Seagate ST3250820SCE, ST3300820SCE, ST3320820SCE, ST3400820SCE, ST3500830SCE User Manual
...
Product Manual
DB35.3 Series Serial ATA
ST3750640SCE
ST3750840SCE
ST3500830SCE
ST3400820SCE
ST3320820SCE
ST3300820SCE
ST3250820SCE
100427570
Rev . D
August 2007
Revision histor y
Revision Date Sheets affected or comments
Rev. A 08/04/06 Initial draft.
Rev. B 08/17/06 4-11 and 21.
Rev. C 07/18/07 ft cover, 1, 3, 4, 6, 8, 10 and 23.
Rev. D 08/2307 1, 39 and 40.
Copyright © 2006-2007 Seagate Technology LLC. All rights reserved. Printed in USA
Publication number: 100427570, Rev. D August 2007
Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC
in the United States and/or other countries. DB35.3 Series, SeaTools and SeaTDD are either trademarks
or registered trademarks of Sea gate Technology LLC or one of its affiliated comp anie s in the United States
and/or other countries. All other trademarks or registered trademarks are the property of their respective
owners.
One gigabyte, or GB, equals one billion bytes when referring to hard drive capacity. Accessible capacity
may vary depending on oper ating envi ronme nt and for matting. Seagate reserves the right to chan ge, wi thout notice, product offerings or specifications.
DB35.3 Series Serial ATA Product Manual, Rev. D
i
Contents
1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 Specification summary tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.3 Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4 Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5 Physical characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.6 Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.7 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.8 Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.8.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.8.2 Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.8.3 Voltage tolerance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.8.4 Power-management modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.9 Environmental specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.9.1 Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.9.2 Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.9.3 Humidity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.9.4 Altitude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.9.5 Shock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.9.6 Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.10 Acoustics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.11 Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.12 Reliability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.13 Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.13.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.13.2 Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.13.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.14 Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.14.1 European Union Restriction of Hazardous Substances (RoHS) Directive. . . . . 23
2.14.2 China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . 23
2.15 Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.0 Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.1 Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.2 Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.3 Serial ATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.4 Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.0 Serial ATA (SATA) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.1 Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.2 Serial ATA device plug connector pin definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.3 Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.3.1 Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.3.2 Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.3.3 S.M.A.R.T. commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
5.0 Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
ii
DB35.3 Series Serial ATA Product Manual, Rev. D
DB35.3 Series Serial ATA Product Manual, Rev. D
iii
List of Figures
Figure 1. Typical 5V startup and operation current profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 2. Typical 12V startup and operation current profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 3. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 4. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 5. Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
DB35.3 Series Serial ATA Product Manual, Rev. D
1
1.0 Introduction
This manual describes the functional, mechanical and interface specifications for the following Seagate
DB35.3 Series Serial ATA model dr ives:
ST3750640SCE ST3500830SCE ST3320820SCE ST3250820SCE
ST3750840SCE ST3400820SCE ST3300820SCE
These drives provide the following key features:
• 7,200 RPM spindle speed.
• High instantaneous (burst) data-transfer rates (up to 150 Mbytes per second).
• Tunneling Magnetoresistive (TMR) recording heads.
• State-of-the-art cache and on-the-fly error-correction algorithms.
• Native Command Queueing with command ordering to increase performance in demanding applications.
• Full-track multiple-sector transfer capability without local processor intervention.
• Quiet operation.
• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
• Support for S.M.A.R.T. drive monitoring and reporting.
• Supports latching SATA cables and connectors.
2
DB35.3 Series Serial ATA Product Manual, Rev. D
1.1 About the Serial ATA interface
The Serial ATA interface provides several advantages over the traditional Parallel ATA interface. The primary
advantages include:
• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other configuration options.
• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.
• Scalability to higher performance levels.
In addition, Serial ATA makes the tra nsition fr om P a rall el ATA easy b y pro vi ding leg acy sof t war e sup port . S erial
ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current
system and expect all of your existing applications to work as normal.
The Serial ATA interface connects each disc drive in a point-to-point configuration with the Serial ATA host
adapter. There is no master/slave relationship with Serial ATA devices like there is with Parallel ATA. If two
drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they
were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0
(master) devices.
Note. The host adapter may, optionally, emulate a master/slave environment to host software where two
devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and
Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a
master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA
environment.
The Serial ATA host adapter and drive share the function of emulating Parallel ATA device behavior to provide
backward compatibility with existing host systems and software. The Command and Control Block registers,
PIO and DMA data transfers, resets, and interrupts are all emulated.
