INSTRUCTIONS FOR
MPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
RACKING UNIT 5 LEVEL - 200KG CAPACITY
PER LEVEL
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
Refer to
instructions
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this racking
unit.
9 Locate racking unit in a suitable work area.
9 Keep the work area clean, uncluttered and ensure there is adequate lighting.
WARNING! Use racking unit on level and solid ground, preferably concrete. For added safety fix unit to a wall.
9 Keep the racking unit clean and tidy in accordance with good workshop practice.
9 Keep children and unauthorised persons away from the work area.
8 DO NOT use the racking unit for any purpose other than that for which it is designed.
8 DO NOT use the racking unit outdoors.
8 DO NOT place the racking unit in a damp or wet location or an area where there is condensation.
8 DO NOT clean the racking unit with any solvents which may damage the surfaces or the protective coating.
8 DO NOT move the racking unit when there are items placed on it.
8 DO NOT overload the racking unit.
MODEL NO: AP7200.V2
2. INTRODUCTION
Fully painted steel frame with ve MDF shelves. 200kg capacity per level giving a maximum capacity of 1000kg per rack. Boltless design means no
tools required to assemble. Two piece uprights allow use as a single bay rack or split into two separate shelf systems or workstations. Ideal for use
in conjunction with Model No. AP7150C corner racking unit.
Dimensions W x D x H: 900 x 400 x 1830mm
3. CONTENTS
3.1. Unpack the unit and conrm that all the parts listed below are present.
3.2. Assemble the unit on a solid, level surface. Avoid carpet. A second person will be required to help with assembly.
© Jack Sealey Limited
Original Language Version
AP7200.V2 | Issue:1 18/01/17
4. ASSEMBLY
4.1. Assemble the racking unit in the sequence below, referencing the parts list overleaf.
4.2. Use a rubber mallet to tap the brackets together.
Step 1
Place foot end caps onto the bottom of
the 4 legs ‘D’. Note: upright position.
Place the shelving brackets ‘A’ onto the
legs ‘D’. A rubber mallet can be used to
lightly tap all brackets into the keyholes
of the legs into place. Allow one keyhole
free between the foot and cap and
shelving bracket.
Step 2
Use shelf bracket ‘B’ for the side
brackets using the shelf bracket from
Step 1 as a guide for height. Allow 1
keyhole free from the ground as shown
in the diagram. Use same shelving
brackets for opposite sides as shown in
the diagram. Place brace ‘C’ as shown.
Step 3
Place MDF board on bottom shelf to
minimise buckling. Join the
upper legs to the lower legs with
the connector pins. Note upright
position. Note: The legs are designed
to sit directly on top of each other
– don’t overlap them.
Handy Hint: A
Flathead screwdriver may be used to
tap in connector pins.
Step 4
Fix brackets ‘B’ so that the top
rivet sits on the upper legs and
the bottom rivets sit on the lower
legs. Repeat with brackets ‘A’,
followed by brace ‘C’ as shown.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Step 5 Step 6
Fix brackets ‘B’ at the very top
allowing room for the MDF board
to sit flush against the legs.
Repeat with brackets ‘A’.
Apply remaining brackets as
above to desired height. Ensure
that braces ‘C’ are fixed to all
shelves.
Environmental Protection
Step 7
Place the MDF boards on
shelves, ensure they are sitting
flush against the edge of the
shelf brackets.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey Limited
Sole UK Distributor, Sealey Group.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds,Suffolk.
IP32 7AR
Original Language Version
01284 757500
01284 703534
www.sealey.co.uk
Web
sales@sealey.co.uk
AP7200.V2 | Issue:1 18/01/17
Loading...