Sealey CP36S.V2 Instruction Manual
INSTRUCTIONS FOR:
CORDLESS LITHIUM-ION SCREWDRIVER SET
46 PIECE 3.6V
PART NO: CP36S.V2
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
Refer to
Instruction
Manual
Wear Eye
Protection
1. SAFETY
2. INTRODUCTION
1.1. GENERAL SAFETY
Maintain the screwdriver in good condition. Check moving parts alignment on a regular basis.
Keep the screwdriver and charger clean for best and safest performance.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
Secure loose workpieces with a clamp, vice or other adequate holding device.
Avoid unintentional starting.
Wear approved safety eye protection.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the working area.
DO NOT allow children to operate the screwdriver.
DO NOT hold unsecured workpiece in your hand.
DO NOT carry the screwdriver with your finger on the trigger.
DO NOT use the screwdriver for a task it is not designed for.
DO NOT operate the screwdriver when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT get the screwdriver or battery charger wet or use in damp or wet locations.
Keep screwdriver and charger in a safe, dry, child proof area where the temperature will not exceed 104°F (40°C).
1.2. ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING SCREWDRIVER TO THE POWER SUPPLY.
WARNING! It is the user’s responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current
Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device)
is used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an
RCCB. You must also read and understand the following instructions concerning electrical safety.
1.2.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the
appliance and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3. You must ensure that you:
Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power
supply. If worn or damaged DO NOT use.
Important: Check that the voltage marked on the charger plug is the same as the power supply to be used.
DO NOT pull the charger plug from the mains socket by the lead.
DO NOT use any other type of charger with this product.
DO NOT try to take the charger plug apart.
DO NOT use the charger plug to charge or power any other electrical item.
DO NOT get the charger wet, or use in wet, damp conditions (for indoor use only).
WARNING! NEVER substitute a standard 13amp 3 pin plug, or any other type of plug, for the charger plug.
1.3. BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
DO NOT attempt to open, disassemble, modify or service the battery pack.
DO NOT crush, puncture, short external contacts or dispose of in fire or water.
DO NOT expose to temperatures above 60°C (140°).
Recycle or dispose of used battery as stipulated by local regulation.
Forward, reverse and trigger-lock with soft grip handle for comfort and control. Features locking swivel adjustment from pistol to straight type and
built-in LED work light in base of handle for use in low light areas. Adjustable torque with six settings 6mm quick-release bit holder. Integral LED
light to illuminate working area. Lithium-ion battery maintains a high energy density level and has no memory effect, lasting longer than traditional
Ni-Cd cells and will recover from a deep discharge state. Three LEDs indicate battery life. Supplied in carry-case with a set of accessories.
CP36S.V2 Issue No:1 - 21/07/15
Original Language Version
© Jack Sealey Limited
fig.1
3. SPECIFICATION
4. OPERATION
Model No: ........................... CP36S.V2
Battery: ..................................3.6V
No Load Speed: .......................0-200rpm
Maximum Torque: ........................ 3.5Nm
Charging Time: ........................... 3.5hr
Vibration: ....................................0.37m/s²
Uncertainty: ...................................1.5m/s²
Noise Pressure: ...............................55dB(A)
Noise Power: .................................66dB(A)
fig.2
IMPORTANT WARRANTY INFORMATION:
The battery fitted to this cordless tool is considered to be a consumable item and its ability to accept charge will reduce over time. Our
warranty will cover genuine battery malfunction, but not fair wear and tear, for a period of 12 months.
3.1. To charge the screwdriver, insert the charger jack into the charging
socket on the screwdriver (fig.1) and plug the charger into a mains socket.
3.2. The red indicator light (fig.2) will illuminate to indicate the battery is being charged. When charging is complete, unplug the charger from
the mains and the screwdriver. To check the level of charge, press the charge display button. When the green button is lit, the battery is fully
charged.
3.3. Place a bit into the bit holder of the screwdriver. Select the required direction by using the reverse switch (which will lock the screwdriver in its
central position) and squeeze the trigger to start the screwdriver. The LED spotlight will light with initial pressure on the trigger.
3.4. The LED worklight in the handle can be switched on or off by pressing the lens
3.5. To check the condition of the battery, press and hold down the charge display button next to the charge indicator lights(fig.2). If all LEDs
illuminate, there is sufficient charge, if just the yellow and red LEDs illuminate, the screwdriver will soon need charging, if just the red LED
illuminates, the screwdriver needs to be charged immediately.
3.6. To change the position of the handle, press the handle lock and turn the handle around 180° until it clicks into position (fig.2)
3.7. To select torque or drill setting, twist the torque selector around to the required setting - from 1 (the lowest) to 6 (the highest) for
torque setting or to the drill symbol for drilling.
3.8. When finished working, remove the bit from the bit holder, pulling back the quick release bit holder if needed. Clean the screwdriver
and replace all parts in the storage case. Store the case in a safe, dry, child proof location.
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Battery Removal
To remove battery for disposal, unfasten the six screws in the grip then remove by cutting the connecting wires.
Dispose of the battery in accordance with local authority regulations.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential
purchasersofproductscontainingbatteries(asdenedwithintheseregulations),thattheyareregisteredwithValpak’s
registeredcompliancescheme.JackSealeyLtd’sBatteriesProducerRegistrationNumber(BPRN)isBPRN00705.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534
sales@sealey.co.uk
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Contents:
Screwdriver Bits: Slotted - 3, 4, 5, 6, 7mm, Phillips - #0, #1, #2, #3. Pozi:- #0, #1, #2, #3, TRX Star - T10, T15, T20, T25, T27, T30, T40,
T45, Hex - 2, 2.5, 3, 3.5, 4, 5, 6mm. 55mm Screwdriver Bits: Slotted - 4, 6mm. Phillips - #0, #2.Socket Adaptor. Sockets - 6, 7, 8, 9, 10, 11,
12, 13mm. Magnetic Bit Holder. Drill Bits - 1.5, 3mm.
CP36S.V2 Issue No:1 - 21/07/15
Original Language Version
© Jack Sealey Limited
Loading...