The Serial ATA host adapter cont ai ns a set of registe rs that sha dow the conte nt s of the trad iti onal device r egisters, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized
AT Attachment” specification. The specification can be downloaded from www.serialata.org.
DB35.3 Series Serial ATA Product Manual, Rev. D
3
2.0 Drive specifications
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal
power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the
following drive models:
ST3750640SCE ST3500830SCE ST3320820SCE ST3250820SCE
ST3750840SCE ST3400820SCE ST3300820SCE
2.1 Specification summary tables
The specification s li sted in the fol lowing table are for quick r efer ence. For det ail s on sp ecifi cation measurement
or definition, see the appropriate section of this manual.
4
DB35.3 Series Serial ATA Product Manual, Rev. D
Table 1: Drive specificati o ns summary for 750 Gbyt e m odels
Drive specification ST3750640SCE ST3750840SCE
Formatted Gbytes (512 bytes/sector)* 750
Guaranteed sectors 1,465,149,168
Bytes per sector 512
Default sectors per track 63
Default read/write heads 16
Default cylinders 16,383
Recording density, max 926 kbits/in
Track density, max 145 ktracks/in
Areal density, max 128.2 Gbits/in
Spindle speed 7,200 RPM
Internal data transfer rate, max 1,030 Mbits/sec
Sustained data transfer rate, max 78 Mbytes/sec
I/O data-transfer rate, max 300 Mbytes/sec
ATA data-transfer modes supported PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–6
Cach e buffer 16 Mbytes 8 Mbytes
Height, max 26.1 mm (1.028 inches)
Width, max 101.6 mm (4.000 inches) +/- 0.010 inches
Length, max 146.99 mm (5.787 inches)
Weight, typical 720 grams
Average latency 4.16 msec
Power-on to ready, max 16 sec
Standby to ready, max 16 sec
Track-to-track seek time, typical <0.8 msec read; <1.0 msec write
Average seek, read, typical <11.0 msec
Average seek, write, typical <12.0 msec
Startup current (max) 12V (peak) 2.0 amps
Voltage tolerance (including noise) 5V ± 5%
12V ± 10%
Ambient temperature 0° to 60°C (operating)
–40° to 70°C (nonoperating)
Temperature gradient, per hour max 20°C (operating)
30°C (nonoperating)
Relative humidity 5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient, per hour max 30%
Wet bulb temperature, max 37.7°C (operating)
37.7°C (nonoperating)
Altitude, operating –60.96 m to 3,048 m
(–200 ft. to 10,000+ ft.)
Altitude, nonoperating , max –60.96 m to 12,192 m below mean sea level
(–200 ft. to 40,000+ ft. below mean sea level)
Operational Shock, max 63 Gs at 2 msec
Non-Operational Shock, max 300 Gs at 2 msec
Vibration, operating 5–22 Hz: 0.25 Gs, Limited displacement
22–350 Hz: 0.50 Gs
350–500 Hz:: 0.25 Gs
2
DB35.3 Series Serial ATA Product Manual, Rev. D
5
Drive specification ST3750640SCE ST3750840SCE
Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement
Drive acoustics, sound power
Idle** 2.8 bels (typical)
CE seek profile 3.0 bels (typical)
Nonrecoverable read errors 1 per 10
Annualized Failure Rate (AFR) 0.68%
Warranty 5 years on distribution units.
Contact start-stop cycles (25°C, 50% rel. humidity) 50,000
Supports Hotplug operation per Serial ATA Revision 2.5
specification
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**Dur ing per io ds of driv e idle, some offline activity ma y occ ur accor di ng to the S.M.A.R. T . speci ficati on , whi ch may i ncrea se ac oustic an d
power to operational levels.
22–350 Hz: 5.0 Gs
350–500 Hz:: 1.0 Gs
3.0 bels (max)
3.1 bels (max)
14
bits read
To determine the warranty for a specific drive, use a web browser to
access the following web page:
www.seagate.com/support/service/
From this page, click o n the “Verify Your W arranty” link. You will be asked
to provide the drive serial number, model number (or part number) and
country of purchase. The system will display the warranty information for
your drive.
