Seagate KSD-541-P, KSD-541 User Manual

Industrial 5-Port Fa st Ethernet Switches

with SFP Slot a nd optional 4 PoE PSE Ports

Basic Model: KSD-541

PoE Model: KSD-541-P

Installation Guide

DOC.080104

-1-

(C) 2008 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in
any form or by any means or used to make any directive work (such as translation or transformation)
without permission from KTI Networks Inc.

KTI Networks Inc. reserves the right to revise this documentation and to make changes in content
from time to time without obligation on the part of KTI Networks Inc. to provide notification of such
revision or change.

For more information, contact:

United States KTI Networks Inc.

P.O. BOX 631008
Houston, T exas 77263-1008

Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
URL: http://www.ktinet.com/

International Fax: [phone]

E-mail: [e-mail]
URL: http://www.ktinet.com.tw/

-2-

The information contained in this document is subject to change without prior notice. Copyright (C). All
Rights Reserved.

TRADEMARKS

Ethernet is a registered trademark of Xerox Corp.

WAR NING:

This equipment ha s been tested a nd found to comply with the limits f or a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and if not installed and used in accordance with the
instruction manual may cause harmful interference in which case the user will be required to correct the
interference at his own expense.

NOTICE:

(1 ) The changes or modifications not expressively approved by the party responsible for compliance
could void the user's authority to operate the equipment.
(2) Shielded interface cables and AC power cord, if any, must be used in order to comply with the
emission limits.

CISPR A COMPLIANCE:

This device complies with EMC directive of the European Community and meets or exceeds the following
technical standard.
EN 55022 - Limits and Methods of Measurement of Radio Interference Characteristics of Information
T echnology Equi pment. This device complies with CISPR Cla ss A.

CE NOTICE
Marking by the symbol

indicates compliance of this equipment to the EMC directive of the Euro-

pean Community . Such marking is indicative that this equi pment meets or exceeds the following techni­cal standards:

EN 55022: Limits and Methods of Measurement of Radio Interference characteristics of Information
T echnology Equi pment.

EN 50082/1:Generic Immunity Sta ndard -Part 1: Domestic Commercial a nd Light Industry .
EN 60555-2: Disturbances in supply systems caused by household appliances and similar electrical

equipment - Part 2: Harmonics.

-3-

Ta ble of Contents

1. Introduction.................................................................................................. 5

1.1 Features ...................................................................................................................6

1.2 Product Panels.........................................................................................................6

1.3 LED Indicators..........................................................................................................6

1.4 Specifications...........................................................................................................7

2. Installation .................................................................................................... 9

2.1 Un packing.................................................................................................................9

2.2 Safety Cautions ........................................................................................................9

2.3 Mounting the Switch on a Wall...................................................................................9

2.4 Din-Rail Mounting ....................................................................................................10

2.5 Panel Mounting ........................................................................................................ 11

2.6 Applying Power ........................................................................................................ 11

3. Making Connections.................................................................................. 13

3.1 Making UTP Connections .......................................................................................1 3

3.2 Making Fiber Conne ction ........................................................................................13

3.3 Ma king PoE Connections .......................................................................................14

3.4 LED Indication ........................................................................................................15

4. Application s ............................................................................................... 16

4.1 Application s with Basic Switch Model .....................................................................1 6

4.2 Application s with PoE Switch Model.......................................................................17

-4-

1. Introduction

The switches are 5-port Fast Ethernet switches which are featured with four copper ports and one
combo port. The combo port comes with one RJ-45 and one SFP slot. The SFP slot can be mounted
with a fiber tra nsce iver optionally to support a fiber connection.

For more coming PoE (Power Over Ethernet) applications, the PoE switch model is equipped with PoE
design in four copper ports. With proper 48VDC power supply, it is able to deliver power to four PoE PD
devices via Cat.5 ca bles. This guide describe s the installation information about two models a s follows:

Basic Model Industrial 5-port Fa st Ethernet switch with SFP slot
PoE Model Industrial 5-port Fast Ethernet switch with SFP slot and PoE feature

In summary , the switch provides the following a dvantages:

Plug a nd Play

No configuration is required in using the switch. W ith the featured auto-negotiation function, the switch
ca n detect a nd configure the connection speed a nd duplex automatically . The switch also provides auto
MDI/MDI-X function, which ca n detect the connected ca ble and switch the tra nsmission wire pair and
receiving pair automatically . This auto-crossover function ca n si mplify the type of network cables used.

Fiber Connectivity

For fiber connection, the SFP slot can be installed with an optional SFP optical fiber transceiver to
support one fiber connection when needed.

Power over Ethernet

For PoE applications, four IEEE 802.3af-complia nt PoE PSE ports are provided in four copper ports.
Each PSE port can deliver +48VDC power to one PoE PD (Powered Device) via the connected Cat.5
cable.

Industrial Features

For industrial environment, the devices are designed with the following enhanced features exceeding
that of commercial Ethernet switches:

• High and wide operating T emperature

• Power input interface: Industrial screw terminal block and DC power jack for external
commercial power adapter a s option

• Screw pa nel and DIN rail mounting support for industri al enclosure

• Industrial-rated Emission a nd Immunity performance

-5-

1.1 Features

 Provides 5 10/100Mbps RJ-45 a nd one 100Mbps SFP slot
 All copper ports support auto-negotiation and auto-MDI/MDI-X detection
 Provides full wire speed forwarding
 Supports IEEE 802.3x flow control for full-duplex a nd ba ckpressure f or half-duplex
 Provides SFP slot for optional optical fiber connection
 Provides four IEEE 802.3af-compli ant PoE PSE ports
 Provides two types of power supply interfaces - DC Jack and terminal block
 Supports sta nd-alone, wall, Din-Rail, a nd pa nel mounting
 Industrial-rated emission and i mmunity performa nce

1.2 Product Panels

The following figure illustrates the fa ces of the switch:

1.3 LED Indicators

LED Function

POWER Power status
LINK/ACT Port link status and activities (Port 1 - Port 5)
100M/10M Port speed status (Port 1 - Port 5)
PoE STATUS Port PoE power status (Port 2 - Port 5)
SFP/RJ-45 Port 1 SFP / RJ-45 selection status

-6-