instructions for
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
air drill 10mm straight - keyless chuck
model no: gsa232
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
refer to the
instruction
manual
Wear ear
protection
Wear eye
protection
Wear protective
gloves
Wear a mask
1. saFety
WarNiNg! ensure Health & safety, local authority and general workshop practice regulations are adhered to when using this equipment.
WarNiNg! disconnect from the air supply before servicing or performing maintenance.
WarNiNg! Always wear approved eye or face and hand protection when operating the drill. if dust is generated wear a mask.
WarNiNg! ensure correct air pressure is maintained and not exceeded. recommended air line pressure is 90psi.
9 remove ill fitting clothing. remove ties, loose jewellery and contain and/or tie back long hair.
9 maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9 maintain the tool in good condition (use an authorised service agent).
9 replace damaged parts. use genuine parts only. unauthorised parts may be dangerous and will invalidate the warranty.
9 use in a suitable clean and tidy work area, free from unrelated materials. ensure that there is adequate lighting and ventilation.
9 Keep children and unauthorised persons away from the work area.
9 Keep hands away from rotating chuck and drill bit.
9 Keep drill bits clean and sharp for best and safest performance.
9 ensure the workpiece, chuck and drill bit are secure before operating the drill. never hold a workpiece in the hand. use a vice or clamps.
9 Keep the air hose away from heat, oil and sharp edges. check air hose for wear before each use and ensure that all connections are
secure.
9 Prolonged exposure to vibration from this tool poses a health risk. it is the employer’s/owner’s responsibility to correctly assess the hazard
and issue guidelines for safe periods of use and offer suitable protective equipment.
9 When not in use, disconnect from the air supply and store in a safe, dry, childproof location.
8 dO NOt operate the drill unless you have been instructed in its use by a qualified person.
8 dO NOt get the drill wet or use in damp or wet locations.
8 dO NOt use any power source except an air compressor.
8 dO NOt apply excessive loads to the drill bit during operation.
8 dO NOt operate the tool near any inflammable substance or on any container that has held an inflammable substance.
8 dO NOt use the tool for a task it is not designed to perform.
8 dO NOt operate the tool if any parts are damaged or missing as this may cause failure and/or personal injury.
8 dO NOt carry the tool by the hose or pull the hose from the air supply.
8 dO NOt operate drill if you are tired, under the influence of alcohol, drugs or intoxicating medication.
8 dO NOt carry drill with your hand on the power trigger in order to avoid unintentional starting.
8 dO NOt direct air from the air hose at yourself or others.
8 WarNiNg! the warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. it must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
2. iNtrOductiON
textured grip and lightweight aluminium alloy housing provide comfort and control. Powerful air motor provides smooth operation under load.
exhaust outlet adjusts 360° keeping air flow away from operator. fitted with safety release trigger control to prevent accidental operation. fitted
with Jacob’s keyless chuck for fast bit changes.
3. speciFicatiON
model no: ..................................................................GsA232
chuck size: ..................................................................10mm
free speed: ..............................................................2500rpm
Air consumption: ............................................................4cfm
operating pressure: ...................................................... 90psi
Air inlet size:............................................................. 1/4”BsP
Weight: ........................................................................0.95kg
noise Power: ...........................................................105dB(A)
noise Pressure: ........................................................94dB(A)
Vibration: ....................................................................1.6m/s²
uncertainty: ................................................................0.8m/s²
© Jack sealey limited
Original Language Version
GsA232 | issue:2 (sP) 04/04/17
4. OperatiON
safety catch
throttle lever
Grip this section
turn this section
to open/close jaws
Fig.1
Fig.2 Fig.3
4.1. air supply
WarNiNg! ensure the air supply is clean and does not exceed 90psi while operating the drill. too high an air pressure and unclean air
will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.1. ensure drill air valve (or trigger) is in the “off” position before connecting to the air supply.
4.1.2. You will require an air pressure of 90psi, and an air flow according to specification.
4.1.3. drain the air tank daily. Water in the air line will damage the drill.
4.1.4. clean air inlet filter weekly. recommended hook-up procedure is shown in fig 1.
4.1.5. line pressure should be increased to compensate for unusually long air hoses (over 8 metres). the minimum hose diameter should be
1/4” internal diameter and fittings must have compatible dimensions.
4.1.6. Keep hose away from heat, oil and sharp edges. check hose for wear, and make certain that all connections are secure.
4.2. couplings.
Vibration may cause failure if a quick change coupling is connected directly to the drill. to overcome this, connect a leader hose to the
drill (sealey ref: AH2r or AH2r/38). A quick change coupling may then be used to connect the leader hose to the air line recoil hose.
see fig 2 & fig 3.
5. OperatiON
WarNiNg! ensure you read, understand and apply section 1 safety instructions.
5.1. Gripandturnthechuckasindicatedin(g.1)toopenthejaws,insertthedrillbitfulldepth,gripandturnchuckintheopposite
direction to close the three jaw chuck and clamp drill bit.
5.2. connect the drill to the air hose as described in section 4.
5.3. Push the safety catch (fig.1) forward and depress the throttle lever to operate the drill.
6. maiNteNaNce
WarNiNg! disconnect drill from the air supply before changing accessories, servicing or performing maintenance. replace or repair
damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
6.1. lubricate the air drill daily with a few drops of sealey air tool oil dripped into the air inlet to prolong its life.
6.2. clean the drill after use.
6.3. loss of power or erratic action may be due to the following:
a) excessive drain on the air line. moisture or restriction in the air pipe. incorrect size or type of hose connectors. to remedy check the
air supply and follow instructions in section 4.
b) Grit or gum deposits in the drill may also reduce performance. if your model has an air strainer (located in the area of the air inlet),
remove the strainer and clean it. flush the drill out with gum solvent oil or an equal mixture of sAe no 10 oil and paraffin.
Allow to dry before use.
6.4. for a full service contact your local sealey service agent.
6.5. When not in use, disconnect from air supply, clean drill and store in a safe, dry, childproof location.
© Jack sealey limited
Original Language Version
GsA232 | issue:2 (sP) 04/04/17
Loading...