Sealer Sales WN-750H, WN-650H, WN-650HC, WN-750HC, WN-1000HC User Manual
...
Long Hand Sealer
Models: WN-500H/HC, WN-650H/HC, WN-750H/HC, WN900H/HC,
WN-1000H/HC, WN-1300H, WN-1500H/HC
Distributed By:
Version 1.3
Last Updated: 4/23/2019
Copyright © 2015 by Stephanie Hwang
All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying,
recording, or other electronic or mechanical methods, without the prior written permission of the publisher, except in the case of brief quotations
embodied in critical reviews and certain other noncommercial uses permitted by copyright law. For permission requests, write to the publisher,
addressed “Attention: Permissions Coordinator,” at the address below.
Sealer Sales, Inc.
8820 Baird Avenue
Northridge, Ca 91324
www.sealersales.com
Printed in the United States of America
1
W H L H I N S T R U C T I O N M A N U A L
2
WHLH E Q U I P M E N T I N F O R M A T I O N
Model #
Serial #
Purchase Date:
Reference # (found on packing slip)
Owner:
General Information
Thank you for purchasing our W-Series Long Hand Sealers.
This owner’s manual contains information relating to your sealer. The manual will provide you
with basic information concerning both operation and maintenance of your new machine. Please
read it carefully as failure to do so may result in bodily injury and/or damage to the equipment.
Please fill in the information below. You will find the information on the machine identification
plate. You will need this information when ordering replacement parts or making technical
inquiries.
No part of this manual may be duplicated, reproduced, stored in a retrieval system, translated,
transcribed, or transmitted in any form without the express prior written permission of Sealer Sales.
W H L H I N S T R U C T I O N M A N U A L
3
Safety Instructions
WARNING!
Below are general safety precautions and warnings that should be
understood prior to setting up or operating your equipment. Read and fully understand all instructions and
warnings prior to using this unit. Your safety is most important! Failure to comply with procedures may
result in serious injury or property damage. Remember:
responsibility.
Unsafe practices or unauthorized modifications could result in accidents or property damage. Failure to
follow these safety rules and take necessary precautions can result in serious injury as well as damage to
equipment. Failure to comply with the safety instructions would also void the warranty.
Never operate or service your sealer until you have read this manual completely and understand it
fully.
Only plug the sealer into a standard 120 Volt, 60Hz wall outlet or surge protector.
Do not use the sealer if the power cord, plug or any other parts are damaged. Do not to allow the
power cord to drape into your work area. Check that all parts are operating properly and perform
the intended functions. Check for any worn parts before starting operation. Check for all other
conditions that may affect the operation of your sealer.
Reduce risk of unintentional starting. Make sure the power switch is in the "OFF" position before
attaching to the power source.
Your personal safety is your
Always disconnect sealer from power source before servicing, changing accessories or cleaning the
unit.
To provide protection against the risk of electrical shock, the power connection must be properly
grounded at all times.
Do not leave the sealer unattended when in use. Disconnect the sealer from the power source
before leaving the work area.
Do not use the machine for any other purpose other than to seal thermoplastic materials. Doing
so may result in damage to the machine and injury to the operator.
While operating machinery, wear close-fitting clothing and tie back long hair to prevent any
external items from getting caught in the machine. Do not wear jewelry when operating the sealer.
W H L H I N S T R U C T I O N M A N U A L
4
Never touch the heating elements with hand while the sealer is plugged into a power source, in
operation or just finished operation. Touching heated areas may cause fire and/or severe burns.
The blade found on the Long Hand Sealer w/ Cutter is very sharp. Use
extreme caution when handling or changing the blade.
While machine is in operation, do not place fingers, tools, or other foreign objects on or into the
machine. Do not place hands or fingers near pinch points. Do not touch machine while it is in
operation. Perform all procedures carefully and watch where hands and fingers are at all times.
