INSTRUCTIONS FOR:
ARC WELDERS
MODELS Nos:
140XT.V2
160XT.V2
© Jack Sealey Limited
Original Language Version
140XT.V2, 160XT.V2 Issue: 2 (SP) - 30/04/15
INSTRUCTIONS FOR:
ARC WELDER 140AMP, 160AMP WITH ACCESSORY KIT
MODEL Nos: 140XT.V2, 160XT.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Read Instuctions
Wear Eye Protection
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those
appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a)Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.
To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to
ensure that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and
socket with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
WARNING! Be very cautious if using a generator to power the welder. The generator must be self-regulating and stable with
regard to voltage, wave form and frequency. The output must be greater than the power consumption of the welder. If any of
these requirements is not met the electronics within the welder may be affected.
NOTE: The use of an unregulated generator may be dangerous and will invalidate the warranty on the welder.
WARNING! The welder may produce voltage surges in the mains supply which can damage other sensitive equipment (e.g.
computers). To prevent this happening, it is recommended that the welder is connected to a power supply that does not feed
any sensitive equipment.
1.1.12. *IMPORTANT! IF USING WELDER TO FULL CAPACITY, WE RECOMMEND A 16AMP SUPPLY. WE RECOMMEND YOU
DISCUSS THE INSTALLATION OF A 16AMP INDUSTRIAL ROUND PIN PLUG AND SOCKET WITH YOUR ELECTRICIAN.
Wear A Welders Mask Wear Protective Gloves
Wear Protective Clothing
*
FUSE RATING 13AMP
1.2. GENERAL SAFETY
WARNING! Arc welding produces sparks, fused metal projectiles and fumes which can be dangerous.
WARNING: Unplug from the mains power supply before performing maintenance or service.
Keep the welder and cables in good working order and condition. Take immediate action to repair or replace damaged parts.
Replace or repair damaged parts. Use genuine parts only, unauthorised parts may be dangerous and will invalidate the warranty.
Keep the welder clean for best and safest performance.
Locate welder in a suitable work area. Ensure area has adequate ventilation as welding fumes can be harmful.
Keep work area tidy and free from unrelated materials. Also ensure work area has adequate lighting and a fire extinguisher is at hand.
WARNING: You MUST use an appropriate shaded lens welding face mask (contact your Sealey dealer for details). Permanent eye
damage may result if you do not use correct eye protection. Also wear safety welding gauntlets and dry, oil free safety protective
clothing to protect yourself from sparks and hot droplets of fused metal. Cover exposed flesh to avoid potential burns from the
ultraviolet rays of the arc. Use non-reflective welding curtains to protect other people in the area.
Check you have good ventilation and that air can flow freely around the welder.
DANGER! Ensure no flammable or combustible materials are near work area. Welding containers or pipes which hold, or have held
dangerous gases or substances may explode or burn. Materials cleaned with chlorinated solvents, or varnished surfaces pose danger
of toxic fumes.
Keep unauthorised persons at a safe distance from the work area. Persons within the work area are subject to the same dangers as
the person welding and must take the same precautions.
DO NOT weld on pressurised containers.
Remove ties, watches, rings and other jewellery and contain long hair.
DO NOT use the welder for any purpose other than that for which it is designed.
DO NOT use the welder in damp or wet locations.
DO NOT stand welder on a metal workbench, car bodywork or similar object.
DO NOT touch any live metal parts or the electrode while the machine is switched on.
DO NOT weld without a welding safety head shield, gauntlets and appropriate protective clothing.
DANGER! DO NOT weld near inflammable materials - solids, liquids, or gases.
DO NOT operate welder while under the influence of drugs, alcohol, other medication, or if you are tired.
DO NOT operate the welder if it or the cables are damaged.
DO NOT allow untrained persons to operate the welder.
DO NOT pull welder by the cable, or electrode holder. DO NOT bend or strain cables, protect from sharp or abrasive items. DO NOT
stand on cables or leads. Protect from heat. Long lengths of slack must be gathered and neatly coiled. DO NOT place cables where
they endanger others.
DO NOT touch the electrode holder or workpiece immediately after welding as they will be very hot. Allow to cool.
DO NOT open the cover of the machine. Switch off machine and remove the plug from the power supply after use.
The electromagnetic fields generated by the welding process may interfere with the operation of electrical and electronic equipment.
Users of vital electrical or electronic devices (e.g.pace-makers, respirators etc.) should consult a doctor before entering areas where
welding machines are in use.(see Section 8).
Users of vital electrical or electronic devices should not use any welding machine.