Yes
6
DB35.3 Series Serial ATA Product Manual, Rev. D
T a ble 2: Drive specifications summary for 500 and 400 Gbyte models
Drive specification ST3500830SCE ST3400820SCE
Formatted Gbytes (512 bytes/sector)* 500 400
Guaranteed sectors 976,773,168 781,422,768
Bytes per sector 512
Default sectors per track 63
Default read/write heads 16
Default cylinders 16,383
Recording density, max 813 kbits/in 781 kbits/in
Track density, max 145 ktracks/in
Areal density, max 114.4 Gbits/in
Spindle speed 7,200 RPM
Internal data transfer rate, max 1,030 Mbits/sec
Sustained data transfer rate, max 72 Mbytes/sec
I/O data-transfer rate, max 300 Mbytes/sec
ATA data-transfer modes supported PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–6
Cach e buffer 8 Mbytes
Height, max 26.1 mm (1.028 inches)
Width, max 101.6 mm (4.000 inches) +/- 0.010 inches
Length, max 146.99 mm (5.787 inches)
Weight, typical 635 grams
Average latency 4.16 msec
Power-on to ready, max 16 sec
Standby to ready, max 16 sec
Track-to-track seek time, typical <0.8 msec read, <1.0 msec write
Average seek, read, typical <11.0 msec
Average seek, write, typical <12.0 msec
Startup current (max) 12V (peak) 2.0 amps
Voltage tolerance (including noise) 5V ± 5%
12V ± 10%
Ambient temperature 0° to 62°C (operating)
–40° to 70°C (nonoperating)
Temperature gradient, per hour max 20°C (operating)
30°C (nonoperating)
Relative humidity 5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient, per hour max 30%
Wet bulb temperature, max 37.7°C (operating)
37.7°C (nonoperating)
Altitude, operating –60.96 m to 3,048 m
(–200 ft. to 10,000+ ft.)
Altitude, nonoperating, max –60.96 m to 12,192 m below mean sea level
(–200 ft. to 40,000+ ft. below mean sea level)
Operational Shock, max 63 Gs at 2 msec
Non-Operational Shock, max 300 Gs at 2 msec
Vibration, operating 5–22 Hz: 0.25 Gs, Limited displacement
22–350 Hz: 0.50 Gs
350–500 Hz:: 0.25 Gs
2
128.2 Gbits/in
2
DB35.3 Series Serial ATA Product Manual, Rev. D
7
Drive specification ST3500830SCE ST3400820SCE
Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement
Drive acoustics, sound power
Idle** 2.8 bels (typical)
CE seek profile 3.0 bels (typical)
Nonrecoverable read errors 1 per 10
Annualized Failure Rate (AFR) 0.68%
Warranty 5 years on distribution units.
Contact start-stop cycles (25°C, 50% rel. humidity) 50,000
Supports Hotplug operation per Serial ATA Revision
2.5 specification
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**Dur ing per io ds of driv e idle, some offline activity ma y occ ur accor di ng to the S.M.A.R. T . speci ficati on , whi ch may i ncrea se ac oustic an d
power to operational levels.
22–350 Hz: 5.0 Gs
350–500 Hz:: 1.0 Gs
3.0 bels (max)
3.1 bels (max)
14
bits read
To determine the warranty for a specific drive, use a web browser to access
the following web page:
www.seagate.com/support/service/
From this page, click on the “Verify Your Warranty” link. You will be asked to
provide the drive serial number, model number (or part number) and country
of purchase. The system will display the warranty information for your drive.
Yes
2.7 bels (typical)
2.9 bels (max)
2.9 bels (typical)
3.0 bels (max)
8
DB35.3 Series Serial ATA Product Manual, Rev. D
T a ble 3: Drive specifications summary for 320 and 300 Gbyte models
Drive specification ST3320820SCE ST3300820SCE
Formatted Gbytes (512 bytes/sector)* 320 300
Guaranteed sectors 625,142,448 586,072,368
Bytes per sector 512
Default sectors per track 63
Default read/write heads 16
Default cylinders 16,383
Recording density, max 781 kbits/in
Track density, max 145 ktracks/in
Areal density, max 114.4 Gbits/in
Spindle speed 7,200 RPM
Internal data transfer rate, max 1,030 Mbits/sec
Sustained data transfer rate, max 72 Mbytes/sec
I/O data-transfer rate, max 300 Mbytes/sec
ATA data-transfer modes supported PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–6
Cach e buffer 8 Mbytes
Height (mm max) 26.1 mm (1.028 inches)
Width (mm max) 101.6 mm (4.000 inches) +/- 0.010 inches
Length (mm max) 146.99 mm (5.787 inches)
Weight (max) 635 grams
Average latency 4.16 msec
Power-on to ready, max 16 sec
Standby to ready, max 16 sec
Track-to-track seek time, typical <0.8 msec read; <1.0 msec write
Average seek, read, typical <11.0 msec
Average seek, write, typical <12.0 msec
Startup current (max) 12V (peak) 2.0 amps
Voltage tolerance (including noise) 5V ± 5%
12V ± 10%
Ambient temperature 0° to 65°C (operating)
–40° to 70°C (nonoperating)
Temperature gradient, per hour max 20°C (operating)
30°C (nonoperating)
Relative humidity 5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient, per hour max 30%
Wet bulb temperature, max 37.7°C (operating)
37.7°C (nonoperating)
Altitude, operating –60.96 m to 3,048 m
(–200 ft. to 10,000+ ft.)
