Seagate ST3500841A, ST3200827A, ST3500641A, ST3160812A, ST3400833A Product Manual

...

Barracuda 72 00 .9 PATA

ST3500841A ST3200827A ST3500641A ST3160812A ST3400833A ST3160212A ST3400633A ST3120814A ST3300822A ST3120213A ST3300622A ST3802110A ST3250824A ST3402111A ST3250624A

Barracuda 72 00 .9 PATA

ST3500841A ST3200827A ST3500641A ST3160812A ST3400833A ST3160212A ST3400633A ST3120814A ST3300822A ST3120213A ST3300622A ST3802110A ST3250824A ST3402111A ST3250624A

Publication number: 100389997, Rev. C

February 2006

Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC. SeaTools, SeaFONE and SeaTDD are registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners.

Seagate reserves the right to ch ange, witho ut notice, product offerings or spec ifications . No

part of this publication may be reproduc ed in any form w ithout wr itte n per mi ssio n of Seagate

Technology LLC.

Contents

1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1 Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2.2.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2.3 Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2.4 Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2.5 Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.6 Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.7 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.8 Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.8.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.8.2 Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.8.3 Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.8.4 Power-management modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.9 Environmental specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.9.1 Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.9.2 Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.9.3 Humidity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.9.4 Altitude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.9.5 Shock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

2.9.6 Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

2.10 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

2.11 Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

2.12 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

2.13 Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

2.13.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

2.13.2 Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

2.13.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

2.14 Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

2.14.1 European Union Restriction of Hazardous Substances (RoHS) . . . . . . . . . . . . 31

2.15 Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

3.0 Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.1 Handling and static discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.2 Breather filter hole precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

3.3 Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3.3.1 Master/slave configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3.3.2 Cable-select option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3.3.3 Alternate capacity jumper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3.3.4 Ultra ATA/100 cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

3.4 Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

4.0 ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

4.1 ATA interface signals and connector pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

4.1.1 Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

4.1.2 Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

4.1.3 Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

4.1.4 S.M.A.R.T. commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

5.0 Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Barracuda 7200.9 PATA Product Manual, Rev. C iii

iv Barracuda 7200.9 PATA Product Manual, Rev. C

List of Figures

Figure 1. Typical 5V startup and operation current profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Figure 2. Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Figure 3. Breather filter hole location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Figure 4. Master/slave jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Figure 5. Ultra ATA cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 6. Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Figure 7. I/O pins and supported ATA signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Barracuda 7200.9 PATA Product Manual, Rev. C v

vi Barracuda 7200.9 PATA Product Manual, Rev. C

1.0 Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate

Barracuda® 7200.9 PATA model drives:

ST3500841A ST3300622A ST3160212A

ST3500641A ST3250824A ST3120814A

ST3400833A ST3250624A ST3120213A

ST3400633A ST3200827A ST3802110A

ST3300822A ST3160812A ST3402111A

These drives provide the following key features:

• 7,200-RPM spindle speed

• High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5.

• Tunneling Giant magnetoresistive (TGMR) recording heads and EPRML technology, which provide the drives with increased areal density.

• State-of-the-art cache and on-the-fly error-correction algorithms.

• Full-track multiple-sector transfer capability without local processor intervention.

• Quiet operation.

• 350 Gs nonoperating shock.

• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

• Support for S.M.A.R.T. drive monitoring and reporting.

• Support for Read Multiple and Write Multiple commands.

• Support for autodetection of master/slave drives that use cable select (CSEL).

Barracuda 7200.9 PATA Product Manual, Rev. C 1

2 Barracuda 7200.9 PATA Product Manual, Rev. C

2.0 Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases t he drive and this drive are used throughout th is manual to indi cate the following drive models:

ST3500841A ST3300622A ST3160212A ST3500641A ST3250824A ST3120814A ST3400833A ST3250624A ST3120213A ST3400633A ST3200827A ST3802110A ST3300822A ST3160812A ST3402111A

2.1 Specification summary table

The specifications listed in the table below are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual.

Barracuda 7200.9 PATA Product Manual, Rev. C 3

Table 1: Drive specifications summary for 500 Gbyte models

Drive specification ST3500841A ST3500641A

Formatted Gbytes (512 bytes/sector)* 500 Guaranteed sectors 976,773,168 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density, KBPI (kbits/in max) 790.1 Track density , KTPI (ktracks/in avg.) 124.5 Areal density, (Gbits/in Spindle speed (RPM) 7,200 Internal data transfer rate (Mbits/sec max) 815.2 Sustained data transfer rate OD (Mbytes/sec max) 65.0 I/O data-transfer rate (Mbytes/sec max) 100 ATA data-transfer modes supported PIO modes 0–4

