Seagate ST3620N-ND-NC, ST31200N-ND-NC User Manual

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HAWK 1LP Family:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ST31200N/ND/NC

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ST3620N/ND/NC

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation Guide

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents

Introduction........................................................... 1

Electromagnetic interference ................................ 1

Before you begin .................................................. 3

Installation overview ............................................. 8

Product Repair...................................................... 10

Shipping ......................................................... 11

Product Repair and return information ........... 11

Technical support services...................................12

Hawk 1LP family product information ................... 15

Initial set-up information........................................ 17

Drive configuration................................................ 22

Drive installation ...................................................32

Seagate®, Seagate Technology® and the Seagate logo are registered trademarks of Seagate Technology, Inc. HawkTM, SeaFAXTM, SeaFONETM, SeaTDDTM, and SeaBOARDTM, are trademarks of Seagate Technology, Inc. Other product names are registered trademarks or trademarks of their own.

Seagate reserves the right to change, without notice, product offerings or specifications. No part of this publication may be reproduced in any form without written permission of Seagate Technology, Inc.

Hawk 1LP Family Installation Guide, Rev. D 1

Introduction

This manual is organized to assist you in the installation and operation of your Seagate Hawk 1LP Family disc drive. Family models are listed in Hawk 1LP Family Product Information section. It also provides information to aid in obtaining service for the drive.

Before attempting any installation, please read through all applicable sections of this document, including all warnings and cautions.

Warning.

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with these instructions, may cause interference to radio communications.

Electromagnetic interference (EMI) considerations

The drive(s) described herein, as delivered, are designed for system integration and installation into a suitable enclosure prior to use. As such, the drive(s) described herein are supplied as a sub-assembly and are not subject to Subpart J of Part 15 of the FCC Rules

2 Hawk 1LP Family Installation Guide, Rev. D and Regulations nor the Radio Interference Regula-

tions of the Canadian Department of Communications. However, the unit has been tested using proper shielding and grounding and found to be compliant with the Class A limits of the FCC Rules and the Regulations of the Canadian Department of Communications.

The physical design characteristics of the drive(s) described herein, serve to minimize EMI radiation when installed in an enclosure that provides reasonable shielding. As such, the drive(s) are capable of meeting the Class B limits of the FCC Rules and the Regulations of the Canadian Department of Communications.

Note. It is the end users' responsibility to assure that

the drive(s) described herein meet the appropriate EMI requirements of their system. Shielded I/O cables may be required if the enclosure does not provide adequate shielding. If I/O cables are external to the enclosure, shielded cables should be used, with the shields grounded to the enclosure and to the host controller.

Hawk 1LP Family Installation Guide, Rev. D 3

Before you begin

Verify that the system is switched off and disconnected from main power before any installation is attempted.

Protect yourself, the drive, and your valuable programs and data by reading the following cautions and warnings.

• Do not tamper with sealed top cover. Doing so voids your warranty. The drive contains no user serviceable components. See Product Repair section for more information.

• Visually inspect the shipping container for any obvious damage.

• Verify all parts listed on shipping bill are received with the equipment. Discrepancies or damage should be reported to the shipping company.

• Inspect drive for possible shipping damage. All claims of this type should be filed promptly with the transporter involved. Save original packing materials to be used when reshipping.

4 Hawk 1LP Family Installation Guide, Rev. D

• When transporting or shipping a drive or system, please ensure that they are correctly packed in original Seagate approved (or equivalent) container and shipped via an air-ride carrier experienced in handling computer equipment.

• Do not unpack drive from its static shielded bag until you are ready to install it in the system.

• Always handle the drive by the frame or casting.

• Do not touch Printed Circuit Board (PCB) or the I/O connector pins.

• Never apply pressure to the PCB or to the drive top cover

Caution. The circuit assemblies and components

contained in this equipment can be degraded or destroyed by Electrostatic Overstress (EOS) or by Electrostatic Discharge (ESD).

Hawk 1LP Family Installation Guide, Rev. D 5

Static electrical charges can accumulate quickly on personnel, clothing and synthetic materials. The electrostatic fields due to these charges when brought in close proximity to susceptible circuit assemblies and components, can result in degraded reliability or immediate failure of the affected component or assembly.

To insure optimum reliable equipment operation, it is required that technical support personnel discharge themselves by wearing a grounding strap around the wrist and be connected to a grounding terminal while working in the vicinity of, and while handling EOS/ESD susceptible assemblies/parts. If unavailable, ground yourself frequently by touching the metal chassis of the system before handling any components (this helps only if the system is connected to a ground).

