Seagate MOMENTUS ST960813AS, MOMENTUS ST9120822AS, MOMENTUS ST9160821AS, MOMENTUS ST9100828AS, MOMENTUS ST980811AS user manual

...

Product Manual

Momentus® 5400.3 SATA

ST9160821AS ST9120822AS ST9100828AS ST980811AS ST960813AS ST940814AS

100398882 Rev . D August 2007

Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate

Technology LLC in the United States and/or other countries. Momentus, SeagateSeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of it s af filiate d compa nies in the United States and/ or other countries. All other trademarks or registered trademarks are the property of their respective owners.

One gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. Quantitative usage examples for various applications are for illustrative p urpo ses. Actual quan tities w ill vary based on vari ou s factors, including fi le size, file format, features and application software. Seagate reserves the right to change, without notice, product offerings or specifications.

Momentus 5400.3 SATA Product Manual, Rev. D

Contents

1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1 Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.3 Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.4 Physical organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.5 Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.6 Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.7 Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.8 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.9 Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.9.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.9.2 Deferred spinup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.9.3 Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.9.4 Voltage tolerance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.9.5 Power-management modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.10 Environmental specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.10.1 Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.10.2 Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.10.3 Humidity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.10.4 Altitude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.10.5 Shock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.10.6 Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.11 Acoustics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.12 Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.13 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.14 Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.14.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.14.2 Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.14.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.15 Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.15.1 European Union Restriction of Hazardous Substances (RoHS) . . . . . . . . . . . . 16

2.16 Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.0 Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.1 Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.2 Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.3 Serial ATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.4 Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.0 Serial ATA (SATA) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.1 Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.2 Serial ATA device plug connector pin definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.3 Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4.3.1 Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4.3.2 Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4.3.3 S.M.A.R.T. commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5.0 Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Momentus 5400.3 SATA Product Manual, Rev. D

iii

List of Figures

Figure 1. Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 2. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 3. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 4. Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Momentus 5400.3 SATA Product Manual, Rev. D

1.0 Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate Momentus® 5400.3 SATA model drives:

• ST9160821AS

• ST9120822AS

• ST9100828AS

• ST980811AS

• ST960813AS

• ST940814AS These drives provide the following key features:

• 5,400-RPM spindle speed.

• 8-Mbyte buffer.

• Quiet operation. Fluid Dynamic Bearing (FDB) motor.

• High instantaneous (burst) data-transfer rates (up to 150 Mbytes per second).

• Tunneling Magnetoresistive (TMR) recording heads.

• State-of-the-art cache and on-the-fly error-correction algorithms.

• Full-track multiple-sector transfer capability without local processor intervention.

• 900 Gs nonoperating shock and 350 Gs of operating shock.

• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

• The 3D Defense System™, w hich in clu des Drive Defense , D at a Defen se and D iagnost ic Defense, offers the

industry’s most comprehensive protection for disc drives.

• Support for S.M.A.R.T. drive monitoring and reporting.

• Support for Read Multiple and Write Multiple commands.

Momentus 5400.3 SATA Product Manual, Rev. D

1.1 About the Serial A TA interface

The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include:

• Easy installation and configuration with true plug-and-play connectivity. It is not normally necessary to set any jumpers or other configuration options.

• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.

• Scalability to higher performance levels.

In addition, Serial ATA makes the transition from parallel ATA easy by providing le gacy sof twar e suppo rt. S erial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current system and expect all of your existing applications to work as normal.

The Serial ATA interface connects each disc drive in a point-to-point configuration with the S erial ATA host adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they were both “masters” on two separate ports. This essentially means both drives behave as if they ar e Device 0 (master) devices.

Note. The host adapter may, optionally, emulate a master/slave environment to host software where two

devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA environment.

The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing host systems and software. The Command and Control Block registers, PIO and DMA data transfers, resets, and interrupts are all emulated.

The Serial ATA host adapter cont ains a set of regi ste rs that sha dow the conte nt s of the trad i tional devi ce r egisters, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. The specification can be downloaded from http://www.serialata.org.

Momentus 5400.3 SATA Product Manual, Rev. D

2.0 Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the ST9160821AS, ST9120822AS, ST9100828AS, ST980811AS, ST960813AS, and ST940814AS models.

2.1 Specification summary table

The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual.

