instructions for:
heaVy Duty eLectronic
soLDerinG torch
model no: ak2932
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to
these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLease reaD these instructions carefuLLy. note the safe oPerationaL reQuireMents, WarninGs
anD
cautions.
Do so May cause DaMaGe anD/or PersonaL inJury anD WiLL inVaLiDate the Warranty. PLease keeP instructions
safe for future use.
1. safety instructions
WarninG! ensure Health & safety, local authority, and general workshop practice regulations are adhered to when using
this equipment, make sure you know where the nearest fire extinguisher is.
WarninG! Always wear approved eye / face protection when operating the torch.
WarninG! do not use the torch if you notice damage to the workpiece or if there could be a gas leak from it.
WarninG! Butane gas is extremely flammable, handle with care.
WarninG! Always point the torch away from the eyes and body when igniting and during operation.
WarninG! do not put the torch down when it is lit, do not leave it unattended.
WarninG! the flame is not easily visible in the bright daylight.
WarninG! ensure the flame is completely extinguished after use. do not use water to cool the torch down.
WarninG! only use in a well ventilated area.
Do not use the torch in an area where paint fumes, solvents or other flammable solids, liquids or gases pose a potential
hazard. Keep flammable material away from the torch when operating.
Do not operate the torch when you are tired or under the influence of alcohol, drugs or intoxicating medication.
Do not hold any workpiece by hand.
Do not touch the workpiece close to the heated area as it will be very hot. Allow to cool.
Do not operate the torch if it is damaged as this may cause failure and/or possible personal injury.
Do not touch the top of the torch during or immediately after use, as it will be very hot. Allow to cool.
Do not allow children to operate the torch.
After use, apply the safety lock and allow the torch to cool before storing it.
When not in use, store away from direct sunlight in a safe, dry, childproof location.
Do not store at over 40°c, such as in a car in hot weather.
2. introDuction
Heavy duty butane powered heating and soldering torch. Fitted with piezoelectric ignition with anti are burner, ignition lock and
continuous ame switch. Produces an adjustable ame with a maximum temperature of 1300°C and will operate on a single ll for up
to 75 minutes.
3. oPeration
3.1 to fiLL. (refer to fig.1)
use standard butane fuel. fill in a well ventilated area away
from open flame. turn the torch off, make sure the flame is
out, allow to cool down for five minutes before filling.
3.1.1. Hold torch upside down and insert the filling can’s
nozzle into the gas filling valve. Press nozzle into the valve
and release gas. once gas begins to seep out around the
edge of the nozzle, the gas tank is full. remove the filling can.
3.2 to use. (refer to fig.1)
3.2.1. centre the gas adjustment dial between the (+) and (-) signs.
using your thumb, pull down the safety switch.
3.2.2. to light the torch hold it in your hand, use thumb to press and
hold down the ignition button, (it may take two or three times
before the torch ignites). each attempt will require pulling
down the safety switch, then pressing the ignition button
again.
3.2.3. to adjust the flame intensity, use the gas adjustment dial.
3.2.4. for a continuous flame, before releasing the ignition button,
move the continuous flame button to the right.
3.2.5. to turn the torch off, move continuous flame button to left.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMPortant: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
inforMation: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
© Jack sealey limited
use this ProDuct correctLy anD With care for the PurPose for Which it is intenDeD. faiLure to
g.1
sole uk Distributor, sealey Group,
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk,
P32 7Ar
i
Original Language Version
01284 757500
01284 703534
www.sealey.co.uk
Web
sales@sealey.co.uk
email
AK2932 issue: 1 - 11/04/13
Loading...