INSTRUCTIONS FOR
MPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
TROLLEY JACK 2. 25TONNE HIGH LIFT SUPER
ROCKET LIFT
MODEL NO: 1025HL.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
Refer to
instructions
Wear safety
footwear
1. SAFETY
9 Ensure the jack is in sound condition and good working order. Take action for immediate repair
or replacement of damaged parts.
Use genuine parts only. The use of unauthorised parts may be dangerous and will invalidate
the warranty.
9 Locate the jack in a suitable, well lit, work area.
9 Keep work area clean and tidy and free from unrelated materials.
9 Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
9 Place wedges under wheels of vehicle (but ensure wheels of jack can move freely).
9 Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear
(or “Park” if automatic).
9 Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc.,
to allow for vehicle tilting.
9 Ensure there are no passengers in the vehicle.
9 Ensure all non-essential persons keep a safe distance whilst the jack is in use.
9 Only place jack saddle under those lifting points recommended by the vehicle manufacturer
(see vehicle handbook).
9 Check the lifting point is stable and centred on the jack saddle.
9 Ensure the jack wheels are free to move and that there are no obstructions.
WARNING! When lifting at the jack’s maximum rating (2.25tonne/2250kg) or close to it, it
is recommended that the effort of raising the load shall be reduced by the use of assistance
during this operation.
▲ DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
9 Use suitable capacity axle stands under the vehicle before proceeding with any task.
9 Ensure there are no persons or obstructions beneath the vehicle before lowering.
9 Use a qualified person to maintain or repair the jack hydraulic system.
8 DO NOT operate the jack if damaged.
8 DO NOT allow untrained persons to operate the jack.
8 DO NOT exceed the rated capacity of the jack.
8 DO NOT allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.
8 DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
8 DO NOT work under the vehicle until axle stands have been correctly positioned.
8 DO NOT use the jack for purposes other than that for which it is intended.
8 DO NOT top up hydraulic system with brake fluid. Use hydraulic jack oil only.
8 DO NOT adjust the safety overload valve.
9 When not in use store jack, fully lowered, in a safe, dry, childproof area.
2. INTRODUCTION
Ideal for the garage or serious enthusiast. Suitable for 4x4s, cars or light commercial vehicles which require high ground clearance.
Super Rocket Lift feature brings lifting arm into contact with jacking point in minimal strokes. Strong double rolled chassis. Also
suitable for loading bodyshop chassis jigs.
3. SPECIFICATION
Model no: .................................................................1025HL.V3
Capacity ......................................................2.25T onne/2250kg
Min. saddle height .........................................................150mm
Max. saddle height ........................................................535mm
Max chassis height ........................................................180mm
Length ...........................................................................720mm
Weight ............................................................................21.5kg
© Jack Sealey Limited
Original Language Version
1025HL.V3 | Issue 2 (1, F) 19/06/18
4. OPERATION
4.1. Beforerstuse.
4.1.1. Before using jack for the first time, purge the hydraulic unit in order to eliminate any air in the system. Place handle onto the release
valve, fig.1.B and open valve by turning the handle anti-clockwise for a maximum of one turn. Place handle back into the jacking
point, fig1.A and pump for 30 to 40 seconds. When complete, close the release valve by turning the valve fig.1.B clockwise.
4.1.2. Place a few drops of hydraulic jack oil on pump piston. Pump handle several times to distribute oil. Thoroughly lubricate moving
parts.
4.2. General jacking.
WARNING! When lifting at the jack’s maximum rating (2.25tonne/2250kg) or close to it, it is recommended that the effort of raising the
load shall be reduced by the use of assistance during this operation.
WARNING! Before lifting ensure Section 1 safety instructions are read and understood.
4.2.1. Prepare the vehicle as mentioned in the safety instructions ensuring the ground on which the jack is to stand is level and solid (not
tarmacadam).
4.2.2. Position the jack saddle under the vehicle manufacturer’s recommended lifting point.
4.3. Jacking the vehicle.
4.3.1. Place the handle onto the release valve fig.1.B and turn it clockwise to close the valve. Place handle into socket fig.1.A and
commence pumping handle up and down, until the jack saddle reaches the vehicle jacking point. Check the jacking point is centrally
located on the saddle. Super Rocket Lift will only operate until chassis is reached. After that continued pumping raises the load at a
slower rate.
Note: Maximum height can only be obtained if the jack is sufficiently loaded.
4.3.2. Should the jack become overloaded, a safety excess pressure valve will open, and stop the vehicle from lifting.
WARNING! The jack is a lifting device only and must not be used to support the load. Use correctly rated axle stands to support the
load.
4.4. Lowering the vehicle.
4.4.1. If using axle stands, raise the jack high enough for the stands to be easily removed. Then place handle on release valve fig.1.B and
turn anti-clockwise, very slowly, to open the valve.
4.4.2. The lowering speed is controlled by the amount you turn the handle. Lower carefully, avoid any sudden changes in descent rate which
would shock load the hydraulic system.
WARNING! Ensure there are no persons or obstacles beneath the vehicle, or in the path of its descent.
g.1
5. MAINTENANCE
5.1. When the jack is not in use, the ram should be in its lowest position to minimise corrosion. Remove the handle to inactivate jack.
5.2. Keep the jack clean and lubricate all moving parts with oil on a regular basis.
5.3. Before each use check for broken, cracked, bent, or loose parts, or any visible damage to ram, pump, saddle, lifting arm, frame and all
parts including nuts, bolts, pins and other fasteners. If any suspect item is found remove jack from service and take necessary action
to remedy the problem.
8 DO NOT use the jack if believed to have been subjected to abnormal load or shock load.
5.4. Periodically check the pump piston and the ram for signs of corrosion. Clean exposed areas with a clean oiled cloth.
8 After one year the oil should be replaced in order to extend the life of the jack. Use hydraulic jack oil only.
IMPORTANT: Only fully qualified personnel should attempt hydraulic maintenance or repair.
5.5. To check the oil level, fully lower the jack. Remove filler plug fig.1.O. The correct level is the bottom of the screw hole. If oil level is low,
fill as required. Pump jack 5 or 6 times to expel air. Pump jack up to full height and pour off excess oil before refitting plug.
8 DO NOT touch the safety overload valve (fig.1.V),
NOTE: Use a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL.
WARNING: DO NOT use brake fluid, or any fluid other than hydraulic jack oil as this may cause serious damage to the jack and will
invalidate the warranty!
5.6. To drain the oil, remove the filler plug and raise front of jack. Make sure that no dirt is allowed to enter the hydraulic system.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THIS PRODUCT.
Owing to their size and weight, hydraulic products should ideally be repaired by local service agents. We have service/repair agents
in most parts of the UK. Before returning your product please telephone our technical help line on 01284 7575505 for advice and
trouble shooting guidance..
If jack is under guarantee contact your local Sealey stockist.
De-commissioning the Jack
Should the jack become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of
the jack and the oil according to local regulations.
© Jack Sealey Limited
Original Language Version
1025HL.V3 | Issue 2 (1, F) 19/06/18
Loading...