Sealey FH2009.V2 Instruction Manual
INSTRUCTIONS FOR:
FAN HEATER 2000W
MODEL: FH2009.V2
Thank you for purchasing a Sealey Fan Heater. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.2. GENERAL SAFETY
WARNING!Disconnect the heater from the mains power, before servicing or performing any maintenance. Servicing or
maintenance must only be carried out by an authorised service agent.
Check that the heater is in sound condition and good working order. Take immediate action to repair or replace damaged parts.
Use recommended parts only. Unapproved parts may be dangerous and will invalidate the warranty.
WARNING! DO NOT use the heater near flammable material, liquids, solids, gases or compressed gas cylinders and the like.
DO NOT obstruct the air inlet or outlet on the heater.
DO NOT cover the heater.
DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT touch the heater casing or grill when first switched off as these are hot and will take time to cool.
DO NOT use the heater for anything other than its intended purpose. It is not suitable for drying clothes or laundry.
DO NOT place the heater close to a bath, wash basin, shower, swimming pool or any other water-filled area or wet surface.
DO NOT get the heater wet or use in areas of high condensation.
DO NOT place the heater up against any surface such as a wall, door or furniture etc.
DO NOT place the heater immediately below any electrical outlet.
DO NOT allow the power lead to lie in front of the heater outlet.
DO NOT attempt to repair a damaged heater, contact an authorised service agent.
DO NOT stand on the heater.
DO NOT connect the fan heater to a timer device or other equipment that can automatically switch the heater on or off.
Ensure that the heater is correctly turned off when not in use and store in a safe, dry area, out of reach of children.
1.1. ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs,
sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the
installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main
distribution board. We also recommend that a Residual Current Device (RCD) is used. It is particularly important to use an
RCD with portable products that are plugged into a supply which is not protected by an RCCB. If in any doubt consult a
qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by
a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those
appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1.
and 1.1.2. and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check
all connections to ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply to
be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have
any faulty item repaired or replaced by a qualified electrician. When a BS 1363/A
UK 3 pin plug is damaged, cut the cable just above the plug and dispose of the
plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable
outer insulation extends beyond the cable restraint and that the restraint is tight. Double insulated products, which are
always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only. To rewire, connect the wires as
indicated above. DO NOT connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified
electrician to ensure that a suitably rated supply is available. We recommend that you discuss the installation of
an industrial round pin plug and socket with your electrician.
1.1.11. If an extension reel is used it should be as short as possible and fully unwound before connection. A reel with an RCD
fitted is preferred since any appliance plugged into it will be protected. The cable core section is important and should be
at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this product and for others which may
be used in the other output sockets, we recommend the use of 2.5mm² section cable.
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
Brown
Live
Wire
FUSE RATING 13 AMP
Original Language Version
FH2009.v2 Issue: 1 - 14/06/10
4. MAINTENANCE
3.1 Position heater where required on a level surface
ensuring that the air intake and outlet are not
obstructed in any way.
3.2 Plug the heater into the mains supply.
3.3 Set the thermostat knob to the half way position as
shown in fig.1.
3.4 The selector switch has four positions which are
repeated on either side of the knob. See fig.1.
3.5 The fan heater will switch on when the selector switch
is set to one of the two power settings (1000W or 2000W).
3.6 Once the room reaches the set temperature the
heater will switch on and off automatically to maintain
that temperature. Adjust the position of the thermostat
knob to obtain a comfortable room temperature.
3.7 If the fan fails to operate when a power setting is
selected the thermostatic temperature control may be
set too low. Turn the knob slowly towards max until
the fan starts.
3.8 For a cooling effect turn the selector switch to the fan
only setting.
2. SPECIFICATIONS
Tough metal casing with composite integral carry handle.
Two-position heat settings control two 1000Watt heating
elements. Full range ambient room thermostat maintains
temperature at pre-set level. Fan doubles as cool air blower for
use in the summer. Full CE approval. Supplied with 13Amp
non-rewirable ASTA approved plug.
Model .......................................FH2009
Voltage/Frequency:.........................230V ~50Hz
Power Rating:.............................1000/2000W
Heat Settings:.........................1000W or 2000W
Dimensions: ......................... 200 x 258 x 95mm
Weight: ........................................1.5kg
WARNING! Before attempting any maintenance ensure the unit is unplugged from the mains power supply and that it
is cool.
4.1. Clean the heater with a soft dry cloth. DO NOT use abrasives or solvents.
4.2. Periodically check the heater grille to ensure it is not blocked.
No other maintenance is necessary. If you experience a problem with your heater or if the power lead or plug is damaged
contact your local authorised service agent for repair. DO NOT dismantle or tamper with the heater as this may be
dangerous and will invalidate your warranty.
3. OPERATION
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
sales@sealey.co.uk
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version
FH2009.v2 Issue: 1 - 14/06/10
WARNING! This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
Loading...