2. INTRODUCTION
Manufactured to exacting standards these models meet all relevant CE requirements. Fitted with forced air cooling system, these welders
have increased duty cycle and performance. All models feature a double vented, wraparound shell fitted to a heavy-duty chassis. Screw type,
stepless welding control allows fine adjustment of current. Each welder is fitted with carry handle. Models supplied with accessory kit including
electrode holder, earth clamp and chipping hammer/wire brush.
This instruction manual contains the information required to prepare your arc welding set for welding. The instructions are not intended to
show you how to become a welder. If you have no experience, we recommend that you seek training from an expert source. Arc welding is
relatively easy to perform, but does require a steady hand and time practising with scrap metal, as it is only with continued practice that you
will achieve the desired results.
3. SPECIFICATION
Model No: .......................................................140XT .V2
Welding Current:................................................45-140A
Electrode Capacity: ....................................Ø1.6-3.2mm
Cooling: ..........................................................Forced Air
Output Cable: ......................................................10mm²
No Load Voltage: ......................................................48V
Absorbed Power: .....................................................3kW
Power Input: ................................................. 230V - 1ph
Weight: ................................................................... 17kg
Max. Permissable System Impedance: .....Zmax(0.22Ω)
Model No: .......................................................160XT .V2
Welding Current:................................................55-160A
Electrode Capacity: ....................................Ø2.0-4.0mm
Cooling: ..........................................................Forced Air
Output Cable: ......................................................16mm²
No Load Voltage: ......................................................50V
Absorbed Power: .....................................................3kW
Power Input: ................................................. 230V - 1ph
Weight: ................................................................... 18kg
Max. Permissable System Impedance: .....Zmax(0.18Ω)
4. CONTENTS
4.1. See Fig.1.
© Jack Sealey Limited
Original Language Version
140XT.V2, 160XT.V2 Issue: 2 (SP) - 30/04/15
© Jack Sealey Limited
Original Language Version
Fig.1
140XT.V2, 160XT.V2 Issue: 2 (SP) - 30/04/15
5. RATINGS PLATE GUIDE
FOR FURTHER CLARIFICATION OF SYMBOLS REFER TO BRITISH STANDARD EN 60974-6
(For actual ratings of your model refer to the top cover)
Fig.2
6. OPERATION
WARNING! If you have no welding experience, we recommend you seek supervised training from an expert source.
6.1. Introduction. Your welder features a single phase transformer with a drooping characteristic suitable for welding with an alternating
current using stick electrodes with diameters from 1.5mm to the highest electrode diameter as shown on the chart in Fig.6.
6.2. Current regulation. The intensity of the welding current can be adjusted by means of a manually operated magnetic shunt. See Fig.1-3.
To increase the current turn the knob clockwise whilst making reference to the graduated scale on the top of the machine (See Fig.3).
To decrease the current turn the knob anti clockwise. Note: Set the current to the desired level before commencing welding.
DO NOT operate the current regulation mechanism whilst welding is in progress.
6.3. Thermostatic Protection.
6.3.1. Temperature Control Indicator Light.
When the machine is overheating, it cuts off the power and the indicator light comes on. When the temperature has dropped to the
recovery temperature, the machine can automatically restart and the indicator light will go off.
See Fig.1-5.
6.3.2 Temperature Protection Indicator Light.
If the Temperature Controller fails, the protector will cut off the power and the indicator light comes on. Temperature protection can not
resume automatically. If needed, please follow the methods below for recovery operations:
1. Turn off the machine's power.
2. Open the cover of the machine.
3. When the temperature protector pops up on the red contacts, such as in the picture right, it means the machine has cut off.
4. Press the red contacts on the thermal protection this means the machine is now in a normal state. As you use larger
welding rods you may experience a temporary current shut off. The larger the welding rod, the greater the current required,
consequently, the hotter the machine will become and the quicker it will cut out.
6.4. Setting up the welder.
6.4.1. Ensure the machine is turned off from the mains power supply. (See fig.1-2).
6.4.2. Attach the earth clamp to a point on the workpiece that has been cleanly ground to provide good contact. Attach it as close as
possible to the area you will be welding.
6.4.3. Select the diameter of electrode to be used in relation to the type of weld to be made. Consideration should be given to the fact that
higher current values should be used for flat welding, whereas for vertical or over head welding lower current values are required.
Insert the electrode into the electrode holder. Ensure there is a good connection. Ensure welding surfaces are kept clean and free
from grease, or oil.
6.4.4. Establish the welding current required in relation to the diameter of electrode you are using by making reference to the table in Fig.6.