Cache buffer 8 Mbytes 16 Mbytes Height (mm max) 26.1 mm (1.028 inches) Width (mm max) 101.6 mm (4.000 inches) +/- 0.010 inches Length (mm max) 146.99 mm (5.787 inches) Weight (max) 710 grams (1.57 lb.) Average latency (msec) 4.16 Power-on to ready (sec max) 13.0 sec Standby to ready (sec max) 13.0 sec Track-to-track seek time (msec typical) <0.8 (read), <1.0 (write) Average seek, read (msec typical) <11.0 Average seek, write (msec typical) <12.0 Startup current (typical) 12V (peak) 2.6 amps Voltage tolerance (including noise) 5V ± 5%

Ambient temperature 0° to 60°C (operating)

Temperature gradient (°C per hour max) 20°C (operating)

Relative humidity 5% to 90% (operating)

Relative humidity gradient 30% per hour max Wet bulb temperature (°C max) 37.7 (operating)

Altitude, operating –60.96 m to 3,048 m

Altitude, nonoperating (below mean sea level, max)

Operational Shock (max at 2 msec) 63 Gs Non-Operational Shock (max at 2 msec) 300 Gs Vibration, operating 5–22 Hz: 0.25 Gs, Limited displacement

avg) 97.96

Multiword DMA modes 0–2 Ultra DMA modes 0–5

12V ± 10%

–40° to 70°C (nonoperating)

30°C (nonoperating)

5% to 95% (nonoperating)

40.0 (nonoperating)

(–200 ft. to 10,000+ ft.) –60.96 m to 12,192 m

(–200 ft. to 40,000+ ft.)

22–350 Hz: 0.5 Gs 350–500 Hz:: 0.25 Gs

4 Barracuda 7200.9 PATA Product Manual, Rev. C

Drive specification ST3500841A ST3500641A

Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement

Drive acoustics, sound power (bels) Idle** 2.8 (typical)

Quiet seek 3.2 (typical)

Nonrecoverable read errors 1 per 10 Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units.

Contact start-stop cycles (25°C, 50% rel. humidity) 50,000

22–350 Hz: 5.0 Gs 350–500 Hz:: 1.0 Gs

3.0 (max)

3.4 (max)

bits read

To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.

Barracuda 7200.9 PATA Product Manual, Rev. C 5

Table 2: Drive specifications summary for 400 Gbyte models

Drive specification ST3400633A ST3400833A

Formatted Gbytes (512 bytes/sector)* 400 Guaranteed sectors 781,422,768 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density, KBPI (kbits/in max) 790.1 Track density , KTPI (ktracks/in avg.) 124.5 Areal density, (Gbits/in Spindle speed (RPM) 7,200 Internal data transfer rate (Mbits/sec max) 815.2 Sustained data transfer rate OD (Mbytes/sec max) 65.0 I/O data-transfer rate (Mbytes/sec max) 100 ATA data-transfer modes supported PIO modes 0–4

Cache buffer 16 Mbytes 8 Mbytes Height (mm max) 26.1 mm (1.028 inches) Width (mm max) 101.6 mm (4.000 inches) +/- 0.010 inches Length (mm max) 146.99 mm (5.787 inches) Weight (max) 710 grams (1.57 lb.) Average latency (msec) 4.16 Power-on to ready (sec max) 13.0 sec Standby to ready (sec max) 13.0 sec Track-to-track seek time (msec typical) <0.8 (read), <1.0 (write) Average seek, read (msec typical) <11.0 Average seek, write (msec typical) <12.0 Startup current (typical) 12V (peak) 2.6 amps Voltage tolerance (including noise) 5V ± 5%

Ambient temperature 0° to 60°C (operating)

Temperature gradient (°C per hour max) 20°C (operating)

Relative humidity 5% to 90% (operating)

Relative humidity gradient 30% per hour max Wet bulb temperature (°C max) 37.7 (operating)

Altitude, operating –60.96 m to 3,048 m

Altitude, nonoperating (below mean sea level, max)

Operational Shock (Gs max at 2 msec) 63 Non-Operational Shock (Gs max at 2 msec) 300 Gs Vibration, operating 5–22 Hz: 0.25 Gs, Limited displacement

avg) 97.69

Multiword DMA modes 0–2 Ultra DMA modes 0–5

12V ± 10%

–40° to 70°C (nonoperating)

30°C (nonoperating)

5% to 95% (nonoperating)

40.0 (nonoperating)

(–200 ft. to 10,000+ ft.) –60.96 m to 12,192 m

(–200 ft. to 40,000+ ft.)

22–350 Hz: 0.5 Gs 350–500 Hz:: 0.25 Gs

6 Barracuda 7200.9 PATA Product Manual, Rev. C

Drive specification ST3400633A ST3400833A

Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement

Drive acoustics, sound power (bels) Idle** 2.8 (typical)

Quiet seek 3.2 (typical)

Nonrecoverable read errors 1 per 10 Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units.

