Seagate ST650211CF, ST625211CF, ST625211FX, ST650211FX User Manual

0 (0)
Seagate ST650211CF, ST625211CF, ST625211FX, ST650211FX User Manual

ST1 Series Installation Guide

ST650211CF, ST650211FX, ST625211CF, and ST625211FX

CompactFlash Interface Disc Drives

Publication Number: 100325579, Rev. C, May 2005

The easiest way to install your ST1 Series drive

Many of today’s consumer products, like cameras, notebook computers, MP3 players, printers and more have been designed to make it possible for the end user to use compact flash interface devices. Your Seagate ST1 Series drive is designed for such use. Refer to your product’s user manual for the location of the compact flash media compartment and the specific instructions regarding insertion and removal of removable media devices like the ST650211CF and ST625211CF models. Your product’s manufacturer’s support website will have the most up-to-date information. Read and follow all instructions regarding the proper steps to be taken when using your Seagate ST1 Series disc drive.

The Seagate ST1 Series Flex interface disc drive models, ST650211FX and ST625211FX, are designed for embedded installation, or as a fixed storage solution. Follow the installation instructions provided on this instruction sheet. Your product’s manufacturer’s support website will have the most up-to-date information on installing and removing storage devices. Read and follow all instructions regarding the proper steps to be taken when using your Seagate ST1 Series disc drive. It is important to follow the handling precautions and electrostatic discharge protection information below when handling any electronic device. It is always a good idea to back up all your data before installing any new hardware in your computer.

Handling precautions/electrostatic discharge protection

ST1 Series disc drives are fragile. Do not drop or jar the drive. Handle the drive only by the edges or by the finger grip area shown in Figure 1. Keep the device in the packaging until you are ready to install it and between uses to minimize handling damage.

It may be necessary to turn off the power to the host product during installation. Refer to your product’s user manual for details regarding installation and removal of media devices.

Do not disassemble the drive. Doing so voids the warranty. See the warranty information on page 2.

Do not expose the drive to extreme temperatures or humidity conditions.

Do not apply pressure, write on, or attach labels to the top or bottom of the drive.

Do not cover or otherwise obstruct the breather hole on the top of the drive. (See Figure 2 and Figure 3)

Keep the drive away from strong magnetic fields to avoid data loss.

Figure 1 ST1 Series - Finger grip areas

Drive characteristics

 

ST650211CF

ST625211CF

Formatted capacity

5.0 Gbytes

2.5 Gbytes

Total number of sectors*

9,767,520

4,883,760

Cache size

2 Mbytes

2 Mbytes

 

ST650211FX

ST625211FX

Formatted capacity

5.0 Gbytes

2.5 Gbytes

Total number of sectors*

9,767,520

4,883,760

Cache size

2 Mbytes

2 Mbytes

*One sector equals 512 bytes.

Note. The Seagate ST1 Series CompactFlash disc drive is compatible with the CF+ and CompactFlash Specification 2.0.

Note. The Seagate ST1 Series Flex interface disc drive is compatible with the ATA version 7.

Installing your ST1 Series CompactFlash model disc drive

Each product, which utilizes CompactFlash storage devices, has its own unique removable media compartment. Refer to the product’s user manual to locate the media compartment and for instructions on removing and installing media devices.

Warning. It may be necessary to turn off the product. Refer to your product’s operator manual for cautions, warnings and recommendations on the installation and removal of media devices.

Note. This drive is designed for a product that supplies interface signals and +3.3V power through the compact flash connector. Refer to your consumer products manual to determine if your Seagate ST1 Series disc drive is compatible. See Figure 2 for drive dimensions.

 

 

Recommended case

 

G

temp. measurement location

FINGER GRIP

 

 

 

 

 

F

Breather Hole

 

Do not cover

 

E

 

B

Bottom View

D

 

C

 

Bottom

 

 

 

N

A

 

 

 

 

 

 

 

 

J

 

 

 

 

 

H

 

 

 

 

 

K

L

Top

 

 

 

 

 

 

 

 

M

 

 

 

 

 

 

 

Pin 1

Pin 50

 

 

 

 

 

 

 

Figure 2 ST1 Series - CF+ dimensions—end, top, and side views.

CF Dimension Table

FX Dimension Table

 

Inches

 

Millimeters

A

0.197

± .004

 

5.00

± .10

B

1.433

± .006

 

36.40

± .15

C

1.685

± .004

 

42.80

± .10

D

1.015

± .003

2x

25.78

± .07

E

1.152

± .010

 

29.25

± .25

F

0.299

± .010

 

7.61

± .25

G

0.394

min

 

10.00

min

H

0.063

± .002

 

1.60

± .05

J

0.040

± .003

2x

1.01

± .07

K

0.039

± .002

 

1.00

± .05

L

0.039

± .004

2x

1.00

min

M

0.065

± .004

 

1.65

± .10

N

0.243

± .004

2x

6.16

± .10

FINGER GRIP

G

 

Breather Hole

Do not cover

E

Bottom View

 

Inches

 

Millimeters

A

0.197

± .004

 

5.00

± .10

B

1.433

± .006

 

36.40

± .15

C

1.685

± .004

 

42.80

± .10

D

1.015

± .003

2x 25.78

± .07

E

1.152

± .010

 

29.25

± .25

F

0.299

± .010

 

7.61

± .25

G

0.394

min

 

10.00

min

H

0.063

± .002

 

1.60

± .05

J

0.040

± .003

2x

1.01

± .07

K

0.039

± .002

 

1.00

± .05

L

0.039

± .004

2x

1.00

min

M

0.065

± .004

 

1.65

± .10

P

0.906

± .003

 

23.00

± .07

R

0.669

± .020

 

17.00

± .50

S

0.414

± .020

 

10.51

± .50

T

0.130

± .004

2X

3.30

± .10

Recommended case temp. measurement location

A

F

B

D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R

 

 

 

 

 

Pin 45

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin 1

 

 

 

 

 

 

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P

 

 

 

 

 

 

 

 

 

T

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bottom

 

 

 

 

 

 

 

K

 

 

 

H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Top

L

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

M

 

Figure 3 ST1 Series - FX dimensions—end, top, and side views

Loading...
+ 1 hidden pages