instructions for
MPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
2.5tonne axle st ands
model no: as2500
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
refer to
instructions
1. safety
WaRnInG!
do not oveRload axle stands beyond Rated capacIty. oveRloadInG can cause daMaGe to, oR faIluRe of,
the axle stands. posItIon load on centRe of cRutch/saddle only. alWays use stands In paIRs on haRd
level suRface capable of sustaInInG the load. use of stands on otheR than haRd level suRfaces can
Result In load InstabIlIty and possIble loss of load. do not use on taRMacadaM. faIluRe to folloW
these InstRuctIons May Result In daMaGe to axle stands, loss of load ResultInG In pRopeRty daMaGe,
seRIous peRsonal InjuRy oR loss of lIfe.
▲ danGeR! GReat caRe Must be taKen to ensuRe you loWeR the vehIcle (oR otheR load)
sloWly and caRefully onto the centRes of the cRutch/saddle of the axle stands.
9 use only as specified by the manufacturer.
9 ensure the load does not exceed the maximum capacity as marked on the axle stand, per pair.
9 use no more than a single pair of stands either on the front, rear or one side of the vehicle. use in pairs.
9 no alterations or modifications shall be made to this product.
9 use on a hard, level surface, e.g. concrete. do not use on uneven ground or tarmacadam.
9 securely chock wheels in contact with the ground. Before jacking and placing the stands, apply vehicle
handbrake (put automatics in ‘Park’).
9 make sure that each stand is securely located under a strong point on the vehicle; consult the vehicle manufacturer’s handbook for
guidance. ensure that height adjust locking mechanism is fully located before applying any load to the axle stand.
9 ensure that the load is located centrally on the saddle, and that the weight is directed through the vertical axis of the stand.
9 exercise extra care when using with a three wheeled vehicle or a trailer. refer to vehicle manufacturer’s instructions.
9 once vehicle is supported, ensure that the vehicle and stands are stable before starting work. ensure that it is not possible for the
vehicle to move before commencing any work.
9 inspect stands before each use. do not use if they show signs of damage. do not use if it is suspected that they have been
overloaded.
9 Before commencing any work or going beneath the vehicle, undertake a risk assessment. ensure that a responsible person is aware of
the work about to be undertaken.
9 replace any labels on the axle stand should they become unreadable. this applies in particular to any warning or operation instruction
labels. if replacement labels are required, contact your sealey stockist.
8 do not use axle stands on the highway, or anywhere else if it is deemed to be unsafe.
8 do not push or twist the vehicle/load whilst it is supported on stands.
8 do not mix components between stands. use only as supplied.
8 do not allow children or animals in the vicinity of a vehicle supported on axle stands.
8 do not leave a vehicle on axle stands in an area that could be considered a hazard to others or property.
9 folloW steps 1, 2, and 3 to place vehIcle / load coRRectly onto axle stands.
© Jack sealey limited
Original Language Version
As2500 | issue 6 (sP) 12/01/17
2. IntRoductIon
All steel vehicle support stand with pin and chain. full width V-crutch for safe support of load. manufactured to vigorous safety standards. Proven
workshop quality and reliability. sold in pairs.
3. specIfIcatIon
Model no: ................................................................. as2500
capacity each: ........................................2.5tonne (2,500 kg)
capacity Pair: .............................................5tonne (5,000 kg)
minimum Height: ........................................................ 345mm
maximum Height: ....................................................... 505mm
4. opeRatIon
4.1. refer to vehicle handbook for correct jacking procedure and points. check to ensure manufacturer’s recommended jacking points are in
4.2. Position stands under recommended strong points and adjust to the required height.
good condition.
WaRnInG! IN THE HIGHEST POSITION BOTH ARMS OF THE ‘U’ PIN MUST PASS THROUGH THE UPPER COLUMN -
THERE MUST NEVER BE MORE THAN FOUR HOLES VISIBLE ABOVE THE LOWER COLUMN (fig.1).ENSURE THAT THE ‘U’ PIN
HAS PASSED RIGHT THROUGH THE UPPER AND LOWER COLUMN SO THAT BOTH ENDS ARE VISIBLE (fig.2)
lower the load onto stands carefully and slowly. ensure load bearing points sit in the centres of the stand crutches and that the stands
are stable. Also ensure that there are no objects or persons that could impede the safe lowering of the vehicle onto the stands.
▲ DANGER! You must follow instructions carefully and DO NOT load stand off centre. Failure to heed these warnings may cause damage
and/or injury or loss of life!
5. MaIntenance
5.1. Before each use, check that stands and stand welds are not cracked and that there are no missing or damaged parts.
5.2. Any suspect axle stand must be removed from service immediately.
5.3. owing to the potential hazards associated with stands, do not misuse, or make any modification to, the stands or components.
5.4. it is the responsibility of the owner to ensure that the operator has read these instructions, together with the safety features on the side of
the stand, and that the operator is familiar with the use and limitations of the stands.
g.1
g.2
Recycle unwanted materials instead of disposing of them as waste. all tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
IMpoRtant: no liability is accepted for incorrect use of this product.
WaRRanty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
environmental protection
01284 757500
01284 703534
www.sealey.co.uk
Web
sales@sealey.co.uk
© Jack sealey limited
Original Language Version
As2500 | issue 6 (sP) 12/01/17
Loading...