Seagate ST336807LW-LC User Manual

Cheetah 10K.7 36GB SCSI Installation Guide

ST336807LW/LC

Publication Number: 100358431, Rev. A, November 2004

Handling precautions/Electrostatic discharge protection

• Disc drives are fragile. Do not drop or jar the drive. Handle the drive only by the edges or frame.

• Drive electronics are extremely sensitive to static electricity. Keep the drive in its antistatic container until you are ready to install it. Wear a wrist strap and cable connected to ground. Discharge static from all items near or that will contact the drive. Never use an ohmmeter on any circuit boards.

• Turn off the power to the host system during installation.

• Always use forced-air ventilation when operating the drive.

• Use caution when troubleshooting a unit that has voltages present.

• Do not disassemble the drive; doing so voids the warranty.

• Return the entire drive for depot service if any part is defective.

• Do not apply pressure or attach labels to the drive.

Electromagnetic compliance

See Safety and Regulatory Agency Specifications, p/n 75789512.

Drive characteristics

ST336807 LW/LC

Formatted capacity 36 Gbytes Total # of data blocks (512 byte sector size) 71,687,372 (445DCCCh) Cylinders (user accessible) 90,774 Heads (user accessible) 1 Disc rotation ± 5% 10,000 RPM Operating voltages +5V +12V

Typical operating current (amps) 0.60 0.72

What you need

• Screwdriver and four 6-32 UNC drive mounting screws

• Forced-air ventilation to provide adequate drive cooling

• An unused drive power connector (not applicable to LC models)

To operate at LVD transfer rates, you may also need an LVD-capable SCSI host adapter, LVD I/O cable and active negation external terminator.

Multimode interface

This drive can operate in single-ended (SE) or low voltage differential (LVD) mode. This multimode capability provides backwards compatibility so you can use it with or without an LVD-capable host adapter. The primary benefits of LVD technology include faster transfer rates, increased allowable cable lengths, and improved device connectivity.

You can configure the drive to detect between SE and LVD modes automatically or force it to operate in SE mode only. To configure this option, see Figure 2.

Note. To operate at Ultra2 rates or faster in LVD mode, all devices on the

same bus (cable) must be running in LVD mode. If you add any SE device to the bus, all devices on that bus operate in SE mode.

Note. Some LVD host adapters provide an LVD connector and an SE con-

nector on the same host adapter to allow you to run SE and LVD drives concurrently at their maximum capabilities. Check your SCSI host adapter documentation. See Figure 3.

Caution. Do not mix LVD drives on the same bus with high voltage differ-

ential (HVD) devices—drive damage may occur.

Installation instructions

1. Set the SCSI ID

Determine which SCSI IDs are already being used in t he system and then assign this disc drive a SCSI ID that isn’t already being used. Use the J6 connector located on the front of the drive to set the SCSI ID (see Figure 1).

• Most Cheetah this is the only SCSI drive in your system and there are no other SCSI devices on the daisychain, you can leave this drive’s SCSI ID set to 0 and proceed to the next step.

10K.7 drives are factory set with the SCSI ID set at 0. If

• The host system’s SCSI controller usually uses SCSI ID 7.

• If you have an LC model drive, t he host norm ally s e ts the ID over the I/O interface, so you don’t need to worry about this step.

• If you have an LW model drive, some systems provide a cable designed to connect to the J5 jumper block on the drive to remotely set the ID. You can connect this cable to J5 and use the host-provided remote switch to set the SCSI ID. This J5 connector is not present on LC model drives.

