Sealey CP313 Instructions Manual
1. SAFETY
INSTRUCTIONS FOR:
CORDLESS RIVETER LITHIUM-ION 18V 1.5Ah
1hr CHARGER
MODEL No: CP313
WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this
equipment.
Familiarise yourself with the applications, limitations and potential hazards peculiar to the riveter.
Maintain the riveter in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Keep the work area clean, uncluttered and ensure that there is adequate lighting.
Keep the riveter clean for best and safest performance.
WARNING! Always wear approved eye or face protection when operating the riveter.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain, and/or tie back, long hair.
Keep the riveter away from your body and at a safe distance from others.
Keep children and unauthorised persons away from the work area.
Secure unstable workpiece with a clamp, vice or other adequate holding device.
Ensure that spent rivet stems are disposed of correctly and do not cause a hazard.
DO NOT use the riveter for any purpose other than that for which it is designed.
DO NOT get the riveter wet or use in damp or wet locations or areas where there is condensation.
DO NOT allow untrained persons to operate the riveter.
DO NOT point or fire the riveter at people or animals.
DO NOT operate the riveter when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT operate the riveter in a flammable or explosive atmosphere.
1.1. ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Inspect power supply cables and plugs regularly for wear or damage and check all connections to
ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Have any faulty item repaired
or replaced immediately by a qualified electrician. When a BS 1363/A UK 3 pin plug is damaged,
cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and that the
restraint is tight.
Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only. To
rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
RECOMMENDED
FUSE RATING: 3AMP
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
Refer to
Instruction Manual
Wear Eye
Protection
Original Language Version
© Jack Sealey Limited
CP313 Issue: 1 - 24/12/15
3. SPECIFICATION
2. INTRODUCTION
Model No: .................................................CP313
Nozzle Sizes: ......................................2.4, 3.2, 4, 4.8mm
Battery Type: ...................................18V 1.5Ah Lithium-ion
Maximum Pulling Force:....................................... 6000N
Maximum Stroke: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21mm
Replacement Battery:.......................................CP313BP
Weight: .....................................................1.8kg
Blind Rivet Type:...................................................
Aluminium: ....................................................Yes
Steel: ........................................................Yes
Stainless Steel:.................................................Ye s
Copper:.......................................................Ye s
g.1
g.2
g.3
g.4
Original Language Version
© Jack Sealey Limited
CP313 Issue: 1 - 24/12/15
Battery charger safety instructions
WARNING! DO NOT attempt to charge any battery other than that supplied for the product. Other types of batteries may explode!
All mains electrical supply safety features must be followed as described in 1.31. above.
Disconnect the charger from the mains supply when not in use.
DO NOT charge battery if room temperature is below 10°C (50°F) or above 40°C (104°F).
DO NOT expose the charger to damp or wet conditions.
DO NOT pull or carry the charger by the power lead.
DO NOT operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Take the charger to an authorised
agent for repair or obtain a replacement.
DO NOT dismantle the charger as this may cause damage and/or personal injury and will invalidate the warranty.
DO NOT insert foreign objects or material into the hole reserved for the battery pack.
DO NOT recharge a second battery pack immediately after charging the rst. Consecutive charging will overheat the charger. Allow
the unit to cool for 15 minutes before charging the next pack.
DO NOT attempt to connect two chargers together.
Store the charger in a cool, dry place out of reach of children.
Suitable for aluminium, steel, stainless steel and copper rivets from 2.4 to 4.8mm. Powered by a 18V 1.5Ah Lithium-ion battery with a pulling
force of up to 6000N, capable of pulling up to 250 rivets on one full charge. Digital display showing battery charge level. Hardened steel jaw
assembly, which returns to start position once the rivet has been secured. Supplied with four riveting nozzles, spanner, and 1hr mains charger.
Metal carry-case for safe and secure storage.
Loading...