Seagate ST32105WC, ST14207NV, ST14207N, ST32105W, ST32107NV User Manual
...
Seagate T echnology , Inc. P/N 21200027-001, Rev. B
No part of this publication may be reproduced in any form without written permission from
© 1996 Seagate Technology, Inc. All rights reserved.
trademarks of their owners.
trademarks of Seagate Technology, Inc. Other product names are registered trademarks or
Seagate T echnology , Inc. SeaFONE TM , SeaTDD TM , SeaBOARD TM and SeaF AX TM are
Seagate®, Seagate Technology® and the Seagate logo are registered trademarks of
offerings or specifications.
or use of this material. Seagate reserves the right to change, without notice, product
or for incidental consequential damages in connection with the furnishing, performance,
for a particular purpose. Seagate Technology shall not be liable for errors contained herein
material, including, but not limited to, the implied warranties of merchantability and fitness
Documentation: Seagate Technology makes no warranty of any kind with regard to this
consequential or incidental damages, as such, the above limitations may not apply to you.
LOSS OR DAMAGE. Some states do not allow for the exclusion or limitation of liability for
DAMAGES, EVEN IF SEAGATE HAS KNOWLEDGE OF THE POSSIBILITY OF THE POTENTIAL
LOSS OF USE, LOSS OF DATA, OR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
IN NO EVENT WILL SEAGATE’S LIABILITY OF ANY KIND INCLUDE ANY LOST PROFITS,
which vary from state to state.
PURPOSE. This limited warranty gives you specific legal rights. You may have others,
WARRANTY OR CONDITION OF MERCHANT ABILITY OR FITNESS FOR A PARTICULAR
IMPLIED, OR STA TUTOR Y, AND SEAGATE SPECIFICALLY DISCLAIMS ANY IMPLIED
CONDITIONS, SEAGATE MAKES NO W ARRANTIES ON THE PRODUCTS, EXPRESS,
DISCLAIMER: EXCEPT FOR THE ABOVE EXPRESS LIMITED W ARRANTIES OR
misapplication.
This warranty is void if defect has resulted from accident, abuse, unauthorized repair or
prepaid to the authorized Seagate destination.
must be returned in the packaging provided by Seagate with transportation charges
Seagate will replace, at no charge, any drive that does not meet our warranty. The drive
purchase.
year warranty period. The warranty period will be calculated from the date of original
workmanship and will perform to Seagate’s applicable specifications for Seagate’s threeSeagate warrants that your Seagate disc drive will be free from defects in material and
LIMITED WARRANTY STATEMENT
drive warranty and may damage your drive.
Using any other container or packing material voids your
• Save your Seagate packing materials for future use.
user-serviceable components.
• Do not remove the drive cover. The drive contains no
for antistatic grounding.
case. Do not unplug your computer if you will be using it
• Make sure your computer is turned off before opening the
strap.
optimum protection, wear a grounded antistatic wrist
touching the grounded chassis of your computer. For
discharge. Before handling the drive, ground yourself by
• This drive is susceptible to damage from electrostatic
surface.
• Set the drive down only on a flat, padded, non-static
install it.
• Keep the drive in its antistatic bag until you are ready to
printed circuit board.
or frame. Do not touch the connectors or any part of the
• Always handle the disc drive carefully, holding its edges
IMPORTANT PRECAUTIONS
Technical support services
Please read this installation guide before you install your
new drive. If you are not familiar with the procedures
outlined here, have a qualified computer technician perform
the drive installation. If you need assistance installing this
drive, first consult your dealer, who can help you with
system conflicts and other technical issues. If you need
additional assistance, use one of the services listed below,
or call the Seagate support line at 1-800-426-6637.
SeaBOARD: Use a modem to contact the Seagate computer
bulletin board, which supports communications up to 9,600
baud (8-N-1). SeaBOARD is available 24 hours daily.
USA 408-438-8771 France (+33 1) 48 25 35 95
Germany 49-89-140-9331 England 44-1-62-847-8011
Singapore 65-292-6973 Thailand 662-531-8111
Australia 61-2-756-2359 Korea 82-2-556-7294
SeaFAX: Use a touch-tone telephone to access Seagate’s
automated FAX system to receive technical information by
return FAX. This service is available 24 hours daily.
