paint waste is disposed of, according to local regulations, in sealed bags or containers.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.

GSA674K Issue: 1 - 05/12/14

Original Language Version

© Jack Sealey Limited

2. INTRODUCTION

3. SPECIFICATION

Suitable for die grinding, sanding or panel preparation. Includes our Generation Series 90° air angle die grinder (Model No: GSA674), which
features a safety trigger, contoured rubber handle and 360° rotating exhaust. Supplied in a storage case with a range of die grinding points, sanding
rolls and Ø50/75mm preparation pads. Replacement components readily available.

Model No: .......................................................................GSA674K

Pad Size: .................................................................. Ø50mm, Ø75mm

Thread Size: ........................................................................¼”UNC

Collet Size: ................................................................... Ø3mm, Ø6mm

Free Speed; ......................................................................20000rpm

Air Consumption: ...................................................................... 4cfm

Operating Pressure: ....................................................................90psi

Air Inlet Size: .......................................................................¼” BSP

Weight (tool only): ....................................................................0.54kg

Noise Pressure/Power:.............................................................. 95/84dBA

Vibration/Uncertainty: ............................................................1.44/0.72m/s²

4.1. Air Supply

4.1.1. Ensure grinder air valve (or trigger) is in "off" position before connecting to the air supply.

4.1.2. Use an air pressure of 90psi, and an air flow according to specification.

4.1.3.  WARNING! Ensure the air supply is clean and does not exceed 90 psi while operating the grinder. Too high an air pressure and
unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal ury.

4.1.4. Drain the air tank daily. Water in the air line will damage the grinder.

4.1.5. Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig 1.

4.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4” I.D. and fittings must have the same inside dimensions.

4.1.7. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.

4.2. Couplings.

Vibration may cause failure if a quick change coupling is connected directly to the die grinder.
To overcome this, connect a leader hose to the grinder. A quick change coupling may then be used to connect the leader hose to the air
line recoil hose. See fig 1 & 2.

4. PREPARATION

fig 1 fig 2

GSA674K Issue: 1 - 05/12/14

Original Language Version

© Jack Sealey Limited