SPACE WARMER PARAFFIN/KEROSENE/DIESEL
MPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
HEATER
MODEL NO’S: AB1008.V3, AB1258.V3, AB1758.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
Refer to
instructions
This product is not suitable for primary heating purposes
Warning:
Hot surface
Warning:
Automatic
start up
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey dealer.
If the heater is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is tted with the correct
fuse - see fuse rating in these instructions.
8 DO NOT pull or carry the appliance by the power cable.
8 DO NOT pull the plug from the socket by the cable.
8 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
replaced immediately by a qualied electrician.
1.1.4. This product is tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualied electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualied electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualied electrician.
1.1.10 If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is
preferred since any appliance plugged into it will be protected. The cable core section is important and
should be at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this product and for others which may be
used in the other output sockets, we recommend the use of 2.5mm² section cable.
1.2. GENERAL SAFETY
▲ DANGER! Risk of carbon monoxide poisoning. Failure to provide proper ventilation could result in serious illness or death.
9 Check that the heater is in sound condition and good working order. Take immediate action to repair or replace damaged parts.
9 Use recommended parts only. Unapproved parts may be dangerous and will invalidate the warranty.
WARNING! Only use clean paran, kerosene or diesel (NOT BIO-DIESEL) to fuel your heater, in accordance with instructions
contained in this manual.
WARNING! Keep spare fuel in suitable containers and away from sources of heat or ignition.
9 Keep the front of the heater a minimum of 2.5 metres from any combustible materials (i.e. wooden items, cloth, plastics, paper,
tarpaulins etc).
WARNING! Only use heater outdoors or in well ventilated areas. Only operate on a level and stable surface.
WARNING! DO NOT use the heater near ammable material, liquids, solids, gases or compressed gas cylinders.
8 DO NOT use the heater in closed rooms, living areas, basements or below ground level.
8 DO NOT allow untrained persons to operate the heater and DO NOT operate the heater without the cover.
8 DO NOT move or handle the heater when hot.
8 DO NOT leave the heater unattended when in use. Switch the heater o and unplug from the mains before leaving work area.
8 DO NOT ll the fuel tank whilst the heater is running or still hot. Stop heater and allow to cool before refuelling.
8 DO NOT overll the fuel container. Wipe up any spilt fuel immediately.
8 DO NOT obstruct the air inlet (rear) and air outlet (front) of the heater.
8 DO NOT use duct work in front or at the rear of the heater.
8 DO NOT allow children or animals near the heater when in use, or while hot.
Recommended fuse rating
5 Amp
© Jack Sealey Limited
Original Language Version
AB1008.V3, AB1258.V3, AB1758.V3 Issue:3 27/11/18
WARNING! RISK OF ELECTRIC SHOCK. DO NOT expose the heater to water spray, rain, dripping water or wind.
8 DO NOT operate the heater when you are tired or under the inuence of alcohol, drugs or intoxicating medication.
8 DO NOT touch the heater outlet or dome when rst switched o as these are very hot and will take time to cool.
8 DO NOT unplug the heater to switch it o. Use the ON/OFF switch.
9 Ensure that the heater is correctly turned o when not in use. Store in a safe, dry area, with the fuel tank empty out of reach of
children.
NOTE: This appliance is not intended for persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
2. INTRODUCTION
Our range of paraffin / kerosene / diesel heaters represents excellent value. Workshop tried and tested. All models have an adjustable thermostat
(C°) that cuts in as desired temperature is reached. Models are fitted with digital room temperature (C°) display , spare parts storage compartment and
heavy duty solid wheels. Proven pump systems handle either paraffin, kerosene or diesel with no adjustment of air compressor required. All models are
fitted with fuel tank gauge and heavy-duty filler cap.
Sealey Advantages
• PARAFFIN, KEROSENE OR DIESEL - The Sealey AB heaters will operate on all.
• CLEAN BURNING - A specially designed burner head in a stainless steel combustion chamber ensures a more thorough burn of fuel
which means greater fuel economy and maximum heating effect.
• FILTER PROTECTION - The compressor unit is protected by extra large filter elements.
• LARGE FUEL TANK - The AB series heaters will operate for between 8 and 11 hours on a single fill of fuel.
• SAFETY FEATURES - The AB series heaters are fitted with a flame-out device which cuts the fuel supply when the flame is
inadvertently extinguished.
• QUALITY - Manufactured to comply with the rigorous standards.
• AFTER SALES SERVICE - The best after sales service in the business. Full spares back up for all models.
3. SPECIFICATION
Model no AB1008 AB1258 AB1758
Output 29.3kW/
100,000Btu/hr
Tank capacity 38ltr 38ltr 49ltr
Fuel Paran/Kerosene/
Diesel
Supply 230V - 5A 230V - 5A 230V - 5A
Running time per
lling
(maximum)
Transport wheels Yes Yes Yes
Airow 520cfm 540cfm 630cfm
Automatic shut o Yes Yes Yes
Heated area 20,000ft³/566mtr³ 24,800ft³/702mtr³ 34,400ft³/974mtr³
Weight 24.5kg 24.5kg 27.7kg
11hr 10hr 9.5hr
36.6kW/
125,000Btu/hr
Paran/Kerosene/
Diesel
51.3kW/
175,000Btu/hr
Paran/Kerosene/
Diesel
4. ASSEMBLYs
4.1. Slide axle through wheel support frame, slide a bushing and flat
washer (A) to each end of the axle.
4.2. Install wheels with valve stem on the outside, slide flat washer
(B) onto the axle and then using a cotter pin bend the legs of
the pin with pliers to secure. Snap on the wheel caps onto the
flat washer (B).
4.3. Place heater on wheel support frame ensuring that the air inlet
is by the wheels and place the heater onto the frame lining up
the holes on the fuel tank flange with holes on the wheel
support frame.
4.4. Place handle on fuel tank flange and line up with the wheel
support frame fixing holes. Insert bolts through the fuel tank
flange and both frames and secure finger tight only with nuts
and washers.
4.5. Repeat with process with the rear handle.
4.6. Attach the cord wraps using screws and nuts.
4.7. When assembly is complete, securely tighten all nuts.
WARNING! DO NOT use the heater without the support
frame fully assembled.
Contents
1 Wheel Support Frame
1 Axle
2 Wheels
1 Front Handle
1 Rear Handle
2 Cord Wraps
2 Axle Bushings
4 Cord Wrap Screws
8 Frame Bolts
8 Frame Nuts
fig.1
© Jack Sealey Limited
Original Language Version
AB1008.V3, AB1258.V3, AB1758.V3 Issue:3 27/11/18
Loading...