Contact start-stop cycles (25°C, 50% rel. humidity) 50,000

22–350 Hz: 5.0 Gs 350–500 Hz:: 1.0 Gs

3.0 (max)

3.4 (max)

bits read

Barracuda 7200.9 PATA Product Manual, Rev. C 7

Table 3: Drive specifications summary for 300 Gbyte models

Drive specification ST3300622A ST3300822A

Formatted Gbytes (512 bytes/sector)* 300 Guaranteed sectors 586,072,368 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density, KBPI (kbits/in max) 790.1 Track density , KTPI (ktracks/in avg.) 124.5 Areal density, (Gbits/in Spindle speed (RPM) 7,200 Internal data transfer rate (Mbits/sec max) 867.2 Sustained data transfer rate OD (Mbytes/sec max) 76.6 I/O data-transfer rate (Mbytes/sec max) 100 ATA data-transfer modes supported PIO modes 0–4

Cache buffer 16 Mbytes 8 Mbytes Height (mm max) 26.1 mm (1.028 inches) Width (mm max) 101.6 mm (4.000 inches) +/- 0.010 inches Length (mm max) 146.99 mm (5.787 inches) Weight (max) 655 grams (1.44 lb.) Average latency (msec) 4.16 Power-on to ready (sec max) 11.0 sec Standby to ready (sec max) 11.0 sec Track-to-track seek time (msec typical) <0.8 (read), <1.0 (write) Average seek, read (msec typical) <11.0 Average seek, write (msec typical) <12.0 Startup current (typical) 12V (peak) 2.6 amps Voltage tolerance (including noise) 5V ± 5%

Ambient temperature 0° to 60°C (operating)

Temperature gradient (°C per hour max) 20°C (operating)

Relative humidity 5% to 90% (operating)

Relative humidity gradient 30% per hour max Wet bulb temperature (°C max) 37.7 (operating)

Altitude, operating –60.96 m to 3,048 m

Altitude, nonoperating (below mean sea level, max)

Operational Shock (Gs max at 2 msec) 63 Non-Operational Shock (Gs max at 2 msec) 300 Gs Vibration, operating 5–22 Hz: 0.25 Gs, Limited displacement

avg) 97.69

Multiword DMA modes 0–2 Ultra DMA modes 0–5

12V ± 10%

–40° to 70°C (nonoperating)

30°C (nonoperating)

5% to 95% (nonoperating)

40.0 (nonoperating)

(–200 ft. to 10,000+ ft.) –60.96 m to 12,192 m

(–200 ft. to 40,000+ ft.)

22–350 Hz: 0.5 Gs 350–500 Hz:: 0.25 Gs

8 Barracuda 7200.9 PATA Product Manual, Rev. C

Drive specification ST3300622A ST3300822A

Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement

Drive acoustics, sound power (bels) Idle** 2.7 (typical)

Quiet seek 3.0 (typical)

Nonrecoverable read errors 1 per 10 Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units.

Contact start-stop cycles (25°C, 50% rel. humidity) 50,000

22–350 Hz: 5.0 Gs 350–500 Hz:: 1.0 Gs

2.9 (max)

3.2 (max)

bits read

T o determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.

Barracuda 7200.9 PATA Product Manual, Rev. C 9

Table 4: Drive specifications summary for 250 and 200 Gbyte models

Drive specification ST3250624A ST3250824A ST3200827A

Formatted Gbytes (512 bytes/sector)* 250 200 Guaranteed sectors 488,397,168 390,721,968 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density, KBPI (kbits/in max) 790.1 Track density , KTPI (ktracks/in avg.) 124.5 Areal density, (Gbits/in Spindle speed (RPM) 7,200 Internal data transfer rate (Mbits/sec max) 867.2 Sustained data transfer rate OD (Mbytes/sec max) 76.6 I/O data-transfer rate (Mbytes/sec max) 100 ATA data-transfer modes supported PIO modes 0–4

Cache buffer 16 Mbytes 8 Mbytes Height (mm max) 26.1 mm (1.028 inches) Width (mm max) 101.6 mm (4.000 inches) +/- 0.010 inches Length (mm max) 146.99 mm (5.787 inches) Weight (max) 580 grams (1.28 lb.) Average latency (msec) 4.16 Power-on to ready (sec max) 11.0 sec Standby to ready (sec max) 11.0 sec Track-to-track seek time (msec typical) <0.8 (read), <1.0 (write) Average seek, read (msec typical) <11.0 Average seek, write (msec typical) <12.0 Startup current (typical) 12V (peak) 2.6 amps Voltage tolerance (including noise) 5V ± 5%