6.4.5. Set the current required in amps using the control knob on the front panel. See Fig.1-3. The current set can be read from the
graduated scale on the top of the machine. See Fig.3.
6.5. Commencing Welding It is advisable to practice on scrap metal first, especially where potentially difficult welds are to be undertaken.
WARNING! Remember to wear a full face welding mask, gauntlets and protective clothing and ensure you have read,
understood and apply safety instructions. Wear goggles whilst chipping slag.
6.5.1. DO NOT switch on the power supply until you are fully ready to start welding.
6.5.2. Place the face mask in front of your face.
6.5.3. To strike the arc tap the electrode lightly on the workpiece as if striking a match. DO NOT hit the electrode on workpiece as this may
damage the stick.
© Jack Sealey Limited
Original Language Version
140XT.V2, 160XT.V2 Issue: 2 (SP) - 30/04/15
Fig.4
Fig.3
Fig.5
6.5.4. As soon as the arc is struck maintain a steady gap between the end of the electrode and the workpiece equal to the diameter of the
electrode in use (See Fig.4). Try to maintain this gap continuously through out the duration of the weld. The electrode should also be held
at an angle of 20° to 30° from the vertical. (See Fig.5).
6.5.5. At the end of the weld bead, move the tip of the electrode backwards in order to fill the weld crater. Quickly lift the electrode from the
weld pool to extinguish the arc. Refer to Fig.7 for a welding fault analysis.
6.5.6. If the electrode sticks, you may be holding it too close to the workpiece. Pull sharply to the left, and then to the right to free the
electrode.
6.5.7. After welding, chip off the slag with a chipping hammer. Wear goggles.
6.5.8. Switch off the welder and disconnect it from the mains power supply. Remember that the workpiece and the electrode will still be very
hot.
WARNING! Use pliers to remove the hot consumed electrodes or to move the hot welded pieces.
6.5.9. When welding has finished remove the electrode from the electrode holder as a safety precaution.
Electrode Diameter (mm) Welding Current (Amp)
Min Max
1.6 ..................25.........50
2.0 ..................45.........60
Fig.6
Fig.7
2.5 ..................55........100
3.2 ..................80........140
4.0 ..................85........160
7. MAINTENANCE
WARNING! Ensure the welder is disconnected from the electrical mains power supply before attempting any service or
maintenance tasks outlined below.
7.1. Keep the welder clean and dry at all times. Use a dry cloth to clean the unit.
7.2. Keep all electrodes clean and dry and ensure all cables are in good condition.
7.3. Inspect the welder regularly, with a frequency depending on use and the dustiness of the environment. Remove dust deposits from the
transformer using a jet of dry compressed air, (Max 10bar).
7.4. At the same time make sure that the electrical connections are tight and check the wiring for damage to the insulation.
7.5. If necessary use a very thin layer of high temperature grease, to lubricate the moving parts of the regulators (threaded shaft, sliding
surfaces, shunts etc).
7.6. After these light maintenance operations ensure that the welder covers are replaced and that all fastening screws are fully tightened.
7.7. Use an authorised service agent for any other maintenance or service requirements.
WARNING! Never perform welding operations with the covers removed.
8. COMPATABILITY
8.1. THIS EQUIPMENT IS IN CONFORMITY WITH THE EUROPEAN STANDARD ON THE ELECTROMAGNETIC
COMPATIBILITY OF ARC WELDING EQUIPMENT AND SIMILAR PROCESSES (E.G. ARC AND PLASMA CUTTING)
8.2. Protection against interference (EMC). The emission limits in this standard may not, however, provide full protection against
interference to radio and television reception when the equipment is used closer than 30m to the receiving antenna. In special cases,
when highly susceptible apparatus is being used in close proximity, additional mitigation measures may have to be employed in order
to reduce the electromagnetic emissions. At the same time there could occur some potential difficulties in having electromagnetic
compatibility in a non-industrial environment (e.g. in residential areas). Therefore it is most important that the equipment is used and
installed according to the following instructions.
8.3. Installation and use. The user is responsible for installing and using the equipment according to these instructions. If electromagnetic
disturbances are detected, then it shall be the responsibility of the user of the equipment to resolve the situation with the
technical assistance of the supplier. In some cases this remedial action may be as simple as earthing the circuit (see Note). In
other cases it could involve constructing an electromagnetic screen, enclosing the welding power source and the work, complete with
associated input filters. In all cases the electromagnetic disturbances shall be reduced to the point where they are no longer
troublesome.