T a ble 1: Drive speci ficat ion s

Drive specification ST9160821AS ST9120822AS ST9100828AS ST980811AS ST960813AS ST940814AS

Formatted Gbytes (512 bytes/sector)*

Guaranteed sectors 312,581,808 234,441,648 195,371,568 156,301,488 117,210,240 78,340,160 Bytes per sector 512 Physical read/write heads 433221 Discs 222111 Cache (Mbytes) 8 Recording density in BPI

(bits/inch max) Track density TPI (tracks/inch max) 150k Areal density (Gbits/inch2 max) 132 Spindle speed (RPM) 5,400 Internal transfer rate

(Mbits/sec max) I/O data transfer rate

(Mbytes/sec max) ATA data-transfer modes supported SATA 1.0, Serial ATA Revision 2.5

Height (max) 9.5 +/- 0.2 mm (0.374 +/- .0078 inches) Width (max) 69.85 mm (2.75 +/- 0.0098 inches) Length (max) 100.50 +/- 0.25 mm (3.957 +/- 0.010 inches) Weight (typical) 100 grams (0.22 lb) 96 grams (0.21 lb) Average latency (msec) 5.6 Power-on to ready (sec typical) 3.0 Standby to ready (sec typical) 3.0 Track-to-track seek time

(msec typical)

160 120 100 80 60 40

870k

352

150

PIO modes 0–4 Multiword DMA modes 0–2 Ultra DMA modes 0–6

1.0 (read), 1.5 (write)

Momentus 5400.3 SATA Product Manual, Rev. D

T a ble 1: Drive speci ficat ion s

Drive specification ST9160821AS ST9120822AS ST9100828AS ST980811AS ST960813AS ST940814AS

Average seek, read (msec typical) 11.0 Average seek, write (msec typical) 13.0 Full-stroke seek (msec) 22 (typical); 24 (max) Startup current, +5V (typical) 1.0 amps Seek power (typical) 2.0 watts Read/write power (typical) Read: 1.9 watts; Write: 1.8 watts Idle mode, low power (typical) 0.6 watts Standby mode 0.2 watts (typical)*** Sleep mode 0.2 watts (typical)*** Voltage tolerance (including noise) +5V ± 5% Ambient temperature 0° to 60°C (operating), –40° to 70°C (nonoperating) Temperature gradient

(°C per hour max) Relative humidity 5% to 90% (operating)

Relative humidity gradient 30% per hour max Wet bulb temperature

(°C max) Altitude, operating –304.8 m to 3,048 m (–1000 ft to 10,000+ ft) Altitude, nonoperating

(meters below mean sea level, max)

Shock, operating (Gs max at 2 msec)

Shock, nonoperating (Gs max at 2 msec)

Shock, nonoperating (Gs max at 1 msec)

Shock, nonoperating (Gs max at 0.5 msec)

Vibration, operating 1.0 G (0 to peak, 5–500 Hz) Vibration, nonoperating 5 Gs (0 to peak, 5–500 Hz) Drive acoustics, sound power

(bels) Idle** 2.4 (typical)

Performance seek 3.0 (typical)

Nonrecoverable read errors 1 per 10 Annualized Failure Rate (AFR) <0.60% Load/Unload (U/UL) cycles

25°C, 50% relative humidity

32°C, 80% relative humidity 5°C, 80% relative humidity 5°C, 10% relative humidity 55°C, 16% relative humidity

20°C (operating) 30°C (nonoperating)

5% to 95% (nonoperating)

30 (operating) 40 (nonoperating)

–304.8 m to 12,192 m (–1000 ft to 40,000+ ft)

350

800

900

400

2.6 (max)

3.2 (max)

bits read

600,000 software-controlled power on/off cycles 20,000 hard power on/off cycles

Momentus 5400.3 SATA Product Manual, Rev. D

T a ble 1: Drive speci ficat ion s

Drive specification ST9160821AS ST9120822AS ST9100828AS ST980811AS ST960813AS ST940814AS

Warranty 5 years on distribution units.

Supports Hotplug operation per Serial AT A Revision 2.5 specification

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During period s of driv e idle, some offline activity may occu r ac cor ding to th e S. M.A .R.T. s pe cif icati on, whi ch ma y in crease acoustic and

power to operational levels.

***Typical notebooks will pull power to th e drive when ente ring S3 and S4; while in the S3 and S4 states, dr ive sleep and drive standby

modes will not contribute to battery power consumption.

To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.