USA 408-438-2620 England 44-1-62-847-7080
SeaTDD: Use a telecommunications device for the deaf
(TDD) to exchange messages with a technical support
specialist. 408/438-5382
Internet Connections: http://www.seagate.com
ftp://ftp.seagate.com
Compuserve Forum: type GO SEAGATE
QQ
UICKUICK
Q
UICK
UICKUICK
QQ
I I
I
I I
NSTNST
ALLAALLA
NST
ALLA
NSTNST
ALLAALLA
ST31080N / WCST31080N / WC
ST31080N / WC
ST31080N / WCST31080N / WC
ST32105N / W / WCST32105N / W / WC
ST32105N / W / WC
ST32105N / W / WCST32105N / W / WC
ST32107N / W/ WC / NVST32107N / W/ WC / NV
ST32107N / W/ WC / NV
ST32107N / W/ WC / NVST32107N / W/ WC / NV
ST14207N / W / WC / NVST14207N / W / WC / NV
ST14207N / W / WC / NV
ST14207N / W / WC / NVST14207N / W / WC / NV
SCSI Hard DrivesSCSI Hard Drives
SCSI Hard Drives
SCSI Hard DrivesSCSI Hard Drives
TIONTION
TION
TIONTION
G G
G
G G
UIDEUIDE
UIDE
UIDEUIDE
J2, Pin 1
50-Pin SCSI
Interface
SCSI Terminators
Remove in all but the last
drive in the chain
J5, Pin 1
4-Pin Power
Connector
1
2
3
4
HDA
Connector
Spin Sync
LED Driver
ID0
ID2
Disable
Spin
E1, Enable
Term Power
Disable
Spin
ID 2
ID1
ID0
J4
J3
J6
J2, Pin 1
50-Pin SCSI
Interface
E1..E3
E5 (Disable Spin)
E6 (Delay Spin)
E7 (Disable Parity)
E4
Reserved
SCSI Terminators
Remove in all but the last
drive in the chain
J4, Pin 1
4-Pin Power
Connector
1
2
3
4
HDA
Connector
Spin Sync
LED Driver
J3
J7
E8, Enable
Term Power In/Out
OE1
OE3
OE5, LED Driver
INSTALLATION
Steps:
1. Turn off the computer and all attached peripheral equipment, such as printers and monitors.
2. Disconnect the AC power cable from the computer.
3. Remove the screws attaching the computer’s cover, and remove the cover from the system.
4. Remove the drive from the ESD (Electro Static Discharge) bag, carefully placing the drive on your work surface.
5. Configure the disk drive jumpers as necessary. Refer to table below for more details.
6. Remove SCSI terminator resitor packs (2) in all drives on the SCSI bus except for the last drive in the chain.
7. Remove and retain any hardware that may be attached to the selected bay.
8. Connect the cables; align the colored striped edge of the interface cable to pin 1 of the drive SCSI interface connector.
9. Partially insert the drive into the drive bay. Select an unused power connector from the power supply and connect it to the drive. If there are no unused
power connections on the power supply, you can purchase a “Y” cable adapter from your dealer . This connector will allow you to add another power
connection for your new drive.
10. Now that the drives are jumpered, connected, and have power cables attached, secure the drive or the mounting frame with four 6-32x.25 screws.
CAUTION: Do not use screws of excess length when attaching the drive. Damage to the drive’s circuit board could result. The maximum insertion in
bottom holes is .25”, the maximum insertion for side holes is .125”.
SCSI Disk Drive Models
Total Tables Jumper W arranty
Blocks LED Table Notes (Y ears)
ST31080N/WC 2,110,812 D a 2 5
ST32105N/W/WC 4,194,304 D b,c 1,2 5
ST31080N/WC
ST32107N/W/WC/NV 4,194,304 D b,c 1,2 5
ST14207N/W/WC/NV 8,388,608 D b,c 1,2 5
Jumper T able
a ID0 ID1 ID2 N/A
b E1E2E3N/A
c OE1 OE2 OE3 N/A
SCSI ID
0 OUT OUT OUT OUT
1 IN OUT OUT OUT
2 OUT IN OUT OUT
3 IN IN OUT OUT
4 OUT OUT IN OUT
5 IN OUT IN OUT
6 OUT IN IN OUT
7 INININOUT
8 OUT OUT OUT IN
9 IN OUT OUT IN
10 OUT IN OUT IN
ST32105/32107/14207/N/W/WC/NV
11 IN IN OUT IN
12 OUT OUT IN IN
13 IN OUT IN IN
14 OUT IN IN IN
15 IN IN IN IN
LED Configuration T able
Letter Connector LED+ LED B J-1 Pin 3 Pin 4
C J-5 Pin 3 Pin 4
D J-3 Pin 3 Pin 4
E J-7 Pin 1 Pin 2
Notes
Note 1 - “W” drives use Jumper T able c, e
Note 2 - “WC” drives have no jumpers
Note 3 - Parity is enabled by default. Install jumper E7 to disable parity .
Note 4 - Most SCSI host adapters are compatible with Seagate drives. Software drivers and installation
* - On some drives J5 may be replaced with an LED.
P/N 21200027-001, Rev. B
instructions are provided with the host adapter. Most drives are shipped with SCSI ID set to 6.
Loading...