Note: The welding/cutting circuit may or may not be earthed for safety reasons. Changing the earthing arrangements should only be
authorised by a person who is competent to assess whether the changes will increase the risk of injury, e.g. by allowing parallel
welding/cutting circuit return paths which may damage the earth circuits of other equipment. Further guidance is given in IEC 974-13
’Arc Welding Equipment - Installation and Use.’
8.4. Assessment of area. Before installing the equipment the user shall make an assessment of potential electromechanical problems in
the surrounding area. The size of the surrounding area to be considered will depend on the structure of the building and other
activities that are taking place. The surrounding area may extend beyond the boundaries of the premises.
The following shall be taken into account :
a) Other supply cables, control cables, signalling and telephone cables, above, below and adjacent to the welding equipment.
b) Radio and television transmitters and receivers.
c) Computer and other control equipment.
d) Safety critical equipment, e.g. security monitoring of industrial equipment.
e) The health of people in the vicinity, e.g. persons fitted with a pacemaker or hearing aid.
f) Equipment used for calibration or measurement.
g) The immunity of other equipment in the environment. The user shall ensure that other equipment being used in the environment is
compatible. This may require additional protective measures.
h) The time of day that welding and other activities are to be carried out.
8.5. Mains supply. The equipment should be connected to the mains supply according to these instructions. If interference occurs, it may
be necessary to take additional precautions such as filtering of the mains supply. Consideration should also be given to shielding the
supply cable of permanently installed equipment in metallic conduit or equivalent. This shielding should be connected to the power
source so that good electrical contact is maintained between the conduit and the welding power source enclosure.
© Jack Sealey Limited
Original Language Version
140XT.V2, 160XT.V2 Issue: 2 (SP) - 30/04/15
8.6. Maintenance of the equipment. The equipment should be routinely maintained according to these instructions. All access and service
covers should be closed and properly fastened when the welding equipment is in operation. The welding equipment should not be
modified in any way except for those changes and adjustments covered in these instructions. In particular, the spark gaps of any arc
striking and stabilising devices should be adjusted and maintained according to the instructions.
8.7. Cables. The welding/cutting cables should be kept as short as possible and should be positioned close together, running at or close
to the floor level.
8.8. Equipotential bonding. Bonding of all metallic components in the welding/cutting installation and adjacent to it should be considered.
However, metallic components bonded to the workpiece will increase the risk that the operator could receive a shock by touching
these metallic components and the electrode at the same time. The operator should be insulated from all such bonded metallic
components.
8.9. Earthing of the workpiece. It is important that the workpiece is separately bonded to earth in addition to the welder/cutter return
cable. Where the workpiece is not bonded to earth for electrical safety reasons or because of its size and position, e.g. ship’s hull or
building steelwork, a connection bonding the workpiece to earth may reduce emissions in some, but not all instances. Care should be
taken to prevent the earthing of the workpiece increasing the risk of injury to others or damage to other electrical equipment.
Where necessary, the connection of the workpiece to earth should be made by a direct connection to the workpiece, but in some
countries where direct connection is not permitted, the bonding should be achieved by a suitable capacitance, selected according to
national regulations.
8.10. Screening and shielding. Selective screening and shielding of other cables and equipment in the surrounding area may alleviate
problems of interference. Screening of the entire welding/cutting installation may be considered for special applications.
9. TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
Power source fuse blown Short circuit in either primary or secondary
transformer windings
Electrode has touched earth clamp Be vigilant to prevent this happening
Wrongly rated fuse Install correct fuse
Welder frequently cuts out The welder is being overworked causing the
thermostatic control to activate
May also be due to a sticking electrode Cut out will automatically reset when welder
Broken fan causing overheating Repair or replace cooling fan
Cooling fan not working properly
Difficulty in striking or maintainig an arc
Starting capacitance disabled Replace capacitior
The electrode is damp Heat it up to 60º - 70º before using
Wrong type of electrode Use correct electrode
Bad connection between earth clamp and
workpiece
Regulation screw and nut worn out Replace worn out parts
Partial short circuit in transformer windings Return to Sealey dealer for assessment/
Noise from within case when welding Uneven gap between the moving iron core
and static iron core
Return to Sealey dealer for assessment/
repair
Cut out will automatically reset when welder
has cooled
has cooled
Grind connection area and reattach clamp
repair
Return to Sealey Dealer to have cores
adjusted
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey Limited
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
01284 757500
01284 703534
140XT.V2, 160XT.V2 Issue: 2 (SP) - 30/04/15
www.sealey.co.uk
sales@sealey.co.uk
Loading...