Drive Front

Jumper Plug

(enlarged to show detail)

Reserved

A2A1A0A

SCSI ID = 0 (default) SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 SCSI ID = 8 SCSI ID = 9 SCSI ID = 10 SCSI ID = 11 SCSI ID = 12 SCSI ID = 13 SCSI ID = 14 SCSI ID = 15

Pin 1

68 Pin

SCSI I/O

Connector

SCSI ID = 0 SCSI ID = 1 SCSI ID = 2

SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 SCSI ID = 8

SCSI ID = 9 SCSI ID = 10 SCSI ID = 11 SCSI ID = 12 SCSI ID = 13 SCSI ID = 14 SCSI ID = 15

Pin 1

not used

+5V

Ground

3A2A1

Drive HD

Pin 1

DC Power

4P 3P 2P 1P

(default)

Rear

PCB

Figure 1. Setting the SCSI ID (the J5 block is on LW models only)

2. Configure terminat ion

If you are installing the drive in a system that has other SCSI devices installed, terminate only the end devices on the SCSI bus (cable). This drive does not have internal terminators or any other way of adding internal termination on the drive. You must provide external termination when termination is required. This is normally done by adding an inline terminator on the end of the cable. See Figure 3 for an illustration showing a system configuration that uses an external terminator.

• Use active (ANSI SCSI-2 Alternative 2) single-ended terminators when terminating a bus operating in single-ended mode.

• Use SPI-2-compliant active low voltage differential terminators when terminating a SCSI Ultra2 bus operating in LVD mode.

• The host adapter is normally on the end of the bus and internally terminated. You can configure your bus with another device on the end if you remove termination from the host adapter.

3. Configure terminat or power (LW mode l only)

Term inator s have to get power from some source. The default configuration results in the drive not supplying termination power to the bus. You should normally leave this drive set at this default unless your host system requires the drive to supply termination power to the bus. To configure this drive to supply termination power to the bus, place a jumper on J2 (LW model only) pins 1 and 2 as shown in Figure 2.

4. Connect the drive activity LED (optional)

Connect the Drive Activity LED cable to J6 pins 1 1 and 12 (see Figure 2), or connect a drive ID and Drive Activity LED cable to J5, depending on host system requirements.

5. Check the other available jumper settings

Select other options on J2 (LW model only) as illustrated in Figure 2. Do not change these unless instructed to do so by the host system documentation.

Drive with HDA up, PCB down, viewed

from front

Reserved

Remote LED

Shipped with cover installed.

Do not remove.

Do not install jumpers

on these four positions.

Drive Front

DC Power Connector

SCSI I/O

Connector

HDA

L E D

Pin 1

A2A3A1A

Pin 1

End

Pin 1

J6 Jumper

J2 Jumper

R E S

Reserved Positions

Delay Motor Start option (valid only if the Enable Motor Start jumper is not connected)

Disable the Delay Motor Start option.

Motor start delay equal to the SCSI ID multiplied by 12 seconds.

Motor Start option

CATH

Disable motor start (default). The drive starts according to the Delay Motor Start option.

Enable motor start. The drive waits for the Start Unit command from the host before starting the spindle motor.

Write Protect option

Write protect = Off (enables writing).

Write protect = On (disables writing).

Parity Check option

Enable parity check of SCSI bus.

Disable parity check.

Single-ended I/O A jumper here forces single-ended

I/O operation.

No jumper allows host to select either single-ended or LVD operation.

Terminator Power

Term. Power to SCSI Bus Host adapter or other device provides

term. power to external terminator.

Figure 2. Option select jumpers (LW model only)

6. Mount the drive in the host system and connect cables Note. LC drives are designed to be attached to a carrier or tray and

inserted into the host system without I/O or power cables.

a. Mount LW model drives to the host system’s chassis using four 6-32

UNC screws. Two mounting holes are in each side of the drive and there are four mounting holes in the bottom of the drive. Do not overtighten or force the screws. You can mount the drive in any orientation.

b. Connect the SCSI I/O cable into the drive’s SCSI connector. Take care

not to stretch or crimp this cable, and do not block the system’s cooling air flow with the cable.

Note. For Ultra2 and faster operation, special twisted pair LVD cables are

required.

c. Connect the DC power cable to the drive. See Figure 3.

Ultra160 or Ultra2 LVD bus segment

Pin 1

(check your

adapter for

Pin 1 location)

SCSI LVD/SE

CSI SE

Twisted Pair

LVD Cable

Host

Adapter

PCB

Ultra SCSI SE bus segment

Figure 3. Cable connections and external termination

7. Format the drive

The drive has been low level formatted at the factory. You do not need to perform another low level format on this drive unless you decide to perform certain diagnostics through the host adapter. If you do decide to perform a low level format, do not abort the format as this is likely t o make the drive inoperable. A low level format, with verify turned on, will typically take two hours.

