Sealey AP900R, AP1200R Instruction Booklet

5 LEVEL RACKING UNITS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
340KG/220KG CAPACITY PER LEVEL
mODEL NO’S: AP900R/AP1200R
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
Refer to
instruction
manual
Wear protective
gloves
1. SAFETY
WARNING! Ensure Health & Safety, and local authority regulations are adhered to when assembling and using these shelves. 9 Locate shelves in a suitable area where they will not be an obstruction. 9 Keep the general area clean, uncluttered and ensure there is adequate lighting.
WARNING! Erect shelves on a level and solid surface such as concrete. 9 Keep children and unauthorised persons away from the storage area.
8 DO NOT use the shelves for any purpose other than that for which they are designed. 8 DO NOT site the shelves out of doors. 8 DO NOT get the shelves wet or use in damp or wet locations or areas where there is condensation. 8 DO NOT clean the shelf supports with any solvents which may damage the coated surface.
9 Ensure that the shelves are properly assembled before loading them with any items. 9 Where possible the unit should be fixed to the wall with suitable fixings 9 Place heavier items on the lower shelves. 9 Where possible heavier items should be evenly distributed across the shelves.
2. INTRODUCTION
Fully painted steel frame with ve chipboard shelves. 340/220kg capacity per level giving a maximum capacity of 1700kg/1100kg per rack depending on model. Boltless design means no tools required to assemble. Slots together in minutes. Two piece uprights allow use as a single
bay rack or split into two separate shelf systems or workstations.
3. SPECIFICATION
Model no. AP900R AP1200R
Overall size W x D x H 915 x 460 x 1830mm 1220 x 460 x 1830mm Capacity 1700kg 1100kg Shelf capacity 340kg 220kg Nett weight 23.3kg 33.66kg
1
fig.
© Jack Sealey Limited
Original Language Version
fig.
2
AP900R, AP1200R| Issue:3 (3) 26/02/19
4. CONTENTS
4.1. Carefully unpack the product and check the contents against g.3. Should any items be damaged or missing contact your Sealey stockist.
3
fig.
fig.
4
5. ASSEMbLY Fig.4
5.1. Fig.4
Support two upright angle posts (A) in a vertical position ensuring that the keyhole slots are pointing downwards. Join them together at the base using a short ‘Z’ beam (C) ensuring that the shelf support is facing upwards. Tap the beam at either end, close to each angle
post to ensure that the rivets are seated at the bottom of the keyhole slots.
5
fig.
6
fig.
5.2. Fig.5
Continue to assemble the complete bottom frame in the order indicated above in fig.5 starting with a long ‘Z’ beam (B). Ensure that each ‘Z’ beam is facing upwards. Tap the beam at either end, close to each angle post to ensure that the rivets are seated at the bottom of the
keyhole slots.
5.3. Fig.6
Now make up an upper end frame by connecting two angle posts together at the top with a short ‘Z’ beam (C). Tap the beam at either end to ensure that the rivets are properly seated at the bottom of the keyhole slots. Take a second short ‘Z’ beam and insert the top rivets into the bottom keyholes. Only use the top rivets, the bottom rivets will be used to join the bottom and upper frames. Make up a
second upper end frame using the remaining two angle posts and a two short ‘Z’ beams.
© Jack Sealey Limited
Original Language Version
AP900R, AP1200R| Issue:3 (3) 26/02/19
Loading...
+ 3 hidden pages