Avoid static-inducing carpeted areas.

procedure is especially important when handling printed circuit boards (PCB's).

This

6 Hawk 1LP Family Installation Guide, Rev. D

Safety instructions

1. The disc drive(s) are to be installed in a customer

supplied enclosure where the surrounding air does not exceed 50oC.

2. Four (4) 6-32 UNC-2A screws are required for

installation. Maximum screw length into side of drive is 0.15 inches (3.81 mm). Maximum screw length into bottom is 0.20 in. (5.08 mm). Screw tightening torques is 8.0 lb-in (.90 NM) max with minimum thread engagement of 0.12 in (3.00 mm).

3. The power requirements are shown in the Product

Information section.

4. The power supply must satisfy the safety require-

ments for SELV (Safety Extra Low Voltage) circuits.

5. Service is to be provided by trained Seagate ser-

vice personnel.

6. The incorporation of the disc drives listed in this

guide into a customer enclosure must meet the appropriate safety requirements of the country in which it is used (e.g. UL 1950, CAN/CSA-C22.2 No. 950-M89, DIN VDE 0805/05.90 and EN60950: 1988 (IEC 950).

Note

Power must be off when connecting or disconnecting.

Hawk 1LP Family Installation Guide, Rev. D 7

Sicherheitsanleitung

1. Däs Gerät ist ein Einbaugerät, vorgesehen für eine maximale Umgebungstemperatur von 50oC.

2. Zur Befestigung der Drive werden 4 Schrauben benötigt (6-32 UNC-2A). Die maximale Länge der Schrauben in der unteren Seite des Chassis darf nicht mehr als 0.20 in (5.08 mm) betragen, die in der oberen 0.15 in (3.81 mm). Maximalle Schraubenanziehung von 8.0 in-lb (.90 NM) mit minimalem Gewindeansperuch .12 in (3.00 mm).

3. Die Versorgungsspannungen werden in der Sektion Produkt Information gezeigt.

4. Die Versorgungsspannung muss SELV entsprechen.

5. Alle Arbeiten dürfen nur von ausgebildetem Seagate Service-Personal durchgefürhrt werden.

6. Der Einbau des Drives muss den Anforderungen gemäss DIN VDE 0805/05.90 oder EN60950: 1988 (IEC 950).

Vorsicht

Ánsehluss oder Entfernung oler Geräteverbindung nur bei abgeschalteter Versorgungsspannung vornehmen.

8 Hawk 1LP Family Installation Guide, Rev. D

Installation Overview

Installation of the drive can be divided into distinct phases. Some of these may not be applicable to all system installation requirements. Refer to the individual drive installation sections for specific information on your drive model.

• Drive configuration: Select those drive features that are appropriate to install the drive in the system. This is done by installing or removing user configuration jumpers found on the drive PCB.

• Mechanical installation: After setting up the drive configuration the drive must be mechanically installed into the host system and the power and I/O cables attached. Previously mentioned precautions should be observed.

• CMOS configuration: SCSI drives should not be defined in the CMOS. The SCSI host adapter uses its own BIOS to handle the Input/Output procedures. The CMOS setting for SCSI drive is either drive type zero, or the no drive installed option.

Hawk 1LP Family Installation Guide, Rev. D 9

• Low-Level formatting: All Hawk 1LP family drive models are low-level formatted at the factory and do not require this step during installation. If an installed drive is low-level formatted, all user data will be lost.

Note: Seagate Technology assumes no liability for lost

user data.

• Partitioning and high level formatting: A drive can be sub-divided into "partitions" which behave as individual drives within the system. Consult the system documentation for instructions on partitioning and high level formatting. Information is also available in bookstores and libraries.

10 Hawk 1LP Family Installation Guide, Rev. D

Product repair information

Service requirements The special facilities required for the manufacture of

these drives generally prohibit repair in the field. If problems occur during installation, please contact your supplier for assistance. Do not attempt to disassemble or repair. Drives should be sent to the repair depot through the purchase source, if possible. Please observe the following cautions.

Caution.

• Handle drive with care. Do not drop, or bump hard.

• Never remove the cover of these disc drives. Servicing items in the sealed HDA (heads, media, actuator, etc.) require special facilities. The drive contains no user purchasable parts or PCBs.

• Opening the sealed HDA voids the drive warranty.

• Applying a soldering device to the components on the PCB voids the drive warranty.

• Do not connect or disconnect cables without first removing power from the drive.

+ 28 hidden pages