Protect against power failure or other power interruptions during the format. a. Turn on DC power to the host system.

b. Boot the system from a system floppy, CD, or from a previously

installed hard disc drive if there is one.

c. Format the drive. Caution. Formatting a drive erases all user data. Be sure that you under-

stand this principle before formatting any hard disc drive. It is not

Pin 1

(default)

SPI-2 compliant active LVD external terminat on the end of the cable

necessary to format a drive that previously has been used to store data, unless your intention is to erase all user data.

Seagate

is not responsible for lost user data.

Cheetah 10K.7 disc drives are designed to operate with a variety of operating systems. Please refer to your system or SCSI controller manual for information about formatting and setting up the drive. Some quick desktop system notes are provided below.

• Microsoft

. Set the drive type in CMOS to “Zero,” “None,” or “No hard

drive installed.” Use FDISK.EXE and FORMAT.EXE. Systems using Windows 98 or later can create one single partition (drive letter) on the drive.

• Macintosh

. Use a third-party drive utility (most revisions of Apple’s HD

Setup utility only work with drives having special Apple firmware).

Troubleshooting

• Drive does not spin up. Check cables and all jumper settings. Make sure cable pin 1 (edge stripe) matches PCB pin 1.

• Drive spins , but no LED on/off activity. Check SCS I ID setting. Set th e ID so that each device on the SCSI chain has its own unique ID. See also the next item below. Host I/O controller is usually ID7.

• Computer does not seem to recognize the d rive. Verify that the drive is enabled by the SCSI host adapter setup utility.

• FDISK does not detect the drive. Run the FDISK program located on your Windows startup diskette. Type fdisk/status to verify that your hard drive is present.

Seagate support services

For online information about Seagate products, visit www.seagate.com or e-mail your disc questions to DiscSupport@Seagate.com.

If you need help installing your drive, consult your dealer first. If you need additional help, call a Seagate technical support specialist. Before calling, note your system configuration and drive model number.

Africa +1-405-324-4714 Netherlands 00 800-47324283 Australia 1800-14-7201 New Zealand 0800-443988 Austria 0 800-20 12 90 Norway 00 800-47324283 Belgium 00 800-47324283 Poland 00 800-311 12 38 China* 800-810-9668 Spain 00 800-47324283 Denmark 00 800-47324283 Sweden 00 800-47324283 France 00 800-47324283 Switzerland 00 800-47324283 Germany 00 800-47324283 Singapore 800-1101-150 Hong Kong 800-90-0474 Taiwan* 00-800-0830-1730 Hong Kong† 001-800-0830-1730 Thailand 001-800-11-0032165 India 1-600-33-1104 Turkey 00 800-31 92 91 40 Indonesia 001-803-1-003-2165 United Kingdom 00 800-47324283 Ireland 00 800-47324283 USA/Canada/ 1-800 SE AG ATE or Italy 00 800-47324283 Latin America +1-405 -324-4700 Japan 0034 800 400 554 Other European Malaysia 1-800-80-2335 countries +1-405-324-4714 Middle East +1-405-324-4714

*Mandarin †Cantonese

Warranty. Contact your place of purchase or our web site (above). Return Mercha ndise Au thor izatio n (R MA). Before returning the drive, ver ify that it

is defective. Seagate Worldwide customer service centers are the only facilities authorized to service Seagate drives. Contact nearest center for return procedures and trade regulations.

Shipping the drive Caution. Back up the data before shi pping. Seagate assu mes no responsibility for

data lost during shippin g or service. Sh ipping drive in an unapprove d container void s the warranty. Pack the drive w ith original box and packing materials. Use no other materials. This prevents electrical and physical damage in transit.

Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. Cheetah and the Wave logo are reg ister ed tr ade ma rks or trad ema rks of Seagate Technology LLC. Other product names ar e registered trademarks or trademarks of their owners. Seagate reserves the right to change, without notice, product offerings or

specifications.