Altitude, nonoperating, max –60.96 m to 12,192 m below mean sea level
(–200 ft. to 40,000+ ft. below mean sea level)
Operational Shock, max 63 Gs at 2 msec
Non-Operational Shock, max 300 Gs at 2 msec
Vibration, operating 5–22 Hz: 0.25 Gs, Limited displacement
22–350 Hz: 0.50 Gs
350–500 Hz:: 0.25 Gs
2
DB35.3 Series Serial ATA Product Manual, Rev. D
9
Drive specification ST3320820SCE ST3300820SCE
Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement
Drive acoustics, sound power
Idle** 2.7 bels (typical)
CE seek profile 2.9 bels (typical)
Nonrecoverable read errors 1 per 10
Annualized Failure Rate (AFR) 0.68%
Warranty 5 years on distribution units.
Contact start-stop cycles (25°C, 50% rel. humidity) 50,000
Supports Hotplug operation per Serial ATA Revision 2.5
specification
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**Dur ing per io ds of driv e idle, some offline activity ma y occ ur accor di ng to the S.M.A.R. T . speci ficati on , whi ch may i ncrea se ac oustic an d
power to operational levels.
22–350 Hz: 5.0 Gs
350–500 Hz:: 1.0 Gs
2.9 bels (max)
3.0 bels (max)
14
bits read
To determine the warranty for a specific drive, use a web browser to
access the following web page:
www.seagate.com/support/service/
From this page, click on th e “Verify Y o ur W ar ranty” link. You will be asked
to provide the drive serial number, model number (or part number) and
country of purchase. The system will display the warranty information for
your drive.
Yes
2.5 bels (typical)
2.7 bels (max)
2.8 bels (typical)
2.9 bels (max)
10
DB35.3 Series Serial ATA Product Manual, Rev. D
T a ble 4: Drive specifications summary for 250 Gbyte models
Drive specification ST3250820SCE
Formatted Gbytes (512 bytes/sector)* 250
Guaranteed sectors 488,397,168
Bytes per sector 512
Default sectors per track 63
Default read/write heads 16
Default cylinders 16,383
Recording density, max 813 kbits/in
Track density, max 145 ktracks/in
Areal density, max 114.4 Gbits/in
Spindle speed 7,200 RPM
Internal data transfer rate, max 1,030 Mbits/sec
Sustained data transfer rate, max 72 Mby tes/ s ec
I/O data-transfer rate, max 300 Mbytes/sec
ATA data-transfer modes supported PIO modes 0–4
Multiword DMA modes 0 –2
Ultra DMA modes 0–6
Cach e buffer 8 Mbytes
Height, max 26.1 mm (1.028 inches)
Width, max 101.6 mm (4.000 inches) +/- 0.010 inches
Length, max 146.99 mm (5.787 inches)
Weight, typical 580 grams (1.28 lb.)
Average latency 4.16 msec
Power-on to ready, max 16 sec
Standby to ready, max 16 sec
Track-to-track seek time, typical <0.8 msec read; <1.0 msec write
Average seek, read, typical <11.0 msec
Average seek, write, typical <12.0 msec
Startup current (max) 12V (peak) 2.0 amps
Voltage tolerance (including noise) 5V ± 5%
12V ± 10%
Ambient temperature 0° to 65°C (operating)
–40° to 70°C (nonoperating)
Temperature gradient, per hour max 20°C (operating)
30°C (nonoperating)
Relative humidity 5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient, per hour max 30%
Wet bulb temperature, max 37.7°C (operating)
37.7°C (nonoperating)
Altitude, operating –60.96 m to 3,048 m
(–200 ft. to 10,000+ ft.)
Altitude, nonoperating, max –60.96 m to 12,192 m below mean sea level
(–200 ft. to 40,000+ ft. below mean sea level)
Operational Shock, max 63 Gs at 2 msec
Non-Operational Shock, max 350 Gs at 2 msec
Vibration, operating 5–22 Hz: 0.25 Gs, Limited displacement
22–350 Hz: 0.50 Gs
350–500 Hz:: 0.25 Gs
2
Loading...