Ambient temperature 0° to 60°C (operating)

Temperature gradient (°C per hour max) 20°C (operating)

Relative humidity 5% to 90% (operating)

Relative humidity gradient 30% per hour max Wet bulb temperature (°C max) 37.7 (operating)

Altitude, operating –60.96 m to 3,048 m

Altitude, nonoperating (below mean sea level, max)

Operational Shock (Gs max at 2 msec) 63 Non-Operational Shock (Gs max at 2 msec) 350 Gs Vibration, operating 5–22 Hz: 0.25 Gs, Limited displacement

avg) 97.69

Multiword DMA modes 0–2 Ultra DMA modes 0–5

12V ± 10%

–40° to 70°C (nonoperating)

30°C (nonoperating)

5% to 95% (nonoperating)

40.0 (nonoperating)

(–200 ft. to 10,000+ ft.) –60.96 m to 12,192 m

(–200 ft. to 40,000+ ft.)

22–350 Hz: 0.5 Gs 350–500 Hz:: 0.25 Gs

10 Barracuda 7200.9 PATA Product Manual, Rev. C

Drive specification ST3250624A ST3250824A ST3200827A

Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement

Drive acoustics, sound power (bels) Idle** 2.7 (typical)

Quiet seek 3.0 (typical)

Nonrecoverable read errors 1 per 10 Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units.

Contact start-stop cycles (25°C, 50% rel. humidity) 50,000

22–350 Hz: 5.0 Gs 350–500 Hz:: 1.0 Gs

2.9 (max)

3.2 (max)

bits read

Barracuda 7200.9 PATA Product Manual, Rev. C 11

Table 5: Drive specifications summary for 160 Gbyte models

Drive specification ST3160812A ST3160212A

Formatted Gbytes (512 bytes/sector)* 160 Guaranteed sectors 312, 581,8 08 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density, KBPI (kbits/in max) 840.0 Track density , KTPI (ktracks/in avg.) 141.5 Areal density, (Gbits/in Spindle speed (RPM) 7,200 Internal data transfer rate (Mbits/sec max) 867.2 Sustained data transfer rate OD (Mbytes/sec max) 83.0 I/O data-transfer rate (Mbytes/sec max) 100 ATA data-transfer modes supported PIO modes 0–4

Cache buffer 8 Mbytes 2 Mbytes Height (mm max) 26.1 mm (1.028 inches) Width (mm max) 101.6 mm (4.000 inches) +/- 0.010 inches Length (mm max) 146.99 mm (5.787 inches) Weight (max) 580 grams (1.28 lb.) Average latency (msec) 4.16 Power-on to ready (sec max) <10.0 sec Standby to ready (sec max) <10.0 sec Track-to-track seek time (msec typical) <0.8 (read), <1.0 (write) Average seek, read (msec typical) <11.0 Average seek, write (msec typical) <12.0 Startup current (typical) 12V (peak) 2.6 amps Voltage tolerance (including noise) 5V ± 5%

Ambient temperature 0° to 60°C (operating)

Temperature gradient (°C per hour max) 20°C (operating)

Relative humidity 5% to 90% (operating)

Relative humidity gradient 30% per hour max Wet bulb temperature (°C max) 37.7 (operating)

Altitude, operating –60.96 m to 3,048 m

Altitude, nonoperating (below mean sea level, max)

Operational Shock (Gs max at 2 msec) 63 Non-Operational Shock (Gs max at 2 msec) 350 Gs Vibration, operating 5–22 Hz: 0.25 Gs, Limited displacement

avg) 119.0

Multiword DMA modes 0–2 Ultra DMA modes 0–5

12V ± 10%

–40° to 70°C (nonoperating)

30°C (nonoperating)

5% to 95% (nonoperating)

40.0 (nonoperating)

(–200 ft. to 10,000+ ft.) –60.96 m to 12,192 m

(–200 ft. to 40,000+ ft.)

22–350 Hz: 0.5 Gs 350–500 Hz:: 0.25 Gs

12 Barracuda 7200.9 PATA Product Manual, Rev. C

Drive specification ST3160812A ST3160212A

Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement

Drive acoustics, sound power (bels) Idle** 2.5 (typical)

Quiet seek 2.8 (typical)

Nonrecoverable read errors 1 per 10 Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units.

Contact start-stop cycles (25°C, 50% rel. humidity) 50,000

22–350 Hz: 5.0 Gs 350–500 Hz:: 1.0 Gs

2.7 (max)

3.0 (max)

bits read

Barracuda 7200.9 PATA Product Manual, Rev. C 13

+ 47 hidden pages

Seagate ST3500841A, ST3200827A, ST3500641A, ST3160812A, ST3400833A Product Manual

Specifications and Main Features

Frequently Asked Questions

User Manual