The sealer is not water resistant or water proof. Spraying down the machine will damage machine
or cause electrical shock. Do not submerge the sealer into water or liquid.
Do not operate sealer in a corrosive or humid environment.
Always keep the machine clean and in good working condition. Follow any maintenance
procedures outlined in this manual. Make sure unit is disconnected from power source before
cleaning.
NEVER use any accessories or parts from other manufacturers. Machine should not be altered or
modified using parts that are not genuine authorized parts. Doing so will VOID YOUR
WARRANTY.
When replacing the heating elements, always replace the PTFE adhesive under the
heating element. A worn PTFE adhesive can cause the heating element to break.
The
PTFE adhesive works as a barrier between the body of the sealer and the element. Never allow
the element to come in direct contact with the sealer body as that will damage the timer.
Never leave the sealer unattended. Be safe, disconnect the sealer from power source before
leaving work area.
Always keep out of reach of children and pets.
Close supervision is necessary when any appliance is near persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge . This sealer is NOT to be used by
children or by persons with reduced physical, sensory or mental capabilities or lack of experience
and knowledge.
Do NOT use the sealer outdoors.
Do NOT use the sealer while under the influence of drugs, medications or alcohol.
SAVE THESE INSTRUCTIONS - REFER TO THEM OFTEN AND USE THEM
TO INSTRUCT OTHERS.
W H L H I N S T R U C T I O N M A N U A L
5
WN-500H
WN-500HC
WN-650H
WN-650HC
WN-750H
WN-750HC
WN-1000H
WN-1000HC
WN-1300H
WN-1500H
WN-1500HC
Power
110V/60Hz
or
220V/50Hz
110V/60Hz
or
220V/50Hz
110V/60Hz
110V/60Hz
110V/60Hz
110V/60Hz
Watts
600W
800W
1000W
1400W
2000W
2500W
Seal Width
2.7mm
2.7mm
2.7mm
2.7mm
2.7mm
2.7mm
Sealing Length
19 3/4"
25 3/4"
29 3/4"
39 3/4"
51 3/16"
59"
Cutting Length
18 3/4"
24 3/4"
28 3/4"
38 3/4"
N/A
58"
Dimensions
28" x 5" x 10"
34" x 5" x 10"
38" x 5" x 10"
48" x 5" x 10"
63" x 5" x 13"
75" x 5" x 14"
Shipping
Dimensions
33" x 10" 15"
39" x 10" x 15"
42" x 10" x 15"
53" x 10" x 16"
64" x 11" x 14"
82" x 16" x 15"
Net Weight
21lbs
26lbs
27lbs
33lbs
40lbs
79lbs
Gross Weight
36lbs
30lbs
32lbs
40lbs
42lbs
93lbs
Basic
Principles
Place material on lower
jaw and bring sealing
arm to activate sealing
process
Introduction
W-Series Long Hand sealers are designed for sealing longer materials for specialized sealing needs. Our
W-Series Long Hand sealers w/ cutters are accompanied with a sliding cutter ideal for sealing or making
bags from poly tubing. The sealers can seal polyethylene, polypropylene, saran, nylon, static shielding
bags, and Mylar up to 10mil in total thickness.
Features of the W-Series Long Hand Sealers
Your Long Hand sealer is equipped with a wide range of standard features and capabilities.
Impulse sealing - no warm up time needed
Electronic timer for variable control
Heavy duty all metal construction
Table top design supported with anti-slip rubber feet
Seal width: 2.7mm wide flat heating element
Option: Round heating elements available for seal and cut applications
Manufacturer spare parts kit includes: 3 heating elements and blade (cutter version only)
How Do W-Series Long Hand Sealers Work?
Our W-Series impulse sealers fire a short burst of electricity through a specially
designed heating wire to weld thermoplastic materials together. The length of the
seal time will depend on the sealing characteristics of the bag being sealed. The
sealing process is simple: The operator places material on the base of the sealer
and brings the sealing arm down to seal.
Specifications
Loading...