Yes (requires COMPRESET from host after a hotplug event)

2.2 Formatted ca pacity

Model Formatted capacity* Guaranteed sectors Bytes per sector

ST9160821AS 160 Gbytes 312,581,808 512 ST9120822AS 120 Gbytes 234,441,648 512 ST9100828AS 100 Gbytes 195,371,568 512 ST980811AS 80 Gbytes 156,301,488 512 ST960813AS 60 Gbytes 117,210,240 512 ST940814AS 40 Gbytes 78,140,160 512

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating en viron ment

and formatting.

2.2.1 LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above.

See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48bit addressing support of drives with capacities over 137 Gbytes.

2.3 Default logi cal geometr y

Cylinders Read/write heads Sectors per track

16,383 16 63

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above.

Momentus 5400.3 SATA Product Manual, Rev. D

2.4 Physical organization

Drive model Read/write heads Number of discs

ST9160821AS 4 2 ST9120822AS 3 2 ST9100828AS 3 2 ST980811AS 2 1 ST960813AS 2 1 ST940814AS 1 1

2.5 Recording and interfac e te ch no l o gy

Interface Serial ATA (SATA) Recording method Perpendicular Recording density BPI (bits/inch max) 870k Track density TPI (tracks/inch max) 150k Areal density (Gbits/inch2 max) 132 Spindle speed (RPM) (± 0.2%) 5,400 Maximum Internal transfer rate (Mbits/sec) 352 I/O data-transfer rate (Mbytes/sec max) 150 Interleave 1:1 Cache buffer 8 Mbytes (8,192 kbytes)

2.6 Physical characteristics

Drive specification

Height (mm)

(inches)

Width (mm)

(inches)

Length (mm)

(inches)

Typical weight

ST9160821AS ST9120822AS ST9100828AS

ST980811AS ST960813AS ST940814AS

9.5 +/-0.2

0.374 +/-0.0078

69.85 +/-0.25

2.75 +/-0.0098

100.50 +/-0.25

3.957 +/-0.010

100 grams

0.22 pounds

96 grams

0.21 pounds

Momentus 5400.3 SATA Product Manual, Rev. D

2.7 Seek time

Seek measurem ent s a re t ake n wi th nom inal po w er a t 25 °C amb ient temperature. All times are measured usi ng drive diagnostics. The specifications in the table below are defined as follows:

• Track-to-track seek time is an average of all possible single-track seeks in both directions.

• Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead.

Table 2: Typical seek times

T yp ical seek times (msec) Read Write

Track-to-track 1.0 1.5 Average 11.0 13.0 Full-stroke 22.0 24.0 Average latency 5.56 5.56

Note. These drives ar e de si gned to consisten tl y me et t he se ek t imes r epr esente d in thi s manu al. P hysical

seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted values. However, due to the manner in which these drives are formatted, benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications.

2.8 Start/stop times

Time to ready Typical

Power-on to Ready (sec) 3.0 8.0 St andby to Ready (sec) 3.0 8.0

Max @ 25°C

Momentus 5400.3 SATA Product Manual, Rev. D

2.9 Power specifications

The drive receives DC power (+5V) through a native SATA power connector.

2.9.1 Power consumption

Power requiremen ts for the dr iv es are listed i n the ta ble on p age 8. Typical power measurements are ba sed on an average of drives tested, under nominal conditions, at 25°C ambient temperature.

• Spinup power

Spinup power is measured from the time of power-on to the time that the drive spindle re aches operating speed.

• Seek mode

During seek mod e, the read /write actuator arm move s toward a spe cific positi on on the d isc surface and does not execute a read or write operati on. Servo ele ctronics ar e acti ve. Seek mode power is mea sure d based on three random seek operations every 100 msecs. This mode is not typical.

• Read/write power and current Read/write power is measured with the heads on track, based on three 63 sector read or write operations

every 100 msecs.

• Idle mode power

Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random track location.

• Standby mode

During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/ write electronics are in power-down model

T a ble 3: DC power

Power di s s ipation +5V input average (25° C )

Spinup (typical) 1.0 amps Seek 2.0 watts Read 1.9 watts Write 1.8 watts Idle, performance* 1.4 watts Idle, active* 0.75 watts Idle, low power mode* 0.6 watts Standby 0.2 watts Sleep 0.2 watts

*During periods of drive i dle, some offl ine activity may occur acc ording to the S. M.A.R.T. speci fica tion, which may i ncrease acoust ic and

power to operational levels.

+ 30 hidden pages